SPECIFICATIONS AccelePort USB 2 Module Specifications Power Requirements The USB 2 module is powered from the USB bus that connects it to the the host computer. Each module draws: 10 milliamps maximum (suspend mode) 100 milliamps maximum (power-up mode) 200 milliamps maximum (active mode) Environmental Ambient temperature 10 to 40 degrees C Relative humidity 5% to 90% Altitude 0 to 12,000 feet Serial Interface Surge Protection 15 kilovolts per IEC 1000-4-2, Level 4 Dimensions Length 4 inches Width 2.4 inches Height 1 inch Weight 0.4 pounds USB Cable length 6 feet AccelePort USB 4 and USB 4 EIA422 Module Specifications Power Requirements The USB 4 module is powered from the USB bus that connects it to the the host computer. Each module draws: 10 milliamps maximum (suspend mode) 100 milliamps maximum (power-up mode) 200 milliamps maximum (active mode) Environmental Ambient temperature 10 to 40 degrees C Relative humidity 5% to 90% Altitude 0 to 12,000 feet Serial Interface Surge Protection 15 kilovolts per IEC 1000-4-2, Level 4 Dimensions Length 6.3 inches Width 3.75 inches Height 1.2 inches Weight 0.5 pounds USB Cable length 6 feet AccelePort USB 8 Module Specifications Power Requirements The USB 8 module is powered by an auxiliary power unit provided with the module. It draws no power from the USB bus. Each module draws: 500 milliamps maximum Up to 500 milliamps of additional current will be drawn for each downstream USB port which is used by a bus-powered USB device. Environmental Ambient temperature 10 to 40 degrees C Relative humidity 5% to 90% Altitude 0 to 12,000 feet Serial Interface Surge Protection 15 kilovolts per IEC 1000-4-2, Level 4 Dimensions Length 8.1 inches Width 4.5 inches Height 1.5 inches Weight 0.9 pounds Power unit weight 0.3 pounds USB Cable length 6 feet REGULATORY NOTICES AccelePort USB 2 AccelePort USB 4 AccelePort USB 4 EIA422 AccelePort USB 8 The above listed products comply with the following standards, as detailed below: FCC Part 15 Class B ICES 003 Class B EN55022 Class B EN50081-1 EN50082-2 FCC (Federal Communications Commission) Statements FCC Part 15 Class B Radio Frequency Interference (RFI) (FCC 15.105) This equipment has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15, Subpart B of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Labeling Requirements (FCC 15.19) This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications (FCC 15.21) Changes or modifications to this equipment not expressly approved by Digi may void the user=92s authority to operate this equipment. Cables (FCC 15.27) Shielded cables must be used to remain within the Class B limitations. Declaration of Conformity In accordance with FCC Dockets 96-208 and 95-19 Digi International declares that the product: Manufacturer=92s Name: Digi International Inc. Corporate Headquarters: 11001 Bren Road East, Minnetonka MN 55343 Manufacturing Headquarters: 10000 West 76th Street, Eden Prairie MN 55344 Product Name Model # AccelePort USB 2 70001417 AccelePort USB 4 70001419 AccelePort USB 4 EIA422 70001421 AccelePort USB 8 70001418 The products listed have been tested at an External Test Laboratory certified per FCC rules and have been found to meet the FCC, Part 15, Class B, Emission Limits. Documentation is on file and available from the Digi International Homologation Department. ICES (Industry Canada Compliance Statements) 003 Class B This Class B digital apparatus meets the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil num=E9rique de la Classe B respecte toutes les exigences du R=E8glement sur le mat=E9riel brouilleur du Canada.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.