///////////////////////////////////////////////////////////////// **** 05/25/04 **** Service Pack 3.00 **** New featured added **** \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ *** Pewin32Pro *** 1. Fixed JobRibbon Window Size. 2. Fixed Postion Window size not increased. 3. outstanding: sometimes pop access violation message up from watch window, when unplug usb cable. *** PmacTuningPro *** 1. Added a feature to support Turbo PC104 *** TurboSetupPro *** 1. Brush DC Motor is supported. *** P2Setup32Pro *** 1. Corrected the Current Feedback offset measurement. *** Pcomm32Pro *** 1. USB unplug works most time. 2. Fixed download PLC size to increase PLC stack size.(64K) 3. Fixed OpenServo buffer ploblem. 4. Fixed potential timeout condition at EThernet communication device 1-7. *** USB Driver *** 1. Include to support "CTRL+T" command. 2. changed "CTRL+Z" feature from 2 line to 1 line response. *** ISA Driver *** 1. Added support large DPRAM ///////////////////////////////////////////////////////////////// **** 08/18/03 **** Service Pack 2.00 **** New featured added **** \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ *** Pewin32Pro *** 1. Fixed JogRibbon Window, When you type +,- in Jog edit box, motor just run away. 2. Fixed Velocity value in position window, before servo time ratio is long value but corrected value is double( 2 to 2.25 ). *** PmacTuningPro *** 1. Fixed to type CTRL command in Terminal Window. 2. Fixed Current Loop Tuning for new firmware Ix70=0 and 100ms delay time. 3. Added detecting WatchDog and then stop sending GetResponse to Pmac. 4. Added DAC calibration, Auto, and Interactive tuning for PC104 Card. 5. Added Velocity and Acceleration Correlation in Parabolic Move Plot. 6. Added open and save Plot file function. 7. Added to support International version. *** TurboSetupPro *** 1. Fixed Current Loop Tuning for new firmware Ix70=0 and 100ms delay time. 2. Added to support MACRO 16 Axis. 3. Added to support International version. *** UmacConfigPro *** 1. Restore Control Word value after detected card. 2. Add Acc-69E,Acc-70E card to database. *** Pcomm32Pro *** 1. Fixed multi coordinate in binary rotaly buffer. 2. Fixed download "OPEN SERVO" over 3k file size. 3. Fixed Hang up at BootStrap Mode in serial communication ( add OVERLAPPED option ) 4. Added New Serial driver to support USB to Serial Converter. *** USB Driver *** 1. Added to support USB 2.0 ///////////////////////////////////////////////////////////////// **** 02/05/03 **** Service Pack 1.00 **** New featured added **** \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 1. Fixed language related decimal point issues. Latest update, supports the European language in the locales. "Comma vs dash". 2. Fixed encoder conversion table mistake in the Timebase and triggered timebase entry values and Fixed crash during download of a disjoint entry. 3. Removed "Kill the PmacServer after last application closes." Pmacserver now shuts down automatically within 5 minutes after the last application is closed. 4. Activated color code for all Active as well as (Reserve and internal) bits in the CS, Motor and Global status screens. 5. Updated configure/display of Servo IC related I-Variables. 6. In Program/PLCC upload screens, fixed crash due to close before the end of upload. 7. Added default color screens for (CS, Motor and Global) Status windows. 8. Fixed SAVE command delay issue in the Terminal Window 9. Fixed the CPU time hik issue upon opening Editor windows while certain programs requiring interface (e.g. Labview, Internet Explorer or OPCServer etc.) Driver related updates: 1. Fixed the return code for PmacSendLineA. Now all modes return number of characters upon successful transmission and COMM_FAIL otherwise. 2. For DPRAM supported modes added DPRSetWord and DPRGetWord for DeviceIOCall. 3. Fixed Interrupt Jump problem and thus fixed the crash. 4. Changed the DPRAM Detect routine. New method guarantees correct address for start of DPRAM in PMAC address space 5. Changed DPRSetDWord and DPRGetDWord to DPRSetWord and DPRGetWord. 6. Added support for uploading 16 axis MACRO station I-variables ///////////////////////////////////////////////////////////////// ***** 07/22/02 ****** Version 3.20 ****** NEW FEATURES ADDED ***** \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 1. Resource Manager added for managing the Macro definitions in any project. See Pewin32PRO Manual for detailed description. 2. Added DPR Viewer in the Main menu. It can be used to peek and poke any DPR in PMAC. 3. Added TCP mode of communication for Ethernot mode of communication. 4. USB is now supported by both Host port along with the DPRAM ASCII. 5. Added UMAC configurator in the Tool manager. 6. Driver Installation and troubleshooting instructions are bundled as a small manual and PDF document PComm32PRO_Install.pdf is now available in the c:\program files\DelTa Tau\Common folder. ///////////////////////////////////////////////////////////////// ***** 2/21/02 ***** Service Pack 3 ***** NEW FEATURES ADDED ***** \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 1. Editor is supported by a built-in Debugger for PLCs. 2. Ethernet Mode of communication is supported under all operating Systems including Windows NT 4.0. 3. Fixed false positive DPRAM bit for FLEX CPUs. 4. Implemented Encloder conversion table for Macro station. This is available in the configure menu. 5. Add Job ribbon to Pewin32PRO menu items. 6. Fixed the LN() statement bug in the PLCCs code in the PComm32.dll. 7. Please read the installation/configuration instructions PComm32PRO_Install.doc before using the package. The document is located in the Pewin32PRO installation forlder. ///////////////////////////////////////////////////////////////// ***** 12/11/01 ***** Service Pack 2 ***** NEW FEATURES ADDED **** \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ The latest updates of the Pewin32PRO Suite components are added in the form of a Service Pack. Service pack has been added to the release CD from now on. Service Pack is also be available on the web to anyone who wants to update his/her Pewin32PRO Suite components. Service Pack features include 1. It recognizes the licensed copy of any/all Pewin32PRO Suite components and updates them if needed. 2. It does not overwrite the trial version of any component so the trial versions of the Pewin32PRO Suite components will not be replaced. 3. Latest released version of the service pack is available at \\dt_vault\Released.SW\Pewin32 PRO\Service Packs\Release\ folder. Following updates are implemented in the Service Pack since last release of Pewin32PRO Suite 4. PComm32.DLL updates a. QMAC added in the PmacType b. Pmac2-PCI with Flex CPU (DPRAM mapping fixed) c. Pmac1-PCI interrupt implemented 5. Pewin32PRO Executive updates a. -Terminal changed to eliminate the scroll issue. -Memory corruption fixed for large queries in the terminal screen. -High speed buffer added to the Terminal screen options. -Terminal buffer contains 2000 lines and reduces the buffer to half automatically once the buffer is full. last half of the buffer is available so that user can view it. The buffer size can, however, be increased significantly to accommodate more viewable data. -History of previous commands is available and can easily be retrieved from the input window. If the first character matches the cursor automatically goes to the nearest matching command. b. Minimum update time limited to 100 msec for Serial/USB/Ethernet modes of communication c. Encoder conversion table for MACRO station added d. Limit of number of macro definitions for the Watch purposes is increased from 250 to 1000. The actual variable limit for EACH Watch window is still fixed to 250. e. Position window's Scaling and units display had an inefficient rollover routine. This routine has been fixed to a better algorithm which does not load the system for any rollover value. f. Fixed a crash caused by an undefined macro in the Editor window. 6. All Applications: QMAC changes in the PComm32.dll are reflected in the title of every application in PmacType. 30-day trial version is fully functional copy of Pewin32PRO Suite, which has all the latest service pack updates with only one limitation (Only 30-day trial per one computer) and is available on the Web and is accessible from the main page. ///////////////////////////////////////////////////////////////// ********* 10/11/2001 *********** PEWIN32PRO Version 3.1 ********* \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ ///////////////////////////////////////////////////////////////// ************************ FEATURES ******************************* \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ . Pewin32PRO is completely redesigned using VCL and latest software tools. Borland CBuilder 5.0 is used as the platform for development. PComm32 is compiled using Microsoft C++ 6.0. New features of the Pewin32PRO include interactive color editor, more versatile watch and position window. Further, variable configuration menus, particularly the M-variables, have been improved a lot for added features, as uploads, download and refresh etc. . The main expansion of the application is the ability of workspace. Workspace is saved in an INI file. this keeps track of all the open forms including their sizes, device association, update rate, state at the close of pervious session, and other related parameters as color, font and units and scales. Workspace can be edited outside the application for desired changes. Default workspace Pewin32PRO_default.ini is saved in the application folder. Name and location can be changed at any time. . Project manager is yet another added feature of Pewin32PRO. It allows for multiple files to be associated with a project (essentially associated with any one PMAC). Please browse for detailed project features. . Terminal is made smart to correctly keep track of previous commands. Status screens are modified to display the exact register and bit numbers for each item. . Choice of PMACSelect in each form is an added feature for versatility of the program. This allows for selection of any available device for any form with the need for a Terminal to be open. Further, the update period is selectable for most of the forms. ///////////////////////////////////////////////////////////////// ************************ KNOWN BUGS ***************************** \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ . Under Windows 98/ME when windows are maximized and one of them is closed the next window looses its borders. As of this version a temporary remedy to this is to either cascade the windows from windows menu or close and reopen the affected window. A permanent solution is being investigated. ///////////////////////////////////////////////////////////////// ************************ TERMINAL WINDOW ************************ \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ The following features have been added to the terminal window: 1. Terminal is polling PMAC for unsolicited response every 100 msec. 2. Terminal buffer contains 2000 lines and reduces the buffer to half automatically once the buffer is full. last half of the buffer is available so that user can view it. 3. History of previous commands is available and can easily be retrieved from the input window. If the first character matches the cursor automatically goes to the nearest matching command. *************** Bug Fixes ****************** Fixed the scroll problem in windows 98 *************** Wish List ****************** ///////////////////////////////////////////////////////////////// ************************ EDITOR WINDOW ************************** \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ The following features have been added to the editor window: 1. Syntax higlighting: The new editor is a colorized editor. all of the pmac variables, keywords, ... and any thing Else which is defined in the PMAC has its own color and font style. The user can also define his/her own color and font scheme. 2. Auto Correction: The new editor is capable of correcting and changing the code to a standard format. For example the following line of code will be corrected as following: before -> If (p1 != p3 And (p1+p3) < 5) after -> If (p1 != p3 And (p1+p3) < 5) 3. Auto Indentation: The new editor could auto indent the code base on the Tab size and the syntax of the code. For example the following line of code will be corrected as following: Before -> Open prog1 clear If (p1 != p3 And (p1+p3) < 5) p1=100 While (p3 = 0) q1=3 EndWhile EndIf Close After -> Open prog1 clear If (p1 != p3 And (p1+p3) < 5) p1=100 While (p3 = 0) q1=3 EndWhile EndIf Close 4. It has all the tools of a standard editor including copy, cut, paste, print, find/replace and print features. 5. The most important feature of this editor is its capability to open a file when an error occurs during the downloads. It supports inherited file such as include files and header files in addition to the main file. *************** Bug Fixes ****************** *************** Wish List ****************** 1. To construct a real-time online debugger for motion programs and PLCs/PLCCs. ///////////////////////////////////////////////////////////////// ************************ WATCH WINDOW *************************** \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ The following features have been added to the watch window: 1. Adding multiple Variables: In the new version of the watch window, the user can add multiple variables, which it includes the macro variables too. 2. Support for 48 bit words: Watch window can now support 48 bit words, to view 48 bits of a word, the user should look at the word in the binary mode. The default start bit index now starts from bit 0 to match PMAC bit numbers. *************** Bug Fixes ****************** 1. On users' demand, the number of macro definitions has been increased from 250 to 1000 for each watch window. The maximum number of variables is still limited to 250. *************** Wish List ****************** 1. Add watch for control characters such as ^P, ^B etc. 2. ///////////////////////////////////////////////////////////////// ************************ POSITION WINDOW ************************ \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ The following features have been added to the new position window 1. All Position, Velocity, and Error are displayed in one window and can be made visible separate as well. 2. For Turbo PMACS position display for all 32 motors is also available. 3. The added feature of visible/hide of any motor for all position windows is available. It can be invoked from the units and scales form. The information about visible/hide motors is also saved in the configuration file for future sessions. *************** Bug Fixes ****************** ///////////////////////////////////////////////////////////////// ************************ STATUS WINDOWS ************************* \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ Following status windows are described in this section: Program status, PLC status, PLCC status, Connector status, Motor status, Coordinate system status, Global status and Motor Status Summary. 1. All of the motor and coordinate system status can be changed to next motor/ CS by pgUp/PgDw keys. *************** Bug Fixes ****************** *************** Wish List ****************** ///////////////////////////////////////////////////////////////// ************************ CONFIGURE WINDOWS ********************** \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ This section covers configuration of all variable(I, P, Q, M) screen, C.S. and Encoder conversion tables. *************** Bug Fixes ****************** . Fixed UMAC (ACC-51E) Encoder conversion table download issues. *************** Wish List ****************** ///////////////////////////////////////////////////////////////// ********** WORKSPACE AND PROJECT MANAGER ************************ \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ This section covers the features related to Workspace, Project manager and related menu items. 1. Workspace manages the configuration of Pewin32PRO. It keeps track of dimensions/units/color/fonts of all child windows. It further it keeps track of open windows and their associated devices, update rate, etc. 2. Project manager is responsible for holding project files for one or more PMAC devices. A project can be associated with any configured PMAC device and downloaded on demand. A project containing multiple files downloads all the associated files. Associated files can be edited or downloaded individually as well. 3. Message windows display the results of download/upload. or cancellation if aborted. Download errors are listed along with file names and corresponding line numbers. Once clicked Pewin32RPO will open the correct file, and highlight the actual line number. *************** Bug Fixes ****************** . Insert and delete conflicts with the watch window have been removed. *************** Wish List ****************** ///////////////////////////////////////////////////////////////// ************************ OTHER MENU ITEMS *********************** \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ This section covers configuration of all variable(I, P, Q, M) screen, C.S. and Encoder conversion tables along with Backup/Restore and other PMAC Tools. *************** Bug Fixes ****************** . Fixed UMAC (ACC-51E) Encoder conversion table download issues. *************** Wish List ****************** . Add the Motor Upload/Restore/verify routines. . Add Macro Upload/Restore/Verify routines.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.