1. MCCDrivers.zip Driver
2. cbercode.txt File Contents

cbercode.txt Driver File Contents (MCCDrivers.zip)

0 1 {No error has occurred}
1 0 {Invalid board number}
2 0 {Digital device is not responding - Is base address correct?}
3 0 {Counter device is not responding - Is base address correct?}
4 0 {D/A is not responding - Is base address correct?}
5 0 {A/D is not responding - Is base address correct?}
6 0 {Selected board does not have digital I/O}
7 0 {Selected board does not have a counter}
8 0 {Selected board does not have a D/A}
9 0 {Selected board does not have an A/D}
10 0 {Selected board does not have thermocouple inputs}
11 0 {Invalid digital port number}
12 0 {Invalid counter device}
13 0 {Invalid D/A device}
14 0 {Invalid sample mode}
15 0 {Board configured for invalid interrupt level}
16 0 {Invalid A/D channel number}
17 0 {Invalid count}
18 0 {Invalid counter configuration specified}
19 0 {Invalid D/A value}
20 0 {Invalid D/A channel number}
21 0 {Invalid error code}
22 0 {Background operation already in progress}
23 1 {DMA transfer crossed page boundary, may have small gap in data}
24 0 {Invalid sampling rate}
25 0 {Board switches set for Compatible mode}
26 1 {Incorrect initial trigger state - D0 must start at TTL low}
27 0 {A/D is not responding}
28 1 {Trigger occurred before requested number of samples were collected}
29 1 {Data overrun - data was lost}
30 0 {Invalid voltage (or current) range}
31 1 {This A/D board does not have programmable gain}
32 0 {Specified file name is not valid}
33 1 {Disk is full, could not complete operation}
34 1 {Board switch set to compatible mode - sampling speed may be limited}
35 0 {Pointer is not valid}
36 0 {Too many gains}
37 1 {Sample rate may be too fast for SINGLEIO mode}
38 0 {CONVERTDATA cannot be used with DMA I/O and BACKGROUND}
39 0 {Board does not support DTConnect option}
40 0 {CONTINUOUS can only be run with BACKGROUND}
41 0 {This function can not be used with this board}
42 0 {Digital port not configured correctly for requested operation}
43 1 {This digital port is not configurable (its an In/Out port)}
44 0 {Invalid digital port configuration}
45 0 {First point number is not valid}
46 0 {Attempted to read past the end of the file}
47 0 {This board does not have 8254 counter}
48 0 {This board does not have 9513 counter}
49 0 {Invalid trigger type}
50 0 {Trigger value greater than maximum allowed}
51 0 {Invalid error code}
52 0 {Invalid option specified for this function}
53 0 {Invalid pre-trigger count specified}
55 0 {Invalid FoutDivider value}
56 0 {Invalid FoutSource value}
57 0 {Invalid compare value}
58 0 {Invalid TimeOfDay value}
59 0 {Invalid GateInterval value}
60 0 {Invalid GateControl value}
61 0 {Invalid CounterEdge value}
62 0 {Invalid SpecialGate value}
63 0 {Invalid Reload value}
64 0 {Invalid RecycleMode value}
65 0 {Invalid BCDMode value}
66 0 {Invalid CountDirection value}
67 0 {Invalid OutputControl value}
68 0 {Invalid BitNum specified}
69 0 {None of the counter channels were enabled}
70 0 {An element of CntrControl array not set to DISABLED or ENABLED}
71 0 {Invalid EXP channel specified}
72 0 {Board set to wrong A/D range for reading thermocouples}
73 1 {Temperature input is out of range}
74 0 {Invalid temperature scale specified}
75 0 {Invalid error code}
76 0 {Specified board does not have chan/gain queue}
77 0 {Count must be > packet size to use Continuous mode}
78 1 {The FIFO went empty while doing output}
79 0 {Invalid memory mode specified}
80 1 {Measured frequency too high for selected gating interval}
81 0 {A CJC channel must be configured to make temperature measurements}
82 0 {Invalid ChipNum specified}
83 0 {The digital I/O on this board is not enabled}
84 1 {CONVERT option can not be used with 16 bit A/D converters}
85 0 {The EXTMEMORY option requires that a memory board be attached to A/D}
86 0 {No memory read/write allowed while DT transfer in progress}
87 0 {The specified board is not a memory board}
88 0 {The first chan in scan and number of chans must be even (0,2,4 etc)}
89 0 {Counter was not configured or initialized}
90 0 {This board does not have an 8536 counter chip}
91 1 {Board does not time A/D sampling. Collecting at fastest possible speed}
92 0 {Operation interrupted with CTRL-C key}
93 0 {No selector could be allocated}
94 1 {This board does not support Burst Mode}
95 0 {This function not available in Windows library}
96 1 {Board not configured for SIMULTANEOUS option}
97 0 {An even chan is in an odd slot in queue (or vice versa)}
98 1 {Sampling speed (>625 kHZ) to system memory MAY be too fast for counts > 1024}
99 0 {Selected board is not a RS-485 board}
100 0 {This function not available in DOS library}
101 1 {Bipolar and Unipolar ranges can not be used together in A/D queue}
102 0 {Sampling rate is too high for clock speed, change clock jumper on board}
103 1 {Calibration factors are invalid - Disabling software calibration}
104 0 {Invalid configuration information type specified}
105 0 {Invalid configuration item specified}
106 0 {Cannot access the PCMCIA board}
107 0 {Board does not support background operation}
108 1 {The string argument is too short for the string being returned}
109 0 {CONVERTDATA not allowed with EXTMEMORY option}
110 0 {Program error - bad values used in cbFromEngUnits or cbToEngUnits}
111 1 {Rates greater than 125 KHz must use on board 10 MHz clock}
112 1 {Desired sample rate is below hardware minimum}
113 0 {Invalid error code}
114 0 {More than one temperature sensor type defined for EXP-GP}
115 0 {No temperature sensor type defined for EXP-GP}
116 1 {Selected 12 bit board already returns converted data}
117 1 {CONTINUOUS mode cannot be used with EXTMEMORY}
118 1 {cbAConvertPretrigData called after cbAPretrig failed}
119 0 {Bad counter arg passed to cbCLoad}
120 0 {Low trigger threshold is greater than high threshold}
121 0 {NO PCM Card was found in the specified slot}
122 0 {Two identical PCM cards found.  Please specify exact slot in Instacal.}
123 0 {Invalid sensor type selected in Instacal}
124 0 {Tried to delete a board that does not exist}
125 0 {Cannot find the board name file}
126 0 {Cannot find CB.CFG file}
127 0 {The CBUL.386 virtual device driver is not installed}
128 0 {The requested amount of Windows page-locked memory is not available}
129 0 {Not enough DOS memory available}
130 0 {Obsolete option specified for cbSetConfig/cbGetConfig}
131 0 {No registry entry for this PCMCIA board}
132 0 {CBUL32.SYS device driver is not installed}
133 0 {No DMA memory available to device driver}
134 0 {The selected interrupt is not available}
135 0 {This board does not have an LS7266 counter chip}
136 0 {Invalid Quadrature arg passed to cbC7266Config()}
137 0 {Invalid CountingMode arg passed to cbC7266Config()}
138 0 {Invalid DataEncoding arg passed to cbC7266Config()}
139 0 {Invalid IndexMode arg passed to cbC7266Config()}
140 0 {Invalid InvertIndex arg passed to cbC7266Config()}
141 0 {Invalid FlagPins arg passed to cbC7266Config()}
142 0 {This board does not support cbCStatus()}
143 0 {Gating may not be used when indexing is enabled}
144 0 {Indexing not allowed in non-quadrature mode}
145 0 {Temperature input has open connection}
146 0 {Count must be integer multiple of packet size for Continuous mode}
147 0 {Invalid callback function specified}
148 0 {MetraBus in use}
149 0 {MetraBus I/O card has no configured controller card}
150 0 {Invalid event type specified for this board}
151 0 {An event handler has already been enabled for this event type}
152 0 {Invalid event count specified}
153 0 {Unable to install event handler}
154 0 {Buffer is too small for operation}
155 0 {Invalid analog input mode (single-ended vs differential) specified}
156 0 {Invalid signal type specified}
157 0 {Invalid connection specified}
158 0 {Invalid index specified. If index>0, then you've reached end of internal list.} 
160 0 {Count cannot be greater than the FIFO size for BURSTIO mode. Furthermore, Count must be integer multiple of number of channels in scan.}
161 0 {Device has stopped responding. Please check connections.}
163 0 {Required access or privilege not acquired for specified operation. Please check for other users of device and restart application.}
164 1 {Device unavailable at time of request. Please repeat operation.}
165 1 {Device is not ready to send data. Please repeat operation.}
168 1 {There was a network error. Please check network connections, repeat operation and/or restart application.}
169 0 {The specified bit is used for alarm.}
170 0 {One or more bits on the specified port are used for alarm.}

200 0 {Internal error occurred in library}
201 0 {DMA buffer could not be locked}
202 0 {DMA already controlled by another driver}
203 0 {Invalid Windows memory handle}

304 0 {Error reading from configuration file}
305 0 {Error writing to configuration file}
308 0 {Cannot open configuration file}
325 1 {Overflow of RTD conversion}
326 0 {PCI BIOS not present on the PC}
327 0 {Specified PCI board not detected}
328 0 {Specified PCI board not detected}
334 0 {Cannot install interrupt handler. IRQ already in use}
339 0 {Unable to access Card Information Structure}
343 0 {Specified USB board not detected}
344 0 {No more files in the directory}
345 0 {No file exists for the specified file number}
346 1 {The structure size is invalid}
347 0 {This file may not contain all of the data from the logging session because the logging session was not terminated properly}
348 0 {File is not a valid MCC binary file}
349 0 {Invalid delimiter specified for CSV file extension}

401 0 {PCMCIA Card and Socket Services Error - Invalid Adapter}
402 0 {PCMCIA Card and Socket Services Error - Invalid Attribute}
403 0 {PCMCIA Card and Socket Services Error - Invalid base system memory address}
404 0 {PCMCIA Card and Socket Services Error - Invalid EDC Generator}
406 0 {PCMCIA Card and Socket Services Error - Invalid IRQ Level}
407 0 {PCMCIA Card and Socket Services Error - Invalid Card Offset}
408 0 {PCMCIA Card and Socket Services Error - Invalid Page}
409 0 {PCMCIA Card and Socket Services Error - Incomplete read request}
410 0 {PCMCIA Card and Socket Services Error - Invalid Window size}
411 0 {PCMCIA Card and Socket Services Error - Invalid Socket}
413 0 {PCMCIA Card and Socket Services Error - Invalid Window type}
414 0 {PCMCIA Card and Socket Services Error - Invalid VCC level}
415 0 {PCMCIA Card and Socket Services Error - Invalid Vpp1 or Vpp2 level}
417 0 {PCMCIA Card and Socket Services Error - Invalid Windows}
418 0 {PCMCIA Card and Socket Services Error - Incomplete write request}
420 0 {PCMCIA Card and Socket Services Error - No card present}
421 0 {PCMCIA Card and Socket Services Error - Service not supported}
422 0 {PCMCIA Card and Socket Services Error - Invalid Mode}
423 0 {PCMCIA Card and Socket Services Error - Invalid Speed}
424 0 {PCMCIA Card and Socket Services Error - Busy}
425 0 {PCMCIA Card and Socket Services Error - Undefined Error}
426 0 {PCMCIA Card and Socket Services Error - Write protect failure}
427 0 {PCMCIA Card and Socket Services Error - Argument length invalid}
428 0 {PCMCIA Card and Socket Services Error - Argument invalid}
429 0 {PCMCIA Card and Socket Services Error - Configuration has been locked}
430 0 {PCMCIA Card and Socket Services Error - Resource in use}
431 0 {PCMCIA Card and Socket Services Error - No more of the requested items available}
432 0 {PCMCIA Card and Socket Services Error - Card services is out of resources}
433 0 {PCMCIA Card and Socket Services Error - Invalid handle}
434 0 {PCMCIA Card and Socket Services Error - Client Version Not Supported}

501 0 {Invalid DOS function number specified - *** Internal Error}
502 0 {Cannot find file}
503 0 {Cannot find path}
504 0 {No DOS handles left}
505 0 {File Access denied}
506 0 {Invalid handle - *** Internal Error}
507 0 {DOS has no more memory available}
515 0 {Invalid disk drive}
518 0 {Too many disk files}
519 0 {Disk is write protected}
521 0 {Disk drive is not ready}
525 0 {DOS seek error}
529 0 {DOS write error}
530 0 {DOS read error}
531 0 {DOS general fault}

603 0 {Cannot enable interrupt.  IRQ already in use.}
605 0 {Cannot disable interrupts}
606	0 {Insufficient memory to page lock data buffer}
630 0 {PCM card not detected}

801 0 {The number of elements in the gain array must equal the number of channels in the scan}
802 0 {The length of dimension 0 in the data array must equal the number of channels in the scan}
-2 {}