Accton SmartEnabler Installation FOR UNIXWARE History: 5/4/1995 v 1.0.3 1. SmartEnabler is now support UnixWare 1.1 as well as 2.0. 12/20/1995 v 1.0.4 1. SmartEnabler is now support UnixWare 1.1, 2.0 as well as 2.01. 2. SmartENabler now also supports EN2212 and EN2216 PCMCIA adapter cards. README.TXT This file Installation procedure file ACEN4UXW.TAR - Accton SmartEnabler driver UnixWare UNIX tar format CONTENTS ÄÄÄÄÄÄÄÄÄÄÄÄ 1.0 Installation for UnixWare SVR4.2 1.1 Install the SmartEnabler 1.2 Remove the SmartEnabler 2.0 Installation for UnixWare Enabler from tar file Appendix A: Configure the NE2K drivers for UNIXWARE. Configure UNIXWARE NE2K driver INSTALLATION FOR UNIXWARE SVR4.2 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 1.0 Installation for UnixWare 1.1 Install the SmartEnabler To install the Accton SmartEnabler for UnixWare a user needs to do the following: Insert the Accton SmartEnabler for UnixWare diskette in floppy drive 0 and type the following command to add the package to UNIXWARE: pkgadd -d/dev/dsk/f03dt <Enter> Next, select the go option to allow the installation utility of UnixWare to process the package. Wait until the installation process completes and then shutdown (reboot) the system to allow the new driver to run. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ NOTE: ³ ³ The Enabler requires a LAN card to be in place or plugged ³ ³ into a PCMCIA slot before booting the UnixWare. This version ³ ³ of the driver is only a virtual device driver, it is not a ³ ³ Socket Service or Generic enabler. Until Accton releases ³ ³ the Socket Service driver the user must follow this advice ³ ³ to make the LAN card work under UnixWare. ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ 1.2 Remove the SmartEnabler To remove the SmardEnabler from UnixWare SVR4.2, a user needs to do the following: 1.2.1 Logon as root and at the # prompt type: Pkgrm lsen <Enter> The user should see the following message: ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ lsen Accton SmardEnabler Driver Package v1.0.4 ³ ³ (i386)1.0.2 ³ ³ ³ ³ Do you want to remove this package [y.n.?.q]_ ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ 1.2.2 The user should type: "y" <Enter> Next the system informs the user that the package is being removed and updating system information. Finially, the user should see the following massages on the screen if the package is removed successfully: ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Removal of <lsen> was successful. ³ ³ ³ ³ *** IMPORTANT *** ³ ³ ³ ³ If removal of all desired packages is complete, the ³ ³ machine should be rebooted in order to ensure sane ³ ³ operation. Execute the shutdown command with the ³ ³ appropriate options and wait for the "Console Login:" ³ ³ prompt ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ 1.2.3 Finally the user should reboot the system to allow the new kernel to take effect. 2.0 Installation for UnixWare enabler from tar file 2.1 To install the Accton SmartEnabler from file to UnixWare: ----------------------------------------------------------- Steps to install the SmartEnable on the UnixWare platform: 1. Change to the /tmp directory via following command cd /tmp <Enter> 2. Copy the acen4uxw.tar file from the DOS diskette to /tmp directory: doscp a:acen4uxw.tar ./acen4uxw.tar.Z <Enter> 3. Uncompress the tar file uncompress acen4uxw.tar <Enter> 4. Change to the /usr/spool/pkg directory by issuing follow command cd /usr/spool/pkg <Enter> 5. Detar the file: tar xvf /tmp/acen4uxw.tar <Enter> 6. Run the pkgadd command as follows: pkgadd <Enter> 7. Follow the standard pkgadd installation procedure. Appendix A: Configure the NE2K drivers for UnixWare A-1 Configure NE2K driver for UNIXWARE A-2.1 Install the NE2K driver supplied by Novell. The driver must be installed at these specific I/O address and IRQ number: I/O base address = 0x300 (Hexdecimal) IRQ = 10 (Decimal)Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.