1. Iz2100ua.exe Driver
2. V90WIZ.INI File Contents

V90WIZ.INI Driver File Contents (Iz2100ua.exe)

;; V90 Wizard INI file for Zoom Modems Model 2819 and Model 2819A

[General]
FileCnt=4
ValidatorCnt=10
PostFlashCmdCnt=5
QuickCheckMode=1
BackupDone=0



[Options]
BlueScreen=5
OnePortOnly=0   ; faster testing if you set this to a modem port
ForceBackup=1    ;if 1, user can't get past the wizard page without backing up firmware
ShowTrace=0

LogoBmp=Zoomlogo.Bmp
OemAbout=For use with ZOOM INTERNAL modems Models 2819 and 2819A.  Zoom Telephonics, Inc.
OemAboutWebPage=Visit us on the web at www.zoomtel.com
OemAboutSupport=Tech Support Hotline: 1-617-423-1076
OemWarn=IMPORTANT: DO NOT Reset the modem.\n Click OK to start.
ShowAndWait=1
TimedShow=0
ShowIfItu=0

[Files]
;-----------------------------------------------------------------------
; filename, loadOrder, Flags, friendlyName[64], Description[256]
; Flags:  LOADER or UNLOADER or FIRMWARE
;  and:   TRANS or FINAL or BKUP (BKUP is added added by program)
;
; be sure to set [General] FileCnt=
; leading spaces are stripped
;
File01=XmUL003.s37,  1, LOADER,         Firmware Loader,      FlashLoader -- loads via XModem
File02=XmDL003.s37,  1, UNLOADER,       Firmware Unloader,    Used to make Firmware backup via XModem
File03=zoomec2f.s37, 2, FIRMWARE TRANS, V2.013A-A Flash Upgrade File., Firmware for Models 2819 and 2819A ONLY!
File04=zoomc96e.s37, 2, FIRMWARE FINAL, V2.100-A ITU V.90 Firmware,    V.90 Driver for Models 2819 and 2819A ONLY!

[Validators]
;-----------------------------------------------------------------------
; ATI3,op,Ati3Text,ugCode,Maker,Model,Remark
; op can be:=(equals), * (contains), ! (notContains),  et.al.
; ugCode can be: UPDATABLE, TRANS, FINAL, or UNKNOWN
;
; leading spaces are stripped
; be sure to set [General] ValidatorCnt=
;
Validator01=ATI3, =, ATI3, LOADFAULT, (Load Fault?), (Load Fault?), Maybe a modem in 'Load Fault' state
Validator02=ATI3, =, V0.516-K56_DLP-A Z201, UPDATABLE, Zoom, Zoom 2819, Looking for Dom DF (v0516-A) code
Validator03=ATI3, =, V1.002-K56_DLP-A Z201, UPDATABLE, Zoom, Zoom 2819, Looking for Dom DF (v1002-A) code
Validator04=ATI3, =, V1.142-K56_DLP-A Z201, UPDATABLE, Zoom, Zoom 2819, Looking for Dom DF (v1142-A) code
Validator05=ATI3, =, V1.140B2-K56_DLP-A Z201, UPDATABLE, Zoom, Zoom 2819, Looking for Dom DF Upgraded (v1140B2-A) code
Validator06=ATI3, =, V1.200-K56_DLP-A Z201, UPDATABLE, Zoom, Zoom 2819, Looking for Dom DF (v1200-A) code
Validator07=ATI3, =, V1.200-K56_DLP-H Z201, UPDATABLE, Zoom, Zoom 2819, Looking for Dom DF (v1200-H) code
Validator08=ATI3, =, V2.013A-K56_DLP-A Z201, TRANS, Zoom, Zoom 2819, Been updated to Transitional
Validator09=ATI3, =, V2.081-K56_DLP-A Z201, UPDATABLE, Zoom, Zoom 2819, Been updated to ITU v.90
Validator10=ATI3, =, V2.100-K56_DLP-A Z201, FINAL, Zoom, Zoom 2819, Been updated to ITU v.90

[PostFlashCmds]
;-----------------------------------------------------------------------
; Cmd##=type,AT_Cmd_Text
; ugCode can be: BKUP, TRANS, or FINAL
; Commands send after a flashload.  Usually start these with AT
; leading spaces are stripped, max len is 128 per command; max cmds: 10
; be sure to set [General] PostFlasCmdCnt=
;

Cmd01=BKUP,AT$$MF00338083
Cmd02=TRANS,AT$$MF00338083
Cmd03=FINAL,AT$$MF00338083
Cmd04=FINAL,ATZ
Cmd05=FINAL,AT