;*********************************************************************** ; ; Network card and driver SETUP INF file. ; ; OEMSETNET.INF ; ;*********************************************************************** [Identification] OptionType = NetAdapter [PlatformsSupported] ISA EISA "Jazz-Internal Bus" ;;+ Andge PCMCIA ;;- [OptionsNT4] ComboCard [OptionsNT3] ComboCard ComboCardA ;*********************************************************************** ; CONSTANTS FOR USING DIALOGS ;*********************************************************************** ; ; File names, etc. ; [AllFileConstants] UtilityInf = "UTILITY.INF" ParamInf = "NCPARAM.INF" subroutineinf = "SUBROUTN.INF" SoftwareType = "driver" Exit_Code = 0 NetEventDLL = "%SystemRoot%\System32\netevent.dll" IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll" Manufacturer = "Microsoft" ProductMajorVersion = "3" ProductMinorVersion = "1" ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion) [FileConstants] GenericInfVersion = "v1.0" GenericAdapterName = "PLANET ENW-3503 Ethernet Fax/Modem Card" GenericDriverName = "PLANET ENW-3503 Ethernet Fax/Modem NDIS Driver" GenericFunctionName = "PCMCIA Combo Card" GenericSysName = "LMNDIS.SYS" GenericName = "ComboCard" ProductSoftwareName = "ComboCard" NetRuleSoftwareType = "ComboCardSys ndisDriver ComboCardDriver" NetRuleSoftwareUse = $(SoftwareType) NetRuleSoftwareBindForm = """ComboCardSys"" yes no container" NetRuleSoftwareClass = {"ComboCardDriver basic"} NetRuleSoftwareBindable = {"ComboCardDriver ComboCardAdapter non exclusive 100"} ProductHardwareName = "ComboCard" NetRuleHardwareType = "ComboCard ComboCardAdapter" NetRuleHardwareBindForm = " yes yes container" NetRuleHardwareClass = {"ComboCardAdapter basic"} ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion" ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters" PCCardDataBase = $(!NTN_ServiceBase)"\Pcmcia\DataBase" NICDataBase = $(PCCardDataBase)"\PCMCIAs\ComboCard" CardwizDataBase = $(!NTN_ServiceBase)"\resman\MacDataBase" CWZNICDataBase = $(CardwizDataBase)"\PCMCIAs\ComboCard" ;+ Kenny 10/20'98 NICDataBase2 = $(PCCardDataBase)"\PCMCIAs\LanModem" CWZNICDataBase2 = $(CardwizDataBase)"\PCMCIAs\LanModem" ;- Kenny 10/20'98 [GeneralConstants] from = "" to = "" ExitCodeOk = 0 ExitCodeCancel = 1 ExitCodeFatal = 2 KeyNull = "" MAXIMUM_ALLOWED = 33554432 RegistryErrorIndex = NO_ERROR KeyProduct = "" KeyParameters = "" ;;+ 1-12-1996 Andge KeyPCCard = "" KeyDataBase = "" ;;- NT400VersionConstant = "(4.0)" TRUE = 1 FALSE = 0 NoTitle = 0 ExitState = "Active" OldVersionExisted = $(FALSE) DriverPath = $(!STF_NTPATH)\drivers [date] ; Now is a list which contains { Sec from 1-1-1970, Year, Month, Day, Hour, ; Minute, Second } Now = {} ? $(!LIBHANDLE) GetSystemDate [Identify] ; ; read-syms Identification set Status = STATUS_SUCCESSFUL set Identifier = $(OptionType) set Media = #("Source Media Descriptions", 1, 1) set STF_DISPLAYDEBUGOUTPUT = 1 Return $(Status) $(Identifier) $(Media) $(STF_DISPLAYDEBUGOUTPUT) [ReturnOptions] ; ; set Status = STATUS_FAILED set OptionList = {} set OptionTextList = {} ; ; Check if the language requested is supported ; set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) in $(LanguageList) ; ; Check if the platforms requested is supported ; ifstr(i) $($1) == "" goto returnoptions endif set PlatformList = ^(PlatformsSupported, 1) Ifcontains(i) $($1) in $(PlatformList) goto returnoptions else set Status = STATUS_NOTSUPPORTED goto finish_ReturnOptions endif else set Status = STATUS_NOLANGUAGE goto finish_ReturnOptions endif ; ; form a list of all the options and another of the text representing ; returnoptions = + set NT_VER = "NT3" OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Enum" $(!REG_KEY_READ) KeyNT ifstr $(KeyNT) == $(KeyNull) goto readoptions endif CloseRegKey $(KeyNT) set NT_VER = "NT4" readoptions = + set OptionList = ^(Options$(NT_VER), 1) set OptionTextList = ^(OptionsText$($0)$(NT_VER), 1) set Status = STATUS_SUCCESSFUL finish_ReturnOptions = + Return $(Status) $(OptionList) $(OptionTextList) [InstallOption] ; ; Set default values for ; set Status = STATUS_FAILED ; ; extract parameters ; set Option = $($1) set SrcDir = $($2) set AddCopy = $($3) set DoCopy = $($4) set DoConfig = $($5) ; ; Check if the language requested is supported ; set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) NOT-IN $(LanguageList) Return STATUS_NOLANGUAGE endif set-subst LF = "\n" read-syms GeneralConstants read-syms AllFileConstants read-syms FileConstants read-syms DialogConstants$(!STF_LANGUAGE) ifstr(i) $(!NTN_Origination) == "NCPA" set Continue = $(OK) endif read-syms FileConstants$(!STF_LANGUAGE) detect date set-title $(FunctionTitle) set to = Begin set from = Begin ; ; Assume all is well. ; set CommonStatus = STATUS_SUCCESSFUL EndWait ; ; Set up the operation-mode-based variables and gaily welcome ; the user. If the "install mode" variable is improperly set, ; assume this is a new installation. ; Begin = + set CurrentVersionValue = "" OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows Nt\CurrentVersion" $(!REG_KEY_READ) KeyNt Ifstr(i) $(KeyNt) != "" GetRegValue $(KeyNt) "CurrentVersion" CurrentVersionValue CloseRegKey $(KeyNt) Endif ifstr(i) (*($(CurrentVersionValue),4)) == $(NT400VersionConstant) set NT_VER = NT4 OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Enum\Root\LEGACY_PCMCIA\0000" $(!REG_KEY_READ) KeyPCMCIA Ifstr(i) $(KeyPCMCIA) != "" GetRegValue $(KeyPCMCIA) "StatusFlags" PCMCIAFlag CloseRegKey $(KeyPCMCIA) set PCMCIAStatusFlag = *($(PCMCIAFlag), 4) Endif ifint $(PCMCIAStatusFlag) == 8 set ProductSoftwareImagePath = "\SystemRoot\System32\drivers\LMNDISA.SYS" else set ProductSoftwareImagePath = "\SystemRoot\System32\drivers\LMNDIS.SYS" endif else set ProductSoftwareImagePath = "\SystemRoot\System32\drivers\LMNDIS.SYS" set NT_VER = NT3 endif Set ActivateDetection = FALSE Ifstr(i) $(!NTN_InstallMode) == deinstall set StartLabel = removeadapter else-Ifstr(i) $(!NTN_InstallMode) == Update set StartLabel = UpgradeSoftware else-Ifstr(i) $(!NTN_InstallMode) == bind set StartLabel = bindingadapter else-Ifstr(i) $(!NTN_InstallMode) == configure ; set ActivateDetection = TRUE set StartLabel = configureadapter ; ; You cannot config the software component ; Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Debug-Output "Cannot configure the driver software." Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif set Error = $($R0) set from = end set to = end goto nonfatalinfo endif else ; set ActivateDetection = TRUE set StartLabel = installadapter set OEM_ABANDON_OPTIONS = {} set OEM_ABANDON_SOFTWARE = FALSE set OEM_ABANDON_ON = TRUE endif ; set the default values ; IRQ Level = 11 set IRQValue = *($(IRQList), 7) ; IOBase Address = 0x320 set IOBaseAddrValue = *($(IOBaseAddrList), 2) ;Kenny ;* IoBase Address for Modem * set ModemIOBaseAddressValue = *($(ModemIOBaseAddressList), 3) ; IOBase Address = 0x2F8 ; Memory Address = 0xd0000 set MemAddrValue = *($(MemAddrList), 1) ; COM Port = 3 set ComPortValue = *($(ComPortList), 2) ; COM IRQ = 5 set ComIrqValue = *($(ComIrqList), 4) Set from = $(fatal) Set to = $(fatal) Goto $(StartLabel) ;----------------------------------------------- ; Installation Section ;----------------------------------------------- installadapter = + ; ; First, check whether the same version of the software exists ; OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) ; ; Same version already existed in the local machine ; Popup the dialog and ask the user whether he wants to continue ; CloseRegKey $(KeyProduct) ifstr(i) !(NTN_RegBase) == $(ProductKeyName) ; ; Cannot Install the same software again ; Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+ $(ProductVersion) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif goto end else ; ; Add a new adapter card? ; Shell $(UtilityInf), CardExistedDlg ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif ifstr(i) $($R1) != "OK" goto end endif set OldVersionExisted = $(TRUE) endif endif ; ; dll load addition ; Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1)WINNT\ install "Install-Dll" goto adaptersetup ;----------------------------------------------- ; Configuration Section ;----------------------------------------------- ; ; Get the current values of all the parameters ; configureadapter = + Ifstr $(KeyProduct) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find component product key" goto fatalregistry Endif Endif ; ; Get the other parameters; they're attached to the service parameters key ; Debug-Output "INF: Shelling to FindService" Shell $(UtilityInf) FindService, $(KeyProduct) Ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "INF: FindService shell failure" Goto ShellCodeError Endif Ifstr(i) $($R0) != NO_ERROR Debug-Output "INF: FindService Shell error: "$($R0) Goto fatalregistry endif Set KeyParameters = $($R2) ; ; We don't need the services key, so close it. ; CloseRegKey $($R1) Ifstr $(KeyParameters) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find component service" goto fatalregistry endif set OldVersionExisted = $(TRUE) set ValueName = "" set ValueData = "" set ValueStr = "" set ValueList = {} ; ; Get the old values ; EnumRegValue $(KeyParameters) ValueList Debug-Output $(InfName)" KeyParameters is "$(KeyParameters) ifstr(i) $(NT_VER) == NT4 ifint $(PCMCIAStatusFlag) == 8 ForListDo $(ValueList) set ValueItem = $($) set ValueName = *($(ValueItem),1) set ValueData = *($(ValueItem),4) ifstr(i) $(ValueName) == "IoBaseAddress_1" set IOBaseAddrIndex = $(ValueData) else-ifstr(i) $(ValueName) == "IOBaseAddress" set ModemIOBaseAddressIndex = $(ValueData) else-ifstr(i) $(ValueName) == "InterruptNumber" set IRQValueIndex = $(ValueData) else-ifstr(i) $(ValueName) == "PCCARDAttributeMemoryAddress" set MemAddrIndex = $(ValueData) else-ifstr(i) $(ValueName) == "ComPort" set ComPortValueIndex = $(ValueData) ; else-ifstr(i) $(ValueName) == "ComIRQ" ; set ComIrqValueIndex = $(ValueData) endif EndForListDo else ForListDo $(ValueList) set ValueItem = $($) set ValueName = *($(ValueItem),1) set ValueData = *($(ValueItem),4) ifstr(i) $(ValueName) == "IoBaseAddress" set IOBaseAddrIndex = $(ValueData) else-ifstr(i) $(ValueName) == "IOBaseAddress_1" set ModemIOBaseAddressIndex = $(ValueData) else-ifstr(i) $(ValueName) == "InterruptNumber" set IRQValueIndex = $(ValueData) else-ifstr(i) $(ValueName) == "PCCARDAttributeMemoryAddress" set MemAddrIndex = $(ValueData) else-ifstr(i) $(ValueName) == "ComPort" set ComPortValueIndex = $(ValueData) else-ifstr(i) $(ValueName) == "ComIRQ" set ComIrqValueIndex = $(ValueData) endif EndForListDo endif else-ifstr(i) $(NT_VER) == NT3 ForListDo $(ValueList) set ValueItem = $($) set ValueName = *($(ValueItem),1) set ValueData = *($(ValueItem),4) ifstr(i) $(ValueName) == "IoBaseAddress" set IOBaseAddrIndex = $(ValueData) else-ifstr(i) $(ValueName) == "IOBaseAddress_1" set ModemIOBaseAddressIndex = $(ValueData) else-ifstr(i) $(ValueName) == "InterruptNumber" set IRQValueIndex = $(ValueData) else-ifstr(i) $(ValueName) == "PCCARDAttributeMemoryAddress" set MemAddrIndex = $(ValueData) else-ifstr(i) $(ValueName) == "ComPort" set ComPortValueIndex = $(ValueData) else-ifstr(i) $(ValueName) == "ComIRQ" set ComIrqValueIndex = $(ValueData) endif EndForListDo endif Debug-Output $(InfName)" IRQ_Level is "$(IRQValue) Debug-Output $(InfName)" I/o base is "$(IOBaseAddrValue) Debug-Output $(InfName)" Mem base is "$(MemAddrValue) Debug-Output $(InfName)" Com Port Number is "$(ComPortValue) set IRQValue = *($(IRQList), ~($(IRQValues),$(IRQValueIndex))) ifstr(i) $(IRQValue) == "" set IRQValue = *($(IRQList), 3) Debug-Output $(InfName)" IRQ_Level is "$(IRQValue) endif set IOBaseAddrValue = *($(IOBaseAddrList), ~($(IOBaseAddrValues),$(IOBaseAddrIndex))) ifstr(i) $(IOBaseAddrValue) == "" set IOBaseAddrValue = *($(IOBaseAddrList), 1) endif set MemAddrValue = *($(MemAddrList), ~($(MemAddrValues),$(MemAddrIndex))) ifstr(i) $(MemAddrValue) == "" set MemAddrValue = *($(MemAddrList), 1) endif set ComPortValue = *($(ComPortList), ~($(ComPortValues),$(ComPortValueIndex))) ifstr(i) $(ComPortValue) == "" set ComPortValue = *($(ComPortList), 1) endif ;Kenny set ModemIOBaseAddressValue = *($(ModemIOBaseAddressList), ~($(ModemIOBaseAddressValues),$(ModemIOBaseAddressIndex))) ifstr(i) $(ModemIOBaseAddressValue) == "" set ModemIOBaseAddressValue = *($(ModemIOBaseAddressList), $(ComPortValue)) endif set ComIrqValue = *($(ComIrqList), ~($(ComIrqValues),$(ComIrqValueIndex))) ifstr(i) $(ComIrqValue) == "" set ComIrqValue = *($(ComIrqList), 2) endif ; Save the settings as they were read from the Registry. ; Shell $(ParamInf) Param_SaveValues ; Set CurrParamSettings = $($R0) ; ; Put up the adapter configuration dialog if necessary. ; ; Note that $(CurrParamSettings) has the old known parameter values. ; adaptersetup = + ; Shell "" DebugConfiguration "before displaying dialog" Set from = adapteroptions adapteroptions = + ifint $(PCMCIAStatusFlag) == 8 LoadLibrary "Disk 1" $(Dialog$(NT_VER)DllName) hLib else LoadLibrary "Disk 1" $(DialogNT3DllName) hLib endif read-syms FileDependentDlg$(!STF_LANGUAGE) Debug-Output $(InfName)" I/o base is "$(IOBaseAddrValue) ui start "InputDlg" $(hLib) set ExitButton = $(ButtonPressed) Debug-Output " ButtonPressed "$(ButtonPressed) FreeLibrary $(hLib) ifstr(i) $(DLGEVENT) == "CONTINUE" set IOBaseAddrIndex = $(Combo1Out) set IRQValueIndex = $(Combo2Out) set MemAddrIndex = $(Combo3Out) set ComPortValueIndex = $(Combo4Out) ;Kenny set ModemIOBaseAddressIndex = $(ComPortValueIndex) set ComIrqValueIndex = $(Combo5Out) set ExitButton = $(ButtonPressed) ui pop 1 else-ifstr(i) $(DLGEVENT) == "EXIT" set CommonStatus = STATUS_USERCANCEL Debug-Output "Action: exit. Bye." ui pop 1 goto end else ; ; Unknow command ; ui pop 1 Debug-Output "Action: unknown. Bye." goto end endif Debug-Output " Combo list out "$(ComboListItemsOut) ; ; If installing, go create the necessary keys; ; if configuring, they're already open. ; skipoptions =+ ifint $(OldVersionExisted) == $(TRUE) ifstr(i) $(!NTN_InstallMode) == configure goto writeparameters endif endif StartWait ; ; Add Software Component ; ifint $(OldVersionExisted) == $(FALSE) ifstr(i) $(!NTN_InstallMode) == "install" Ifstr(i) $(DoCopy) == "YES" Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1)WINNT\ Endif install "Install-Option" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal endif endif Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), + $(ProductSoftwareName), + $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), + $(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+ $(NetEventDLL) Set OEM_ABANDON_SOFTWARE = TRUE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif ; ; At this point: ; $R1 contains the product version key handle; ; $R2 contains the NetRules subkey handle; ; $R3 contains the new Services key handle; and ; $R4 contains the Parameters key ; $R5 contains the Linkage Key ; set RegistryErrorIndex = $($R0) set KeyProduct = $($R1) Set SoftNetRulesKey = $($R2) CloseRegKey $($R3) CloseRegKey $($R4) CloseRegKey $($R5) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add software components" CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+ {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+ {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+ {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add value list." CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+ {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, + {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, + {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(SoftNetRulesKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Resgitry error: add value list." goto fatalregistry endif endif ; ; Create the HARDWARE\Netcard region and its corresponding service ; Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName) ifint $($R4) != -1 Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4)) endif ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "Cannot add hardware component" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add hardware component" CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) goto fatalregistry endif set KeyParameters = $($R3) set KeyAdapterRules = $($R2) set AdapterNumber = $($R4) set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+ {Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+ {ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $($R1), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif CloseRegKey $($R1) set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)"""" set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm) set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+ {bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Resgitry error: add value list." CloseRegKey $(KeyParameters) CloseRegKey $(KeyAdapterRules) goto fatalregistry endif CloseRegKey $(KeyAdapterRules) goto writeparameters ; ; REQUIRED: $(KeyParameters) contains service Parameters key handle ; writeparameters = + Shell $(UtilityInf), GetBusTypeNum set BusTypeNum = $($R1) ; Testing the BusNum. We are coding it to 0 set BusNumValue = 0 ; ; End of BusNum ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set IRQValue = *($(IRQValues), ~($(IRQList),$(IRQValueIndex))) set IOBaseAddrValue = *($(IOBaseAddrValues), ~($(IOBaseAddrList),$(IOBaseAddrIndex))) ;Kenny set ModemIOBaseAddressValue = *($(ModemIOBaseAddressValues), ~($(ModemIOBaseAddressList), $(ModemIOBaseAddressIndex))) set MemAddrValue = *($(MemAddrValues), ~($(MemAddrList),$(MemAddrIndex))) set ComPortValue = *($(ComPortValues), ~($(ComPortList),$(ComPortValueIndex))) set ComIrqValue = *($(ComIrqValues), ~($(ComIrqList),$(ComIrqValueIndex))) ifstr(i) $(NT_VER) == NT4 ifint $(PCMCIAStatusFlag) == 8 set NewValueList = {{IoBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(ModemIOBaseAddressValue)},+ {IoBaseAddress_1,$(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+ {IoLength, $(NoTitle),$(!REG_VT_DWORD),8},+ {IoLength_1,$(NoTitle),$(!REG_VT_DWORD),32},+ {BusType,$(NoTitle),$(!REG_VT_DWORD),1},+ {BusNumber, $(NoTitle),$(!REG_VT_DWORD),$(BusNumValue)},+ {MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+ {Pcmcia,$(NoTitle),$(!REG_VT_DWORD),1},+ {NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddress)},+ {ModemFunction, $(NoTitle),$(!REG_VT_DWORD),1},+ {InterruptNumber, $(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+ {PCCARDAttributeMemoryAddress, $(NoTitle),$(!REG_VT_DWORD),$(MemAddrValue)},+ {PCCARDAttributeMemoryOffset, $(NoTitle),$(!REG_VT_DWORD),0},+ {PCCARDAttributeMemorySize, $(NoTitle),$(!REG_VT_DWORD),1024},+ {ComPort, $(NoTitle),$(!REG_VT_DWORD),$(ComPortValue)}} else set NewValueList = {{IoBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+ {IoBaseAddress_1,$(NoTitle),$(!REG_VT_DWORD),$(ModemIOBaseAddressValue)},+ {IoLength, $(NoTitle),$(!REG_VT_DWORD),32},+ {IoLength_1,$(NoTitle),$(!REG_VT_DWORD),8},+ {BusType,$(NoTitle),$(!REG_VT_DWORD),1},+ {BusNumber, $(NoTitle),$(!REG_VT_DWORD),$(BusNumValue)},+ {MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+ {Pcmcia,$(NoTitle),$(!REG_VT_DWORD),0},+ {NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddress)},+ {InterruptNumber, $(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+ {PCCARDAttributeMemoryAddress, $(NoTitle),$(!REG_VT_DWORD),$(MemAddrValue)},+ {PCCARDAttributeMemoryOffset, $(NoTitle),$(!REG_VT_DWORD),0},+ {PCCARDAttributeMemorySize, $(NoTitle),$(!REG_VT_DWORD),1024},+ {ComPort, $(NoTitle),$(!REG_VT_DWORD),$(ComPortValue)},+ {ComIRQ, $(NoTitle),$(!REG_VT_DWORD),$(ComIrqValue)}} endif else-ifstr(i) $(NT_VER) == NT3 ifstr(i) $(Option) == ComboCard set NewValueList = {{IoBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+ {IoBaseAddress_1,$(NoTitle),$(!REG_VT_DWORD),$(ModemIOBaseAddressValue)},+ {IoLength, $(NoTitle),$(!REG_VT_DWORD),32},+ {IoLength_1,$(NoTitle),$(!REG_VT_DWORD),8},+ {BusType,$(NoTitle),$(!REG_VT_DWORD),1},+ {BusNumber, $(NoTitle),$(!REG_VT_DWORD),$(BusNumValue)},+ {MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+ {Pcmcia,$(NoTitle),$(!REG_VT_DWORD),1},+ {NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddress)},+ {InterruptNumber, $(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+ {PCCARDAttributeMemoryAddress, $(NoTitle),$(!REG_VT_DWORD),$(MemAddrValue)},+ {PCCARDAttributeMemoryOffset, $(NoTitle),$(!REG_VT_DWORD),0},+ {PCCARDAttributeMemorySize, $(NoTitle),$(!REG_VT_DWORD),1024},+ {ComPort, $(NoTitle),$(!REG_VT_DWORD),$(ComPortValue)},+ {ComIRQ, $(NoTitle),$(!REG_VT_DWORD),$(ComIrqValue)}} else set NewValueList = {{IoBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+ {IoBaseAddress_1,$(NoTitle),$(!REG_VT_DWORD),$(ModemIOBaseAddressValue)},+ {IoLength, $(NoTitle),$(!REG_VT_DWORD),32},+ {IoLength_1,$(NoTitle),$(!REG_VT_DWORD),8},+ {BusType,$(NoTitle),$(!REG_VT_DWORD),1},+ {BusNumber, $(NoTitle),$(!REG_VT_DWORD),$(BusNumValue)},+ {MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+ {Pcmcia,$(NoTitle),$(!REG_VT_DWORD),0},+ {NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddress)},+ {InterruptNumber, $(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+ {PCCARDAttributeMemoryAddress, $(NoTitle),$(!REG_VT_DWORD),$(MemAddrValue)},+ {PCCARDAttributeMemoryOffset, $(NoTitle),$(!REG_VT_DWORD),0},+ {PCCARDAttributeMemorySize, $(NoTitle),$(!REG_VT_DWORD),1024},+ {ComPort, $(NoTitle),$(!REG_VT_DWORD),$(ComPortValue)},+ {ComIRQ, $(NoTitle),$(!REG_VT_DWORD),$(ComIrqValue)}} endif endif Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList) CloseRegKey $(KeyParameters) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output "Registry error: Add value list" goto fatalregistry endif ;;;;; andge OpenRegKey $(!REG_H_LOCAL) "" $(CardwizDataBase) $(MAXIMUM_ALLOWED) KeyCardwiz ifstr $(KeyCardwiz) == $(KeyNull) Debug-Output "D65: Registry Open Fail -- CardwizDataBase" goto CardWizEnd endif Debug-Output "D65: Open CardwizDataBase Registry Successful" OpenRegKey $(!REG_H_LOCAL) "" $(CWZNICDataBase) $(MAXIMUM_ALLOWED) KeyDataBase2 ifstr $(KeyDataBase2) == $(KeyNull) CreateRegKey $(KeyCardwiz) {"PCMCIAs\ComboCard",$(NoTitle),GenericClass} "" $(MAXIMUM_ALLOWED) "" KeyDataBase2 ifstr $(KeyDataBase2) == $(KeyNull) goto CardWizEnd endif endif Debug-Output "D65: Cardwiz Set Keyword value -- Driver" SetRegValue $(KeyDataBase2) {"MacDriverHandle",$(NoTitle),$(!REG_VT_DWORD),0} SetRegValue $(KeyDataBase2) {"MacDriverName",$(NoTitle),$(!REG_VT_SZ),"LMNDISA"} SetRegValue $(KeyDataBase2) {"MacDriverState",$(NoTitle),$(!REG_VT_DWORD),1} SetRegValue $(KeyDataBase2) {"MacDriverVersion",$(NoTitle),$(!REG_VT_DWORD),0x300} SetRegValue $(KeyDataBase2) {"MacSwapCapability",$(NoTitle),$(!REG_VT_DWORD),2} CloseRegKey $(KeyDataBase2) ;+ Kenny 10/20'98 OpenRegKey $(!REG_H_LOCAL) "" $(CWZNICDataBase2) $(MAXIMUM_ALLOWED) KeyDataBase2 ifstr $(KeyDataBase2) == $(KeyNull) CreateRegKey $(KeyCardwiz) {"PCMCIAs\LanModem",$(NoTitle),GenericClass} "" $(MAXIMUM_ALLOWED) "" KeyDataBase2 ifstr $(KeyDataBase2) == $(KeyNull) goto CardWizEnd endif endif Debug-Output "D65: Cardwiz Set Keyword value -- Driver" SetRegValue $(KeyDataBase2) {"MacDriverHandle",$(NoTitle),$(!REG_VT_DWORD),0} SetRegValue $(KeyDataBase2) {"MacDriverName",$(NoTitle),$(!REG_VT_SZ),"LMNDISA"} SetRegValue $(KeyDataBase2) {"MacDriverState",$(NoTitle),$(!REG_VT_DWORD),1} SetRegValue $(KeyDataBase2) {"MacDriverVersion",$(NoTitle),$(!REG_VT_DWORD),0x300} SetRegValue $(KeyDataBase2) {"MacSwapCapability",$(NoTitle),$(!REG_VT_DWORD),2} CloseRegKey $(KeyDataBase2) ;- Kenny 10/20'98 CloseRegKey $(KeyCardwiz) CardWizEnd = + OpenRegKey $(!REG_H_LOCAL) "" $(PCCardDataBase) $(MAXIMUM_ALLOWED) KeyPCCard ifstr $(KeyPCCard) == $(KeyNull) Debug-Output "D65: Registry Open Fail -- PCCardDataBase" ;Kenny goto fatalregistry goto NT350 endif Debug-Output "D65: Open PCCardDataBase Registry Successful" OpenRegKey $(!REG_H_LOCAL) "" $(NICDataBase) $(MAXIMUM_ALLOWED) KeyDataBase ifstr $(KeyDataBase) == $(KeyNull) Debug-Output "D65: Keyword PCMCIAs\ComboCard does not exist" CreateRegKey $(KeyPCCard) {"PCMCIAs\ComboCard",$(NoTitle),GenericClass} "" $(MAXIMUM_ALLOWED) "" KeyDataBase ifstr $(KeyDataBase) == $(KeyNull) Debug-Output "D65: PCMCIAs\ComboCard Can not Create" CloseRegKey $(KeyPCCard) goto fatalregistry endif Debug-Output "D65: Create PCMCIAs\ComboCard Successful" endif Debug-Output "D65: Set Keyword value -- Driver" SetRegValue $(KeyDataBase) {"AttributeMemorySize",$(NoTitle),$(!REG_VT_DWORD),4096} SetRegValue $(KeyDataBase) {"Driver",$(NoTitle),$(!REG_VT_SZ),"ComboCard"} SetRegValue $(KeyDataBase) {"DeviceType",$(NoTitle),$(!REG_VT_SZ),"NET"} CloseRegKey $(KeyDataBase) ;+ Kenny 10/20'98 OpenRegKey $(!REG_H_LOCAL) "" $(NICDataBase2) $(MAXIMUM_ALLOWED) KeyDataBase ifstr $(KeyDataBase) == $(KeyNull) Debug-Output "D65: Keyword PCMCIAs\LanModem does not exist" CreateRegKey $(KeyPCCard) {"PCMCIAs\LanModem",$(NoTitle),GenericClass} "" $(MAXIMUM_ALLOWED) "" KeyDataBase ifstr $(KeyDataBase) == $(KeyNull) Debug-Output "D65: PCMCIAs\LanModem Can not Create" CloseRegKey $(KeyPCCard) goto fatalregistry endif Debug-Output "D65: Create PCMCIAs\LanModem Successful" endif Debug-Output "D65: Set Keyword value -- Driver" SetRegValue $(KeyDataBase) {"AttributeMemorySize",$(NoTitle),$(!REG_VT_DWORD),4096} SetRegValue $(KeyDataBase) {"Driver",$(NoTitle),$(!REG_VT_SZ),"ComboCard"} SetRegValue $(KeyDataBase) {"DeviceType",$(NoTitle),$(!REG_VT_SZ),"NET"} CloseRegKey $(KeyDataBase) ;- Kenny 10/20'98 CloseRegKey $(KeyPCCard) ifstr(i) $(NT_VER) == NT3 OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters\SerialCombo" $(MAXIMUM_ALLOWED) NewSerialHandle Ifstr $(NewSerialHandle) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialKey CreateRegKey $(SerialKey) {"SerialCombo",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" NewSerialHandle CloseRegKey $(SerialKey) endif set NewValueList = {{DosDevices, $(NoTitle),$(!REG_VT_SZ), "COM"$(ComPortValue)},+ ; "COMx" {ForceFifoEnable, $(NoTitle),$(!REG_VT_DWORD), 0},+ {Interrupt, $(NoTitle),$(!REG_VT_DWORD), $(ComIrqValue)},+ {PortAddress, $(NoTitle),$(!REG_VT_DWORD), $(ModemIOBaseAddressValue)}} Shell $(UtilityInf), AddValueList, $(NewSerialHandle), $(NewValueList) CloseRegKey $(NewSerialHandle) ; add comm port info to HARDWARE\DEVICEMAP\SERIALCOMM section OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP\SERIALCOMM" $(MAXIMUM_ALLOWED) NewSerialHandle Ifstr $(NewSerialHandle) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP" $(MAXIMUM_ALLOWED) SerialKey CreateRegKey $(SerialKey) {"SERIALCOMM",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" NewSerialHandle CloseRegKey $(SerialKey) endif SetRegValue $(NewSerialHandle) {"SerialCombo",$(NoTitle),$(!REG_VT_SZ),"COM"$(ComPortValue)} CloseRegKey $(NewSerialHandle) ; add comm port info to SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports section OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports" $(MAXIMUM_ALLOWED) NewSerialHandle Ifstr $(MyNewSerialHandle) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(MAXIMUM_ALLOWED) SerialKey CreateRegKey $(SerialKey) {"Ports",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" NewSerialHandle CloseRegKey $(SerialKey) endif SetRegValue $(MyNewSerialHandle) {"COM"$(ComPortValue)":",$(NoTitle),$(!REG_VT_SZ), "9600,n,8,1"} CloseRegKey $(MyNewSerialHandle) else-ifint $(PCMCIAStatusFlag) != 8 OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters\SerialCombo" $(MAXIMUM_ALLOWED) NewSerialHandle Ifstr $(NewSerialHandle) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialKey CreateRegKey $(SerialKey) {"SerialCombo",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" NewSerialHandle CloseRegKey $(SerialKey) endif set NewValueList = {{DosDevices, $(NoTitle),$(!REG_VT_SZ), "COM"$(ComPortValue)},+ ; "COMx" {ForceFifoEnable, $(NoTitle),$(!REG_VT_DWORD), 0},+ {Interrupt, $(NoTitle),$(!REG_VT_DWORD), $(ComIrqValue)},+ {PortAddress, $(NoTitle),$(!REG_VT_DWORD), $(ModemIOBaseAddressValue)}} Shell $(UtilityInf), AddValueList, $(NewSerialHandle), $(NewValueList) CloseRegKey $(NewSerialHandle) ; add comm port info to HARDWARE\DEVICEMAP\SERIALCOMM section OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP\SERIALCOMM" $(MAXIMUM_ALLOWED) NewSerialHandle Ifstr $(NewSerialHandle) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP" $(MAXIMUM_ALLOWED) SerialKey CreateRegKey $(SerialKey) {"SERIALCOMM",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" NewSerialHandle CloseRegKey $(SerialKey) endif SetRegValue $(NewSerialHandle) {"SerialCombo",$(NoTitle),$(!REG_VT_SZ),"COM"$(ComPortValue)} CloseRegKey $(NewSerialHandle) ; add comm port info to SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports section OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports" $(MAXIMUM_ALLOWED) NewSerialHandle Ifstr $(MyNewSerialHandle) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(MAXIMUM_ALLOWED) SerialKey CreateRegKey $(SerialKey) {"Ports",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" NewSerialHandle CloseRegKey $(SerialKey) endif SetRegValue $(MyNewSerialHandle) {"COM"$(ComPortValue)":",$(NoTitle),$(!REG_VT_SZ), "9600,n,8,1"} CloseRegKey $(MyNewSerialHandle) endif NT350 = + ;;;;; end of andge EndWait goto successful ;----------------------------------------------- ; Binding section ;----------------------------------------------- bindingadapter =+ set Error = "Binding: Sorry, not yet implemented." goto fatal ;----------------------------------------------- ; Removeadapter section ;----------------------------------------------- removeadapter = + Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) ; Remove Software Component Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif else Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $(!NTN_RegBase) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif ifstr(i) $(NT_VER) == NT3 OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialHandle DeleteRegTree $(SerialHandle) SerialCombo CloseRegKey $(SerialHandle) else-ifint $(PCMCIAStatusFlag) != 8 OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialHandle DeleteRegTree $(SerialHandle) SerialCombo CloseRegKey $(SerialHandle) endif endif goto end ;----------------------------------------------- ; Upgrade Software section ;----------------------------------------------- UpgradeSoftware = + ; ; First determine whether we want to do upgrade or update for software ; or hardware component. Then we will determine whether the Mode is ; update or upgrade. ; ; If the same version of the product existed in the registry, we do ; update. Otherwise, we will do a upgrade ; ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) ; Upgrade software component ; ; see whether the same version exist or not ; OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) GetRegValue $(KeyProduct),"MajorVersion", VersionInfo set Version = *($(VersionInfo), 4) ; ; Update the binaries ; Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set !UG_Filename = $($R0) ifstr(i) $(!UG_Filename) != "" install "Install-Update" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS goto fatal endif endif ; Upgrade the version number ; SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)} SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)} ; ; do nothing for update ; ifint $(Version) != $(ProductVersion) ; ; If the major version number is not the same, ; it is major upgrade. So let Upgrade the product ; ; ; make other upgrade change if necessary ; endif CloseRegKey $(KeyProduct) else ; ; Cannot Open software key, goto ERROR ; goto fatalregistry endif else ; ; upgrade/update hardware component ; There is no different between upgrade and update for hardware ; component ; ; 1. Get the Service Name ; 2. Change the NetRule section if necessary ; OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) + $(MAXIMUM_ALLOWED) NetworkCardKey Ifstr(i) $(NetworkCardKey) != $(KeyNull) ; ; Get Service name ; GetRegValue $(NetworkCardKey),"ServiceName", ServiceNameInfo set ServiceName = *($(ServiceNameInfo), 4) ; ; Change the NetRule if necessary ; OpenRegKey $(NetworkCardKey) "" "NetRules" + $(MAXIMUM_ALLOWED) NetRuleKey Ifstr(i) $(NetRuleKey) != $(KeyNull) ; ; Make the change.... ; else ; ; Error, cannot open net rules key ; goto fatalregistry endif CloseRegKey $(NetRules) CloseRegKey $(NetworkCardKey) else ; ; Error, cannot open network card key ; goto fatalregistry endif ; ; 3. Change the service section of the hardware. i.e., ; ParameterName change, value change, etc. ; OpenRegKey $(!REG_H_LOCAL) "" + $(!NTN_ServiceBase)"\"$(ServiceName) + $(MAXIMUM_ALLOWED) ServiceKey Ifstr(i) $(ServiceKey) != $(KeyNull) ; ; Get the ServiceKey to change the Start value ; or Type value. Or open Parameters key to ; change the hardware parameters if necessary. ; CloseRegKey $(ServiceKey) else ; ; Error, cannot open network card key ; goto fatalregistry endif endif goto end ; ; End of Upgrade Software ; ; ; Escape hatches ; successful = + goto end abandon = + ForListDo $(OEM_ABANDON_OPTIONS) Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $($) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif EndForListDo Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE ; Remove Software Component Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), FALSE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end ; ; warning display ; warning = + Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(to) else-ifstr(i) $($R1) == "CANCEL" goto $(from) else goto "end" endif ; ; non fatal error display ; nonfatalinfo = + Set Severity = STATUS Set CommonStatus = STATUS_USERCANCEL goto nonfatalmsg nonfatal = + Set Severity = NONFATAL goto nonfatalmsg nonfatalmsg = + ifstr(i) $(Error) == "" Set Severity = NONFATAL Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(from) else goto "end" endif ; ; Registry is broken ; fatalregistry = + Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal ; ; Netcard detection failure ; fataldetect = + Shell $(UtilityInf),RegistryErrorString,CANNOT_DETECT ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif set Error = $($R0) Goto fatal ; ; fatal error display ; fatal = + ifstr(i) $(Error) == "" Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif goto setfailed ; ; Shelling error ; ShellCodeError = + set DlgType = "MessageBox" set STF_MB_TITLE = $(ShellCodeErrorTitle) set STF_MB_TEXT = $(ShellCodeErrorText) set STF_MB_TYPE = 1 set STF_MB_ICON = 3 set STF_MB_DEF = 1 ui start "Error Message" goto setfailed setfailed = + set CommonStatus = STATUS_FAILED ; ; if OEM_ABANDON_ON == TRUE, then remove the registry entries ; ifstr(i) $(OEM_ABANDON_ON) == TRUE set OEM_ABANDON_ON = FALSE goto abandon endif goto end end = + goto term term = + Return $(CommonStatus) [DebugConfiguration] Set InfName = "inf" Debug-Output $(InfName)" **CONFIGURATION STATE: "$($0) Debug-Output $(InfName)" IRQ_Level is "$(!p:IRQValue) Debug-Output $(InfName)" IOBaseAddrValue is "$(!p:IOBaseAddrValue) Debug-Output $(InfName)" MemAddrValue is "$(!p:MemAddrValue) Debug-Output $(InfName)" ComPortNumber is "$(!p:ComPortValue) Debug-Output $(InfName)" TransceiverValue is "$(!p:TransceiverValue) Debug-Output $(InfName)" MemBaseAddrDec is "$(!p:MemBaseAddrDec) Debug-Output $(InfName)" MappedValue is "$(!p:MappedValue) return ;*************************************************************** ; INSTALL SECTIONS ;*************************************************************** [Install-Option] set STF_VITAL = "" ifstr(i) $(AddCopy) == "YES" ; ; Add the files to the copy list ; ; BUGBUG: eliminate the "nt2" in the next line when Sunil fixes ; the other INF files ; ifint $(PCMCIAStatusFlag) == 8 AddSectionFilesToCopyList Files-$(NT_VER) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers else AddSectionFilesToCopyList Files-NT3 $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers endif endif ifstr(i) $(DoCopy) == "YES" ; ; Copy files in the copy list ; set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList endif Exit [Install-Update] set STF_VITAL = "" set STF_OVERWRITE = "VERIFYSOURCEOLDER" ;set STF_VERSION = "YES" ifint $(PCMCIAStatusFlag) == 8 AddSectionFilesToCopyList Files-$(NT_VER) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers else AddSectionFilesToCopyList Files-NT3 $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers endif AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH) set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList exit [Install-Dll] set STF_VITAL = "" ifint $(PCMCIAStatusFlag) == 8 AddSectionFilesToCopyList Files-$(NT_VER)-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH) else AddSectionFilesToCopyList Files-NT3-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH) endif set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList exit [Source Media Descriptions] 1 = "PLANET ENW-3503 LanModem Driver Disk" , TAGFILE = disk1 [ProductType] STF_PRODUCT = Winnt STF_PLATFORM = I386 [Files-Inf] 1, oemsetnt.inf, SIZE=2000, RENAME=$(!UG_Filename) [Files-NT3] 1, LMNDIS.SYS , SIZE=88888 1, MODEM.INF, SIZE=250000, BACKUP=MODEM.BAK, DESTINATION=$(!STF_WINDOWSSYSPATH)\RAS DECOMPRESS RENAME=MODEM.INF 1, MDMLMX.INF, SIZE=60000, DESTINATION=$(!STF_WINDOWSSYSPATH)\..\INF [Files-NT4] 1, LMNDISA.SYS , SIZE=88888 1, MDMLMX.INF, SIZE=60000, DESTINATION=$(!STF_WINDOWSSYSPATH)\..\INF [Files-NT3-Dll] 1, LMNDIS.dll, SIZE=3000 [Files-NT4-Dll] 1, LMNDISA.dll, SIZE=3000 [LanguagesSupported] ENG [OptionsTextENGNT4] ComboCard = ""PLANET ENW-3503 Ethernet Fax/Modem Card" [OptionsTextENGNT3] ComboCard = "PLANET ENW-3503 Ethernet Fax/Modem Card on PCIC compatible controller" ComboCardA = "PLANET ENW-3503 Ethernet Fax/Modem Card on CL-PD6729 or CardBus controller" [FileConstantsENG] ProCaption = "Windows NT Setup" ProCancel = "Cancel" ProCancelMsg = "Windows NT Networking is not correctly installed. "+ "Are you sure you want to cancel copying files?" ProCancelCap = "Network Setup Message" ProText1 = "Copying:" ProText2 = "To:" FunctionTitle = $(GenericFunctionName)" Setup" ProductSoftwareDescription = $(GenericDriverName) ProductHardwareDescription = $(GenericAdapterName) ProductHardwareComboCardDescription="PLANET ENW-3503 Ethernet Fax/Modem Card" ProductHardwareComboCardADescription="PLANET ENW-3503 Ethernet Fax/Modem Card" ProductSoftwareTitle = $(GenericDriverName) ProductHardwareComboCardTitle = $(GenericAdapterName) ProductHardwareComboCardATitle = $(GenericAdapterName) DialogNT3DllName = "LMNDIS.dll" DialogNT4DllName = "LMNDISA.dll" IRQList = ^(IRQChoices, 1) IRQValues = ^(IRQChoices, 2) IOBaseAddrList = ^(IOBaseAddrChoices, 1) IOBaseAddrValues = ^(IOBaseAddrChoices, 2) ModemIOBaseAddressList = ^(ModemIOBaseAddressChoices,1) ModemIOBaseAddressValues = ^(ModemIOBaseAddressChoices,2) MemAddrList = ^(MemAddrChoices, 1) MemAddrValues = ^(MemAddrChoices, 2) ComPortList = ^(ComPortChoices, 1) ComPortValues = ^(ComPortChoices, 2) ComIrqList = ^(ComIrqChoices, 1) ComIrqValues = ^(ComIrqChoices, 2) [DialogConstantsENG] Help = "&Help" Exit = "Cancel" OK = "OK" HelpContext = "" Continue = "Continue" Cancel = "Cancel" [MemoryMappedChoicesENG] Map_1 = 1, "ON" Map_2 = 0, "OFF" [FileDependentDlgENG] DlgText = "Please select values for the follwing fields:" DlgType = "RadioCombination" DlgTemplate = "Kenny" Caption = $(FunctionTitle) CBOptionsGreyed = {} NotifyFields = {NO, NO} Combo1Label = "I/O &Base:" Combo2Label = "&Interrupt:" Combo3Label = "&Memory:" Combo4Label = "&COM Port:" Combo5Label = "COM I&RQ:" Combo1List = $(IOBaseAddrList) Combo1Out = $(IOBaseAddrValue) Combo2List = $(IRQList) Combo2Out = $(IRQValue) Combo3List = $(MemAddrList) Combo3Out = $(MemAddrValue) Combo4List = $(ComPortList) Combo4Out = $(ComPortValue) Combo5List = $(ComIrqList) Combo5Out = $(ComIrqValue) ComboListItemsIn = {Combo1List,Combo2List,Combo3List,Combo4List,Combo5List} ComboListItemsOut = {Combo1Out,Combo2Out,Combo3Out,Combo4Out,Combo5Out} EditTextIn = "" EditTextLim = "" [IRQChoices] IRQ_1 = "3",3 IRQ_2 = "4",4 IRQ_3 = "5",5 IRQ_4 = "7",7 IRQ_5 = "9",9 IRQ_6 = "10",10 IRQ_7 = "11",11 IRQ_8 = "12",12 IRQ_9 = "15",15 [IOBaseAddrChoices] IOBase_1 = "0x300",768 IOBase_2 = "0x320",800 IOBase_3 = "0x340",832 IOBase_4 = "0x360",864 [ModemIOBaseAddressChoices] MdmIOBase_1 = "1",1016 MdmIOBase_2 = "2",760 MdmIOBase_3 = "3",1000 MdmIOBase_4 = "4",744 [MemAddrChoices] Memory_1 = "0xD0000",851968 Memory_2 = "0xD4000",868352 Memory_3 = "0xD8000",884736 Memory_4 = "0xDC000",901120 [ComPortChoices] ComPort_1 = "2",2 ComPort_2 = "3",3 ComPort_3 = "4",4 [ComIrqChoices] ComIrq_1 = "2",2 ComIrq_2 = "3",3 ComIrq_3 = "4",4 ComIrq_4 = "5",5 ComIrq_5 = "6",6 ComIrq_6 = "7",7 ComIrq_7 = "8",8 ComIrq_8 = "9",9 ComIrq_9 = "10",10 ComIrq_10= "11",11 ComIrq_11= "12",12 ComIrq_12= "13",13 ComIrq_13= "14",14 ComIrq_14= "15",15Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.