Accton Technology Corporation
Local Area Network Software Driver Support
NetWare* Client 32 for Windows* 95 and DOS/Windows 3.1x
======================================================================
Refer to the appropriate section for either the Windows* 95 or
DOS/Windows 3.1x Client 32 installation.
General Installation of Client 32 with Windows 95 using ACCTON's 32 bit LAN
driver
-------------------------------------------------------------------------
Prerequisites:
a. Windows 95 operating system installed.
b. NetWare Client 32 for Windows 95 archive file and any patch files.
c. Access to the Windows 95 CD or CAB files, since the Client 32
installation will ask for it.
1. If the ACCTON EN2216 adapter is being installed for the first
time when Client 32 is being added, install the adapter hardware as
described in the Installation Guide .
2. Run the SETUP.EXE program for Client 32. It is located in the
\PRODUCT\WIN95\IBM_ENU subdirectory of the Client 32 software.
3. On the NetWare Client 32 Installation screen, make sure the "Upgrade
NDIS driver to ODI, if available" box is checked if you are replacing
the NDIS driver with the ODI.
4. On the Recommended NetWare Client 32 properties screen, set the
appropriate settings for the version of NetWare you are using.
5. The Client 32 installation program will copy files. It may ask for the
source of the Windows 95 installation files. Click OK and then enter
the correct path to the files.
6. The Client 32 installation will finish, and you must reboot in order
for the changes to become effective.
General Installation of Client 32 with DOS/Windows 3.1x
------------------------------------------------------------------------
1. From the Novell NetWare Client 32 software, run INSTALL.EXE.
2. Select the NetWare Client 32 products you want to install from the on
your workstation from the list:
[X] NetWare Client 32 for DOS
[X] NetWare Client 32 for Windows
[ ] NetWare TCP/IP protocol stack[ ] NetWare IP (TCP/IP Required)
[ ] Desktop SNMP
[ ] HOSTMIB for SNMP (SNMP Required)
[ ] NetWare TSA for SMS
Note - "NetWare Client 32 for DOS" and "NetWare Client 32 for
Windows" are usually selected by default.
3. From the Customize Support for Windows menu, specify if you want to
use multiple country codes or if you want to set the shared Windows
path. The default for both of these is NO.
4. From the Select LAN Driver Type menu, select "32-bit LAN drivers".
Copy ACC16.LAN and ACC16.LDI onto a disk.
In the Novell installation process, select "USER SPECIFIED 32 BIT DRIVER."
5. From the Insert the Driver Disk menu, insert the disk with the
acc16.lan and acc16.ldi files, and then specify the path to those
files.
6. From the Installation Configuration Summary, verify the default
settings for Client 32 are correct, or modify as necessary.
Modify AUTOEXEC.BAT and CONFIG.SYS [YES]
Client Directory: C:\NOVELL\CLIENT32
Windows Directory: C:\WINDOWS
LAN driver type: 32-bit LAN drivers
LAN driver: ACCTON EN2216 PCMCIA Adapters
7. Novell NetWare will now copy the files to your workstations and
modify the configuration files to match your selected configuration.
Hints and Tips
--------------
1. Check for a LASTDRIVE statement in the CONFIG.SYS file. You must have
LASTDRIVE=Z in config.sys when using Client 32.
2. Verify that you have FIRST NETWORK DRIVE = <SOME DRIVER LETTER LESS THAN z>
in the NET.CFG file under the NetWare DOS Requester section.
NOTE: NET.CFG is position sensitive, so be careful to indent lines
with TWO spaceS or one tab as shown above in the example.
Sample Configurations
---------------------
Below are sample files from a Novell NetWare Client 32 workstation with an
ACCTON EN2216 PCMCIA adapter installed using the default
installation:
CONFIG.SYS
----------
DEVICE=C:\WINDOWS\HIMEM.SYS
DECICE=C:\WINDOWS\EMM386.EXE NOEMS X=D000-DFFF
DOS=HIGH,UMB
BUFFERS=30,0
FILES=60
LASTDRIVE=Z
DEVICEHIGH=C:\CARDSOFT\SSSIS.EXE /SKT:2
DEVICEHIGH=C:\CARDSOFT\CS.EXE
DEVICEHIGH=C:\CARDSOFT\CSALLOC.EXE
AUTOEXEC.BAT
------------
prompt $P$G
path=C:\WINDOWS;C:\DOS;C:\NOVELL\CLIENT32\
SET TEMP=C:\TEMP
@CALL C:\NOVELL\CLIENT32\STARTNET
STARTNET.BAT
------------
ACCOPEN.EXE <------------add by user
SET NWLANGUAGE=ENGLISH
C:\NOVELL\CLIENT32\NIOS.EXE
LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
LOAD C:\NOVELL\CLIENT32\CMSM.NLM
LOAD C:\NOVELL\CLIENT32\ETHERTSM.NLM
LOAD C:\NOVELL\CLIENT32\ACC16.LAN FRAME=ETHERNET_802.2 PCMCIA
LOAD C:\NOVELL\CLIENT32\ACC16.LAN FRAME=Ethernet_802.3 PCMCIA
LOAD C:\NOVELL\CLIENT32\ACC16.LAN FRAME=Ethernet_II PCMCIA
LOAD C:\NOVELL\CLIENT32\ACC16.LAN FRAME=Ethernet_SNAP PCMCIA
LOAD C:\NOVELL\CLIENT32\IPX.NLM
LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM
********************************************************************
NOTE: You must run accopen.exe prior startnet.bat loaded to activate
Accton EN2216 PCMCIA adapter. also you need card service and
socket service to support client 32.
Please see readme.txt at root directory for card service
and socket service installation.
********************************************************************
NET.CFG
-------
NetWare DOS Requester
FIRST NETWORK DRIVE F
NETWARE PROTOCOL NDS BIND
Protocol IPX
IPX SOCKETS 40
*Third-party trademarks are the property of their respective owners.
NOTE: The CIS on some EN2216 adapters may need to be upgraded for client32.
If you have trouble to load the client32 driver, please upgrade
the EN2216 CIS. You can get the tools from Accton web server
(http://www.accton.com.tw).
---End of File---
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.