1. IEE_10.ZIP Driver
2. NWPERS.TXT File Contents

NWPERS.TXT Driver File Contents (IEE_10.ZIP)

   Personal NetWare
                                                                    v3.03


Personal NetWare* Installation Notes for Intel's EtherExpress(TM) PRO/10
ISA LAN Adapter
========================================================================

Location of Driver:     \DOS\EPROODI.COM


General Installation
--------------------

The installation procedure will transfer files to a specific directory on
the workstation and create or modify existing configuration files to fit
your specific needs.  The installation utility INSTALL.EXE is located on
Personal NetWare's Installation + Utilities 1 disk.


Installation Procedure
----------------------

1  Run INSTALL.EXE from the Installation + Utilities 1 Disk.

2  The Personal NetWare Install program screen will appear.  You must
   complete each of the questions.  These options are specific to your
   needs.
   
   a  Step #1 asks for your name, company name, and serial number of your
      copy of Personal NetWare.
   
   b  Step #2 gives you the option to load support files for MS Windows*
      and tells you the disk space requirements. You will also have an
      option to change the directory where the Personal NetWare files
      will be copied. The default directory is C:\NWCLIENT.  You can
      specify another directory if you desire.
   
   c  Step #3 asks you to select a Primary Network Interface Card. From
      the list of drivers select "OEM Supplied Driver".
      
            NOTE:  Do not select Intel EtherExpress(TM) ISA family. This
            driver is for the EtherExpress 16 adapter, not for the
            EtherExpress PRO/10 ISA adapter.
   
   d  Step #4 will ask you to insert the diskette containing the driver
      files. Insert the EtherExpress PRO/10 ISA adapter diskette into
      drive A: and specify the source path for driver files as A:\DOS.
   
   e  Step #5 will let you specify if you want to Share This Computer's
      Resources.
   
   f  Step #6 will let you specify a User Name for this computer.
   
   g  Step #7 will let you specify which Novell NetWare Servers are
      available on your network.
   
   h  Step #8 will allow you to configure Optimization / Network
      Management. Refer to your Personal NetWare Manual to decide which
      options you need.
   
   i  Step #9 is Configure Primary Interface Card. Specify the PORT
      address that was configured in SoftSet2 for the EtherExpress PRO/10
      ISA adapter. The default port address is 300. Select the Ethernet
      frame type you want to use. The default frame is Ethernet_802.2.
   
   j  Step #10 is to accept all the configuration parameters. If
      everything is configured correctly, accept the configuration and
      start the installation. The Personal NetWare installation will now
      prompt you for the installation diskettes as needed.
   
   k  Step #11 is the final step. You will be prompted to insert the
      driver diskette for the third party software driver. Insert the
      EtherExpress PRO/10 ISA adapter diskette into drive A: and specify
      the path to copy the files from as A:\DOS.

Hints and Tips
--------------

1  NET.CFG Options:

   PORT - This is the base I/O address of the adapter.  Verify setting in
   SoftSet2.

   INT - (optional)The system IRQ for the adapter to use.  This option is
   only used as a reminder for which IRQ the board is set for.  It does
   not cause the driver to override the EEPROM contents.

   NODE ADDRESS - This parameter allows the driver to override the
   Ethernet address in the EEPROM. This is Novell's node address override
   feature. To comply with Novell's multicast specification, the second
   digit of the overriding address should be a 2, 6, A or E.
        Syntax:
      NODE ADDRESS 00A0C9123456

2  Be sure to add LASTDRIVE=Z to your CONFIG.SYS file for the network
   mappings to work properly.

3  Below is a sample NET.CFG and STARTNET.BAT. These files are located in
   the C:\NWCLIENT directory by default.
         
         STARTNET.BAT:
   
   @ECHO OFF
   SET NWLANGUAGE=ENGLISH
   C:
   CD C:\NWCLIENT
   LH SHARE /F:10240 /L:200
   LH LSL
   LH EPROODI
   LH IPXODI
   LH SERVER
   VLM
   CD \
   C:\NWCLIENT\NET LOGIN
         
         NET.CFG:
   
   Link driver EPROODI
      PORT 300
      FRAME Ethernet_802.3
      FRAME Ethernet_802.2
      FRAME Ethernet_II
      FRAME Ethernet_SNAP
   
   NetWare DOS Requester
      FIRST NETWORK DRIVE = F
      NETWARE PROTOCOL = PNW,BIND,NDS
      VLM = NMR.VLM
      VLM = WSSNMP.VLM
      VLM = WSTRAP.VLM
      VLM = WSREG.VLM
      VLM = WSASN1.VLM
      VLM = PNWTRAP.VLM
      VLM = PNWMIB.VLM



*  Third-party trademarks are the property of their respective owners.

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

• Expand the archive file (if the download file is in zip or rar format).

• If the expanded file has an .exe extension, double click it and follow the installation instructions.

• Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

• Find the device and model you want to update in the device list.

• Double-click on it to open the Properties dialog box.

• From the Properties dialog box, select the Driver tab.

• Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.