1. 3fe574b.exe Driver
2. PATHWORK.TXT File Contents

PATHWORK.TXT Driver File Contents (3fe574b.exe)

3Com Corporation
3CCFE574BT 10/100 LAN PC Card
3CXFE574BT 10/100 LAN PC Card
NDIS 2.01 Drivers Installation Notes

DEC Pathworks for DOS/Windows v4.1 (below)
DEC Pathworks for DOS/Windows  v5.1  


DEC PATHWORKS for DOS/Windows v5.1
=====================================

These instructions describe how to install 
the 3Com NDIS driver for the DEC Pathworks 
network operating system.

These instructions assume the DEC Pathworks 
software has been installed on the hard 
drive from the installation diskettes 
or CD ROM. Refer to the DEC manual for 
installation instructions if the software 
has not been installed.  Refer to the DEC 
manual for templates and options.  

Note:  
Please read the WFW.TXT file on the Installation Disk  
if you are installing Pathworks with WFW  v3.11. 

Please run AutoLink on the Installation disk if you are 
installing Pathworks with Retail NetWare or Netware 
with ODI drivers. 

 1. Go to the drive where Pathworks software is             
    installed. 

 2. Change directory to PCAPP.

 3. Execute PWSETUP.

 4. Enter the directory where you want the software
    installed. The default is C:\PW. 

 5. Choose CUSTOMIZE under the Select A Configuration
    Option menu.

 6. Choose a template in the Select a 
    Workstation Template menu.

 7. Under the Customize: Modify Workstation            
    Configuration menu, put an X mark beside the
    Network Adapter Information line.

 8. Additional menus will appear, 
    choose the appropriate options for your 
    network environment. 
    Refer to the DEC manual if there are questions         
    regarding these menus.

 9. Choose <Other Network Adapter> under 
    the Customize: Network Adapter Information menu.

10. If installing options other than 
    Retail NetWare or Netware with ODI drivers: 

    On the Driver File line, type the following:

a:\mslanman.dos\drivers\ethernet\el3c574\el3c574.dos

On the PROTOCOL.INI Stub: line, type the following:
        a:\mslanman.dos\drivers\ethernet\el3c574\protocol.ini 
on

11. Verify that (l) Ethernet is marked and click on OK.

12. Click on OK under the  Customize: Network Adapter 
    Information menu.

13. Additional menus will appear, follow the DEC
    instructions to complete the installation.

14. Reboot the PC.


DEC PATHWORKS for DOS/Windows v4.1
=====================================


To install DEC PATHWORKS version 4.1 on a DOS NDIS
workstation, DOS must be installed on the target
workstation C: drive, or you must have a bootable DOS
floppy.  Follow these steps:

 1. Insert the PATHWORKS DOS Client Setup     
    diskette version 4.1 in your floppy drive.

 2. Change to that drive and execute the 
    NETSETUP.EXE program.

 3. Follow the screens to select a 
    Transport Protocol.

 4. Insert the appropriate diskettes for 
    the selection you made in step 3.

 5. Select your network adapter by typing 
    ETHERNET.
 
 6. Select the option (OTHER NDIS) adapters.

 7. When prompted for the DRIVE:\PATH\FILENAME for the      
    NDIS driver, type:

A:\MSLANMAN.DOS\DRIVERS\ETHERNET\EL3c574\EL3C574.DOS

 8. When prompted for the full DRIVE:\PATH of     
    the PROTOCOL.INI fragment, type:

    A:\ MSLANMAN.DOS\DRIVERS\ETHERNET\EL3C574\PROTOCOL.INI

 9. Follow the rest of the installation 
    screens and the procedure for writing 
    the KEY DISK.

The NETSETUP program will build 
the PROTOCOL.INI file for you and 
modify your startup files to use 
the adapter you have selected.

NOTE: 
You must add the /N parameter to the line in the STARTNET.BAT file. 
That starts the network scheduler.

For example:

%BOOT%\DECNET\sch /h /n

%VER 1.000.002