1. Trend-Net_TE-16Xpress.zip Driver
2. README.TXT File Contents

README.TXT Driver File Contents (Trend-Net_TE-16Xpress.zip)

TRENDnet Support Publishing       \UNIXWARE\README.TXT

           TRENDnet TE-16XP Ethernet Adapter Installation
                   for UnixWare 2.0

 Contents
 ÄÄÄÄÄÄÄÄ
     Introduction
     Requirements
     Minimum Skill Level
     Compatibility List
     Getting Started

 Introduction
 ÄÄÄÄÄÄÄÄÄÄÄÄ
    This installation assumes that the adapter is working properly.
    Please consult \SETUP\README.TXT for help with setup of the adapter.
    Getting Started will describe the installation instructions.

 Requirements
 ÄÄÄÄÄÄÄÄÄÄÄÄ
     An ISA compatible computer
     Novell/SCO UnixWare 2.x
     A TE-16XP Ethernet Adapter
     A knowledge of basic Unixware commands and editing text files

 Minimum Skill Level
 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
     A knowledge of basic UnixWare commands
     A knowledge of editing text files
     A knowledge of UnixWare basic file structure
     A knowledge of the network driver configuration being used
     Please see Support Options if you are not comfortable will this
      skill level

 Compatibility List
 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
     Any TE-16XP Ethernet Adapter
     For a Motherboard compatibility list please consult your local
      Branch Office

 Getting Started
 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
     Login to UNIX as root
     Execute the following commands:

        #doscp a:/unixware/setup setup
        #chmod +x setup
        #./setup  a:/unixware (modify path as needed)

     Install the driver by typing the following:

        #cd /usr/lib/tcprt/eth
        #chmod +x setupisa
        #./setupisa

      The program displays the following message:

        Do you wish to install or delete the network driver(i/d/q)?

     Type "i" to install.

    First Adapter
    ÄÄÄÄÄÄÄÄÄÄÄÄÄ
        Do you want to configure Board_0? (y/n/q)

     Type "y" for yes.  The following messages appear:

        Board_0 configuring ...

        Please enter the IP host name for the device d22e_0(default:xx )
        Please Initialize the IP Address for host XXXX:
        Configure host XXXX with default Ethernet(TM) ifconfig option?

     Answer the first two prompts accordingly
     For the last prompt, answer "yes"

      NOTE:
        For non-PnP adapter, specify the I/O base address and IRQ number of
        the adapter via the Setup program. Make sure the specified values
        do not conflict with other adapters on the system.

      The following prompt then appears:

         Please choose the media mode that you want............

                0. Twisted pair connection.
                1. BNC connection.
                2. AUI connection.
                3. Automatic detection between TP BNC and AUI.
                4. Use EEPROM setting.

     Enter number of media mode selection  [3] :

    Second Adapter
    ÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
        Do you want to configure Board_1? (y/n/q)

     Type "y" for yes. The following messages appear:

        Board_1 configuring ...

        Please enter the IP host name for the device d22e_1(default:xx )
        Please Initialize the IP Address for host YYYY:
        Configure host YYYY with default Ethernet(TM) ifconfig option?

     Answer the first two prompts accordingly.
     For the last prompt, answer "yes"..

      NOTE:
        For non-PnP adapter, specify the I/O base address and IRQ number of
        the adapter via the Setup program.  Make sure the specified values
        do not conflict with other adapters on the system.

      The following prompt then appears:

        Please choose the media mode that you want............

                0. Twisted pair connection.
                1. BNC connection.
                2. AUI connection.
                3. Automatic detection between TP BNC and AUI.
                4. Use EEPROM setting.

     Enter number of media mode selection  [3] :
     Repeat these steps for additional adapters.

    Netware Support
    ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
        The following prompt appears:

                0: d22e_0 adapter 0
                1: d22e_1 adapter 1
                2: d22e_2 adapter 2
                3: d22e_3 adapter 3
                Select one adapter to support NetWare:

     Select "0".

     After installing the device driver, create a desktop user with "root"
      privileges.
     Run/Select Administrator Tools, and follow this procedure
        Admin_Tools -> Networking
                    -> NetWare_Setup
                    -> LAN options
                    -> IPX LAN Device
                    -> IPX LAN Frame Type

     IPX LAN Device specifies the device driver for the adapter
     IPX LAN Frame Type specifies the ethernet frame type



How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

• Expand the archive file (if the download file is in zip or rar format).

• If the expanded file has an .exe extension, double click it and follow the installation instructions.

• Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

• Find the device and model you want to update in the device list.

• Double-click on it to open the Properties dialog box.

• From the Properties dialog box, select the Driver tab.

• Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.