Additional Information
MM MS5000-E Data+Fax+Voice Modem Card Ver 1.0
Installation on Win 95 Platform
================================
1. Win95 will automatically detect the MS5000 PnP Modem Card
and displays the "New Hardware Found" dialog box.
2. Insert the installation diskette provided into either drive
A or B.
3. Select the "Driver from disk provided by Hardware manufacturer
option and click OK.
4. Type A:\ (or B:\) in the combo box and click OK.
You might encounter some resource conflicts after loading the PnP modem
device (especially when there are non-Plug & Play adaptors installed in
your system). To alter the resource configurations, go to Control Panel
- System - Device Manager and click on "Modem". Choose the modem device
and click on "Properties". You can change the settings for both comport
and interrupt. For choosing interrupts, you can select IRQ 3,4,5,10,11,
15 depending which are available.
For further details, please refer to Trouble-shooting section in Windows 95.
Installation on Win 95/OSR2 Platform
=====================================
1. Win95 will automatically detect the MS5000 PnP Modem Card after
which the system will prompt the "Update Device Driver Wizard"
dialog box.
2. Insert the installation diskette provided into either drive
A or B.
3. Click "Next" to let system search for an updated driver.
4. Click "Finish" to use the found driver.
5. Click "Ok" when prompted to insert the installation disk.
6. Change path to A:\ (or B:\) and click OK.
7. System will then automatically load all the necessary drivers and
files needed.
You might encounter some resource conflicts after loading the PnP
modem device (especially when there are non-Plug & Play adaptors installed
in your system). Please refer to Trouble-shooting section in Windows 95 for
further details.
Voice Features for MS5000-E
============================
Voice Support is available in terms of Answering Machine Playback &
Recording of Messages through Telephone Handset on most Telephony
Applications.
Note that the MS5000 Modem Card has no Handset support.
The Preferred device for Playback and Recording should be set to the
audio device. Checked the check box to use preferred devices only and
then click OK. Restart the system for preferred devices to take effect.
Setting Country for modem
=========================
1. Insert the installation diskette provided into drive A (or B).
2. Click "Start" button, then click on "Run".
3. At the "Open" prompt, type A:\ (or B:\), followed by the filename
SETCTRY.EXE and click OK.
4. Select the country of your choice and follow the instruction given.
Note that the default country setting is UK.
Modem AT Command Set
====================
The AT Command Instructions Set for the Modem hardware is now available
in Microsoft Word format (ATCOMSET.DOC). It is available in the software
diskette provided from manufacturer. This document has also been copied
into \Windows directory during installation.
Known Issues:
=============
1. Fax from ISDN is not supported.
2. The SETCTRY.EXE application is known to have problem with AZT2320
Sound Card driver. Should you require to change the country, please
use the PTHSP.EXE application instead. However, you will need to run
Hyperterminal (included with Win95 or any telephony application) and
issue the following AT modem command to re-init the modem in the new
setting. The AT command is as below:
AT&FS91=15S49=1&W0&W1
Things to Note :-
=================
1. MS5000-E can be set up on both WIN95 and WIN95(OSR2) but no support
on WIN3.x and DOS platform.
2. There is no handset support provided for the MS5000-E.
3. Windows Dos Terminal Emulation is not supported as yet. Applications
like Telix and NC Terminal Mode cannot be run in WIN95 Dos Emulation
Box.
4. Windows95 Software Modem driver version is 3.1604.
***********************************************************
* In case you encounter any problem with our products, *
* please quote the following model(s) when calling our *
* Technical Support : *
* MS5000-E Modem Card *
***********************************************************
------- The End ---------
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.