AcerLAN ALN-315 10/100 Base-TX Fast Ethernet Adapter
NDIS 4 DRIVER FOR WINDOWS 98 INSTALLATION
==========================================================
Contents:
---------
A) Install NDIS 4.0 driver to the Windows 98
B) Configuration NDIS 4 driver to the Windows 98
C) Configuration NDIS 2.01 driver to the Windows 98
A) Install NDIS 4 driver to the Windows 98
The drivers named ALN315.SYS contained in the directory
WIN98.
NDIS Driver Installation on Windows 98
--------------------------------------
1. Plug AcerLAN ALN-315 10/100 Base-TX Fast Ethernet Adapter
into one of the Master PCI slots of your PCI platform.
2. Turn power on then boot from Windows 98.
3. When Win98 finds the ALN-315 adapter,it will show a dialog box of
"Update Device Driver Wizard".The message of "The wizard will complete
the installation: PCI Ethernet Controller" will be shown,then
select "Next".
4. There will show a message of
"Windows was unable to locate a driver for this device."
Insert the AcerLAN ALN-315 driver disk into drive A and select
"Other Locations".
5. Specify the driver pathname "A:\WIN98" in the dialog box of
Select "Other Location".
6. There will show a message of "Windows found the following updated
driver for this device: AcerLAN ALN-315 10/100 Base-TX Ethernet
Adapter." and "Location of Driver : WIN98" in the dialog box of
"Update Device Driver Wizard".Select "Finish".
7. Windows 98 will appear a message for you to specify the path of
the source drivers and insert Windows 98 system disk to complete
setup steps.
8. Windows 98 will finish the other installation procedure
automatically, then you restart the system.
9. Restart Windows 98 after you have installed the driver.
B) Configuration NDIS 4.0 driver to the Windows 98
1. Click the "My Computer" icon in the Main Program Group.
2. Click the "Control Panel" icon from My Computer window.
3. Click the "Network" icon from the Control Panel window.
4. Select "Adapter" item from Network Component Type dialog box,
then click "Properties..." button.
5. Click "Advanced" button from Properties for
AcerLAN ALN-315 10/100 Base-TX Fast Ethernet Adapter dialog box.
6. Here, you can set the following properties:
<1>. 100Mbps Transmit Threshold :
128 bytes ;Default is 128 bytes
256 bytes
512 bytes
1024 bytes
<2>. 10Mbps Transmit Threshold :
72 bytes ;Default is 96 bytes
96 bytes
128 bytes
160 bytes
<3>. Burst Length : 1 Dword ; Default is 16 Dwords.
2 Dwords ; (1 Dword = 4 bytes).
4 Dwords
8 Dwords
16 Dwords
32 Dwords
<4>. Connection Type :
100Base-TX ; Default is AutoSense
100Base-TX Full_Duplex
10BaseT (Twisted Pair)
10BaseT Full_Duplex
AutoSense
<5>. Extra Receive Buffers :
0 ;Default is 16
16
32
64
128
<6>. Extra Receive Packets :
16 ;Default is 100
32
64
100
200
<7>. Interrupt Mitigation : Disabled , Enabled ;Default is Disabled
<8>. Memory Read Multiple : Disabled , Enabled ;Default is Disabled
<9>. No Cable Indication : Disabled , Enabled ;Default is Disabled
<10>. Receive Buffers : 8, 16, 32, 48, 64.
default is 16.
<11>. Snooze Mode : Disabled , Enabled. ;Default is Disabled.
<12>. Store and Forward : Disabled , Enabled. ;Default is Disabled.
<13>. Underrun Max Retries :
2 ;Default is 10
4
6
8
<14>. Underrun Threshold :
10 ;Default is 10
20
50
100
7. Follow screen instructions to complete the process.
8. Restart your computer.
C) Configuration NDIS 2.01 driver to the Windows 98
As described in step <1> to <5> in C) procedure
You can see three properties are followed by "(RealMode NDIS)" i.e.
Data Rate,SIA Mode and Slot Number.
These properties are specific for NDIS 2 driver.
<1> Data Rate: for AcerLAN ALN-315 10/100 Base-TX Fast Ethernet Adapter.
MB10 : speed is 10 Mbps,
MB100: speed is 100 Mbps.
<2> SIA Mode: the connection type of the LAN board,
can be selected from Twisted Pair, TP FULL DUPLEX
and AutoSense, default is AutoSense.
<3> Slot number: the PCI board index, range is 16..26, default is 16.
This parameter is used to distinguish activated board
when multiple 32-bit PCI LAN boards are enabled by the
driver.For two or more ALN-315 cards, this parameters is
required and cannot be omitted from PROTOCOL.INI.
The slot number. for the first LAN card is 16, for the
second is 17, and 18 for the third, etc.
Default value is 16.
===End of File===
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.