#
| README file for
|
| ELSA graphics driver for Windows 2000 build 2195
|
| Version: 5.12.10.236
|
| Synergy II
|
| Copyright (c) 2000 ELSA AG (Aachen, Germany)
|
| ELSA AG Internet : http://www.elsa.de
| Sonnenweg 11
| 52070 Aachen
| Germany
|
| ELSA Inc. Internet : http://www.elsa.com
| 1630 Zanker Road
| San Jose, CA 95112
| USA
|
| ELSA Asia Inc. Internet : http://www.elsa.com
| 7F-11, No. 188, Sec. 5
| Nanking East Road
| Taipei 105
| Taiwan, R. O. C.
|
| ELSA Japan Inc. Internet : http://www.elsa.com
| Mita Suzuki Building 3F
| 5-20-14 Shiba, Minato-ku
| Tokyo 108-0014
| Japan
|
| 2000-06-30, CBuersch
1 Driver Description
2 Installation Instructions
3 Additional Configuration Options
4 Known Bugs / Restrictions
5 Troubleshooting
-------------------------------------------------------------------
1 Driver Description
Display Driver Version : 5.12.10.236
OpenGL Driver Version : 5.12.10.236
Operating System : Windows 2000
Display adapter : ELSA Synergy II
Supported Languages : no limitations
1.1 List of file names (files may be compressed)
- esynii.cat (Catalog file)
- esynii.inf (Script file for driver installation)
- esyniid.dll (Display driver)
- esyniim.sys (Miniport driver)
- esyniio.dll (OpenGL driver)
- readme.txt (the file you are reading)
- liesmich.txt (german version of the file you are reading)
- \ELSAINFO\ (ELSAINFO directory )
- \GLSET\ (APPLICATION SETTINGS directory)
-------------------------------------------------------------------
2 Installation instructions
2.1 Preparation
Note: If there were already other GLint based boards
installed, their referring "oemx.inf" and
"oemx.pnf" files (where "x" read as numbers) in
the INF subdirectory of your system have to be
deleted. This is to ensure that the Plug&Play
recognition of Windows 2000 is working properly.
Copy all listed driver files to a formatted disk (or a
temporary directory). Uninstall all display adapter devices
under CONTROL PANEL/SYSTEM/HARDWARE/DEVICE MANAGER/DISPLAY
ADAPTERS. Remove your floppy disk and reboot your system.
2.2 Installation
Windows 2000 uses Plug&Play functions to recognize your
display adapter. Here is how:
1. Device recognized. The "Found New Hardware" wizard
will guide you.
- click "Next" - choose option
"Display a list of the known drivers ..."
- click "Next"
- choose "Display Adapters"
- click "Next"
- click "Have Disk..."
- choose the directory from (2.1)
- click "Ok"
- choose entry "ELSA Synergy II
- click "Next"
- click "Next"
- click "Yes".
Now the driver will be installed.
- click "Finish.
2. The installtion of the display driver is finished now.
Remove your floppy disk and reboot your system now.
Note: Depending on your monitor at the next reboot
Plug&Play will recognize and install a monitor
device.
2.3 Verification
Open CONTROL PANEL/DISPLAY/SETTINGS. Verify that you can
read "Plug and Play Monitor on ELSA Synergy II".
You should now be able to use a resolution higher than
800x600.
2.4 Adjusting Refresh Frequencies
Click "Advanced" Button on Display Properties Page. Go to
Monitor Properties Page and use the DropDown-List "Refresh
Frequency".
-------------------------------------------------------------------
3 Additional Configuration Options
3.1 Additional Tools
3.1.1 ELSA Application Settings
The ELSA Application Settings allow you to configure the 3D
options of your ELSA GLoria graphics board. You will find
this tool as a tab in the display properties.
You also will find a detailed description by clicking the
Help key.
3.1.2 ELSA Info
ELSA Info offers a quick view of all relevant information
about your hard- and software configuration. First of all,
this is a diagnostic tool, which should help you in solving
configuration problems of your graphics system.
You can redirect all shown information to file or printer.
The generated output will be helpful in getting quick
and efficient support from ELSA.
-------------------------------------------------------------------
4 Known Bugs / Restrictions
-------------------------------------------------------------------
5 Troubleshooting
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.