440xudiag.txt Driver File Contents (R149798.EXE)


User can have the following options.
 1.  -l <file> 	:Log data to file. 
 2.  -c <num>	:Specify the card to be tested. 
 3.  -I <num>	:Iteration number
 4.  -t <id>	:Disable tests
 5.  -T <id>	:Enable tests
 6.  -r <num>   : Input radix
 7.  -lbm       : Option to specify number of packets in Mac Loopback test
 8.  -lbp       : Option to specify number of packets in Phy Loopback test
 9.  -lbh       : Option to specify number of packets in 100BT External Loopback test
10.  -lbt       : Option to specify number of packets in 10BT External Loopback test
11.  -info      : Option to display Dev ID Ven ID SVen ID SSystem ID
12.  -elog	: Produces a log file with only error information
13.  -x         : Force to search device by using Vendor ID

Example:

> b44udiag -l test.log -c 1 -I 2 -t A3 -lbm 3000 -lbp 3000 -lbh 3000 -lbt 3000

> b44udiag -x
  When the Device ID gets changed to something unrecognized, -x option switch allow 
  b44diag to search device by vendor ID.  
 

There are 3 groups of test. Each group has a few sub tests.
Group A
A1. Indirect Control Register Test
A2. Direct Control Register Test
A3. Interrupt test
A4. Built In Self Test
A5. CAM Read/Write Test

Group B
B1. LEDs test
B2. EEPROM Test
B3. MII Test
B4. Link Status Test

Group C
C1. MAC Loopback Test
C2. PHY Loopback Test.
C3. External Loopback Test 100BT.
C4. External Loopback Test 10BT.
C5. PHY Loopback Test w/ CAM Enabled.
C6. External Loopback Test 100BT w/ CAM Enabled.  
C7. External Loopback Test 10BT w/ CAM Enabled.
C8  MIB MAC Loopback Test

Test Descriptions
A1.  
Indirect Register Test
Command: regtest -i
Function: Each Register specified in the configuration contents read only bit and
read/write bit defines. The test writing zero and one by using indirect addressing method into the test bits to insure the read
only bits are not changed, and read/write bits are changed accordingly.
Default: Enabled

A2
Control Register Test
Command: regtest
Function: Each Register specified in the configuration contents read only bit and
read/write bit defines. The test writing zero and one into the test bits to insure the read
only bits are not changed, and read/write bits are changed accordingly.
Default: Enabled

A3	
Interrupt Test
Command: intrtest
Function: This test verifies the interrupt functionality. It enables interrupt and waits for
interrupt to occur. It waits for 500ms and reports error if could not generate interrupts.
Default: Enabled

A4
Built In Self Test
Command: bist
Function: This test will run the Built In Self Test
Default: Enabled

A5
CAM Read/Write Test
Command: camtest
Function: This test will run the CAM Read/Write Test.  48 Bit patterns will be written to 64 entries of the CAM space.
Test will read back the 64 entries and check.  It will be tested against 5 patterns such as FFFF, 0000, 5555, AAAA, 55AA, AA55.
Default: Enabled

B1
LED Test
Command: ledtest
Function: Tests forcing of the link state for each link speed/duplex.
Default: Enabled

B2
EEPROM Test
Command: setest
Function: Reads Serial Prom and varifies integrity by checking CRC.	
Default: Enabled

B3
MII Test
Command: miitest
Function: Each Register specified in the configuration contents read only bit and
read/write bit defines. The test writing zero and one into the test bits to insure the
read only bits value are not changed, and read/write bits are changed
accordingly.
Default: Enabled

B4
Command: linkstatus
Function: Report current link status.
Default: Enabled

C1
Mac Loopback Test
Command: lbtest -m
Function: Transmits a 2000 or specified by -lbm option of 1514-byte packets with incrementing data pattern, and
checks tx and rx flags and data integrity. 
Default: Enabled

C2
Phy Loopback Test
Command: lbtest -p
Function: This test is same as C1. Mac Loopback Test except, the data is routed
back via physical layer device. 
Default: Enabled

C3 
External Loopback Test 100BT
Command: lbtest -e
Function: This test is same as C1. Mac Loopback Test except, the data is routed
back via loopback device.  
Default: Disabled

C4 
External Loopback Test 10BT
Command: lbtest -a
Function: This test is same as C1. Mac Loopback Test except, the data is routed
back via loopback device.  
Default: Disabled

C5
Phy Loopback Test with CAM Enabled
Command: camlbtest -p
Function: This test is same as C2. Phy Loopback Test except, the data is routed
back via physical layer device with CAM matching enabled.
Default: Enabled

C6 
External Loopback Test 100BT with CAM Enabled
Command: camlbtest -e
Function: This test is same as C5. Phy Loopback Test except, the data is routed
back via loopback device with CAM matching enabled.  
Default: Disabled

C7 
External Loopback Test 10BT with CAM Enabled
Command: camlbtest -a
Function: This test is same as C5. Phy Loopback Test except, the data is routed
back via loopback device with CAM matching enabled.  
Default: Disabled

C8
MIB MAC Loopback Test
Command: mibtest
Function: Test each bit of the MIB counters.  By mac looping back a back to test
          if MIB counter bit will get incremented.
Default: Enabled

By default, all tests except C3, C4, C6 and C7 will be covered in manufacture mode unless disabled by user.

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: ftp, load: 1.32