;--------------------------------------------------------------------------- ; OEMSETUP file for Adaptec DuraLAN Fast Ethernet NIC Driver ; <<FailOver>> ; ; Copyright 1994-1998, Adaptec, Inc. ; ; Supported Windows NT versions: ; 3.51 or 4.0 ; ; Supported Adaptec PCI adapters: ; AIC6915 based boards - ANA6X0XX, ANA62011/TX, ANA62022, ; ANA62044, ANA69011/TX ; ; Usage: ; ; This file is the installation/configuration/deinstallation ; procedure of the Adaptec ADPTSF miniport driver for Windows NT. ; It can be called from Windows Setup directly, or via the Windows ; NT Networks Control Program Applet (NCPA) from inside the Windows ; Control Panel. ; ;--------------------------------------------------------------------------- [Identification] OptionType = NetAdapter [PlatformsSupported] PCI [Options] ANA6XXXX ; Any Adaptec Adptsf-based PCI Fast Ethernet Adapter ANA62011TX ; Single 10/100 Mb/s UTP Port ANA62022 ; 2 each 10/100 Mb/s UTP Port ANA62044 ; 4 each 10/100 Mb/s UTP Port ANA69011TX ; Single 10/100 Mb/s UTP Port [CFIDS] AIC6915CFID = 1763020804 ;; 0x69159004; DeviceID=6915; VendorID=9004 [FileConstants] ;---General--- DRIVERNAME = "" PATH = "" ; DLL/EXE/etc path DRVPATH = "..\..\Windows\i386\" ; Driver path AFAILOVR_NAME = "" ADPTSFDI_NAME = "" UtilityInf = "UTILITY.INF" subroutineinf = "SUBROUTN.INF" SoftwareType = "driver" Exit_Code = 0 sfbmonEXE = $(!STF_WINDOWSSYSPATH)\sfbmon.exe NetEventDLL = "%SystemRoot%\System32\netevent.dll" IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll" Manufacturer = "Adaptec" ProductMajorVersion = "4" ProductMinorVersion = "1" ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion) VendorID = 36868 ;; 9004 OptionHelpFile = "ADPTSFFO.hlp" ;---Software--- ProductSoftwareName = "ADPTSF" ProductSoftwareTitle = "Adaptec DuraLAN Fast Ethernet NIC Driver" NetRuleSoftwareType = "ADPTSFSys ndisDriver ADPTSFDriver" NetRuleSoftwareUse = $(SoftwareType) NetRuleSoftwareBindForm = """ADPTSFSys"" yes no container" NetRuleSoftwareClass = {"ADPTSFDriver basic"} NetRuleSoftwareSWBindable = {"ADPTSFDriver ADPTSFAdapter non exclusive 100"} ;---Hardware--- ProductHardwareName = "ADPTSF" ; Any Adaptec Adptsf-based PCI Fast Ethernet Adapter FunctionANA6XXXXTitle = "Adaptec ANA6X0XX Configuration" ProductHardwareANA6XXXXTitle = "Adaptec DuraLAN NIC" ProductHardwareANA6XXXXDescription = "Adaptec Duralink FailOver for DuraLAN Fast Ethernet NIC" NetRuleHardwareANA6XXXXType = "ADPTSF ADPTSFAdapter" NetRuleHardwareANA6XXXXClass = {"ADPTSFAdapter basic"} AdapterANA6XXXXType = 5 ;; PCI board HelpANA6XXXXId = 10 ; Single 10.100 Mb/s UTP Port FunctionANA62011TXTitle = "Adaptec ANA62011/TX Configuration" ProductHardwareANA62011TXTitle = "Adaptec DuraLAN NIC" ProductHardwareANA62011TXDescription = "Adaptec Duralink FailOver for DuraLAN Fast Ethernet NIC" NetRuleHardwareANA62011TXType = "ADPTSF ADPTSFAdapter" NetRuleHardwareANA62011TXClass = {"ADPTSFAdapter basic"} AdapterANA62011TXType = 5 ;; PCI board HelpANA62011TXId = 10 ; 2 each 10/100 Mb/s UTP Port FunctionANA62022Title = "Adaptec ANA62022 Configuration" ProductHardwareANA62022Title = "Adaptec DuraLAN NIC" ProductHardwareANA62022Description = "Adaptec Duralink FailOver for DuraLAN Fast Ethernet NIC" NetRuleHardwareANA62022Type = "ADPTSF ADPTSFAdapter" NetRuleHardwareANA62022Class = {"ADPTSFAdapter basic"} AdapterANA62022Type = 5 ;; PCI board HelpANA62022Id = 10 ; 4 each 10/100 Mb/s UTP Port FunctionANA62044Title = "Adaptec ANA62044 Configuration" ProductHardwareANA62044Title = "Adaptec DuraLAN NIC" ProductHardwareANA62044Description = "Adaptec Duralink FailOver for DuraLAN Fast Ethernet NIC" NetRuleHardwareANA62044Type = "ADPTSF ADPTSFAdapter" NetRuleHardwareANA62044Class = {"ADPTSFAdapter basic"} AdapterANA62044Type = 5 ;; PCI board HelpANA62044Id = 10 ; Single 10.100 Mb/s UTP Port FunctionANA69011TXTitle = "Adaptec ANA69011/TX Configuration" ProductHardwareANA69011TXTitle = "Adaptec DuraLAN NIC" ProductHardwareANA69011TXDescription = "Adaptec Duralink FailOver for DuraLAN Fast Ethernet NIC" NetRuleHardwareANA69011TXType = "ADPTSF ADPTSFAdapter" NetRuleHardwareANA69011TXClass = {"ADPTSFAdapter basic"} AdapterANA69011TXType = 5 ;; PCI board HelpANA69011TXId = 10 NetRuleHardwareBindForm = " yes yes container" ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion" ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters" ;_DMI begin ServiceKey = "SYSTEM\CurrentControlSet\Services" ;_DMI end [GeneralConstants] from = "" to = "" ExitCodeOk = 0 ExitCodeCancel = 1 ExitCodeFatal = 2 KeyNull = "" MAXIMUM_ALLOWED = 33554432 RegistryErrorIndex = NO_ERROR KeyProduct = "" KeyParameters = "" TRUE = 1 FALSE = 0 NoTitle = 0 ExitState = "Active" OldVersionExisted = $(FALSE) DriverPath = $(!STF_NTPATH)\drivers [date] Now = {} ? $(!LIBHANDLE) GetSystemDate [Identify] read-syms Identification set Status = STATUS_SUCCESSFUL set Identifier = $(OptionType) set Media = #("Source Media Descriptions", 1, 1) Return $(Status) $(Identifier) $(Media) [ReturnOptions] set Status = STATUS_FAILED set OptionList = {} set OptionTextList = {} set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) in $(LanguageList) ifstr(i) $($1) == "" goto returnoptions endif set PlatformList = ^(PlatformsSupported, 1) Ifcontains(i) $($1) in $(PlatformList) goto returnoptions else set Status = STATUS_NOTSUPPORTED goto finish_ReturnOptions endif else set Status = STATUS_NOLANGUAGE goto finish_ReturnOptions endif returnoptions = + Debug-Output "returnoptions ..." set OptionList = ^(Options, 1) set OptionTextList = ^(OptionsText$($0), 1) set Status = STATUS_SUCCESSFUL finish_ReturnOptions = + Debug-Output "finish_ReturnOptions ..." Return $(Status) $(OptionList) $(OptionTextList) [InstallOption] set CurrentVersionValue = "" ; set !DebugOutputControl = 1 OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(!REG_KEY_READ) KeyWinNT ifstr(i) $(KeyWinNT) != "" GetRegValue $(KeyWinNT) "CurrentVersion" CurrentVersionValue CloseRegKey $(KeyWinNT) endif Debug-Output "CurrentVersionValue="$(CurrentVersionValue) set m_WinNTVersion = *($(CurrentVersionValue),4) Debug-Output "m_WinNTVersion = "$(m_WinNTVersion) set Option = $($1) set SrcDir = $($2) set AddCopy = $($3) set DoCopy = $($4) set DoConfig = $($5) set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) NOT-IN $(LanguageList) Return STATUS_NOLANGUAGE endif set-subst LF = "\n" read-syms GeneralConstants read-syms FileConstants read-syms CFIDS set NetRuleSoftwareBindable = $($R1) read-syms DialogConstants$(!STF_LANGUAGE) ifstr(i) $(!NTN_Origination) == "NCPA" set Continue = "OK" endif read-syms FileConstants$(!STF_LANGUAGE) detect date set-title $(Function$(Option)Title) set to = Begin set from = Begin set CommonStatus = STATUS_SUCCESSFUL ifcontains(i) $(m_WinNTVersion) in {"3.50", "3.51"} ; WinNT 3.5x set DRIVERNAME = "ADPTSF30.SYS" set AFAILOVR_NAME = "AFAILOVR35.DLL" set ADPTSFDI_NAME = "ADPTSFDI35.DLL" else ; WinNT 4.x set DRIVERNAME = "ADPTSF40.SYS" set AFAILOVR_NAME = "AFAILOVR40.DLL" set ADPTSFDI_NAME = "ADPTSFDI40.DLL" endif Debug-Output "Exiting Install Options="$(DRIVERNAME) EndWait Begin = + Debug-Output "Begin ..." Debug-Output "BeginDriverName="$(DRIVERNAME) Ifstr(i) $(!NTN_InstallMode) == deinstall set StartLabel = removeadapter else-Ifstr(i) $(!NTN_InstallMode) == Update set StartLabel = UpgradeSoftware else-Ifstr(i) $(!NTN_InstallMode) == bind set StartLabel = bindingadapter else-Ifstr(i) $(!NTN_InstallMode) == configure Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) set from = end set to = end goto nonfatalinfo else set StartLabel = configureadapter endif else set StartLabel = installadapter set OEM_ABANDON_OPTIONS = {} set OEM_ABANDON_SOFTWARE = FALSE set OEM_ABANDON_ON = TRUE endif set from = $(fatal) set to = $(fatal) goto $(StartLabel) installadapter = + Debug-Output "installadapter ..." Debug-Output "installadapter DriverName="$(DRIVERNAME) OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) CloseRegKey $(KeyProduct) ifstr(i) !(NTN_RegBase) == $(ProductKeyName) Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+ $(ProductVersion) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif goto end else Shell $(UtilityInf), CardExistedDlg ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) != "OK" set CommonStatus = STATUS_USERCANCEL goto end endif set OldVersionExisted = $(TRUE) endif Endif ifstr(i) $(DoCopy) == "YES" Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) endif goto installproduct configureadapter = + Debug-Output "configureadapter ..." Ifstr(i) $(KeyProduct) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Goto fatalregistry Endif Endif Shell $(UtilityInf) FindService, $(KeyProduct) Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Endif Ifstr(i) $($R0) != NO_ERROR Goto fatalregistry endif set KeyParameters = $($R2) CloseRegKey $($R1) Ifstr $(KeyParameters) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE goto fatalregistry endif set OldVersionExisted = $(TRUE) set ValueName = "" set ValueData = "" set ValueStr = "" set ValueList = {} ; ; Added for FailOver ; ; Hard-code the ConnectionType to Auto-Detect for Unattended-install ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" set ConnectionValue = *($(ConnectionList), 1) goto adapteroptions endif ; ; Get the Network Adapter Number ; GetRegValue $(KeyParameters) "AdapterNumber" AdapterNumberData ifint $(!RegLastError) == 0 set AdapterNumber = *($(AdapterNumberData),4) else Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "NONFATAL" ,"Unable to get Adapter Number from registry" set CommonStatus = STATUS_USERCANCEL goto end endif LoadLibrary "Adaptec ADPTSF Driver Disk" $(!STF_WINDOWSSYSPATH)"\"ADPTSFFO.DLL LibHandle Debug-Output "Invoking EmPCIConfig : AdapterNumber="$(AdapterNumber) LibraryProcedure DLLResponse $(LibHandle) EmPCIConfig $(AdapterNumber) FreeLibrary $(LibHandle) ifstr(i) $(DLLResponse) == 99 set CommonStatus = STATUS_USERCANCEL goto end endif adapteroptions = + Debug-Output "adapteroptions ..." set from = adapteroptions ifstr(i) $(!NTN_InstallMode) == configure ;_DMI begin ; ; SNMPINstallStatus = 0 - means SNMP is installed ; = 1 - NT SNMP is not present ; = 2 - SNMP Agent is configured already ; set SNMPInstallStatus = "9" set MibName = "FailoverMib" set MibFileName = "afailovr.dll" install "InstallSNMPagent" ifstr $(SNMPInstallStatus) == "1" ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" goto successful endif Shell "subroutn.inf" SetUpMessage $(!STF_LANGUAGE) NONFATAL "SNMP Service is not installed. To activate SNMP and Adaptec network management features on this system,"+ " install the NT SNMP Service. On the network management station,"+ " use the configure option to configure Server related MIBs." goto successful endif ifstr $(SNMPInstallStatus) == "0" Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "NONFATAL", "Configured Failover agent" endif ;_DMI end goto successful endif ; installproduct =+ Debug-Output "installproduct ..." Debug-Output "Print Driver Name = "$(DRIVERNAME) StartWait set ProductSoftwareImagePath = "\SystemRoot\system32\drivers\"$(DRIVERNAME) ; ifint $(OldVersionExisted) == $(FALSE) Ifstr(i) $(DoCopy) == "YES" Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) Endif install "Install-Option" install "Install-Hlp" ; ; Added for FailOver ; install "Install-Dll" install "Install-Agents" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal endif Debug-Output "Installproduct DriverName="$(DRIVERNAME) Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), + $(ProductSoftwareName), + $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), + $(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+ $(NetEventDLL) Set OEM_ABANDON_SOFTWARE = TRUE ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR" EndWait CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) CloseRegKey $($R4) CloseRegKey $($R5) goto fatalregistry endif Set SoftProductKey = $($R1) Set SoftNetRuleKey = $($R2) Set SoftServiceKey = $($R3) Set SoftParameterKey = $($R4) Set SoftLinkageKey = $($R5) set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+ {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+ {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+ {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR" EndWait CloseRegKey $(SoftProductKey) CloseRegKey $(SoftNetRuleKey) CloseRegKey $(SoftServiceKey) CloseRegKey $(SoftParameterKey) CloseRegKey $(SoftLinkageKey) goto fatalregistry endif set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+ {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, + {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, + {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareSWBindable)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) CloseRegKey $(SoftProductKey) CloseRegKey $(SoftNetRuleKey) CloseRegKey $(SoftServiceKey) CloseRegKey $(SoftParameterKey) CloseRegKey $(SoftLinkageKey) Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR" EndWait goto fatalregistry endif endif ;---------------------------------- ;search for all CFIDs we support ;---------------------------------- set AdapterFound = $(FALSE) set CFIDList = ^(CFIDS, 1) ForListDo $(CFIDList) set CurrCFID = $($) Debug-Output "ADPTSF: Current CFID="$(CurrCFID) set-div DeviceID = $(CurrCFID) 65536 Shell $(UtilityInf), GetPCIInformation, $(VendorID) $(DeviceID) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R0) != {} set AdapterList = $($R0) set AdapterFound = $(TRUE) ;---------------------------------- ;search for CFID based PCI adapters ;---------------------------------- ForListDo $(AdapterList) set BusNum = *($($),1) set DeviceNum = *($($),2) set FunctionNum = *($($),3) Debug-Output "ADPTSF: BusNum="$(BusNum)" DeviceNum="$(DeviceNum) Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(BusNum), + $(DeviceNum), $(ProductHardware$(Option)Description), $(ProductHardwareName) "YES" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr $($R0) != "NO_ERROR" set Error = $($R0) goto fatal endif ifstr(i) $($R1) != "YES" Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName) ifint $($R4) != -1 Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4)) endif ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR" EndWait CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) goto fatalregistry endif Set HardNetCardKey = $($R1) Set HardNetRuleKey = $($R2) Set HardParameterKey = $($R3) set AdapterNumber = $($R4) set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+ {Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+ {ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(HardNetCardKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set BusTypeNum = 5 ; ; Added AdapterNumber for FailOver ; set NewValueList = {{AdapterType,$(NoTitle),$(!REG_VT_DWORD),$(Adapter$(Option)Type)},+ {MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+ {AdapterNumber,$(NoTitle),$(!REG_VT_DWORD),$(AdapterNumber)},+ {BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+ {AdapterCFID,$(NoTitle),$(!REG_VT_DWORD),$(CurrCFID)}} Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)"""" set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm) set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardware$(Option)Type)},+ {bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardware$(Option)Class)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(HardNetRuleKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif CloseRegKey $(HardNetCardKey) CloseRegKey $(HardNetRuleKey) set NewValueList = {{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNum)},+ {SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(DeviceNum)},+ {FunctionNumber,$(NoTitle),$(!REG_VT_DWORD),$(FunctionNum)}} Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList) CloseRegKey $(HardParameterKey) endif EndForListDo ;$(AdapterList) endif ;ifstr(i) $($R0) != {} EndForListDo ;$(CFIDList) ifint $(AdapterFound) == $(FALSE) set Error = $(CANNOT_FIND_ANY_CARD) set CommonStatus = STATUS_USERCANCEL goto fatal endif ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" goto SkipEmPCIConfig endif LoadLibrary "Adaptec ADPTSF Driver Disk" $(!STF_WINDOWSSYSPATH)"\"ADPTSFFO.DLL LibHandle Debug-Output "Invoking EmPCIGetConnType" LibraryProcedure DLLResponse $(LibHandle) EmPCIGetConnType ifstr(i) $(DLLResponse) == 99 set CommonStatus = STATUS_USERCANCEL FreeLibrary $(LibHandle) goto abandon endif FreeLibrary $(LibHandle) LoadLibrary "Adaptec ADPTSF Driver Disk" $(!STF_WINDOWSSYSPATH)"\"ADPTSFFO.DLL LibHandle set AdapterNumber = 0 Debug-Output "Invoking EmPCIConfig : AdapterNumber="$(AdapterNumber) LibraryProcedure DLLResponse $(LibHandle) EmPCIConfig $(AdapterNumber) FreeLibrary $(LibHandle) SkipEmPCIConfig =+ EndWait ;_DMI begin ; DMI Install must be done before SFBMON service is started to avoid race conditions ; in registry updates! - JTJ Debug-Output "InstallSNMPagent" set SNMPInstallStatus = "0" set MibName = "FailoverMib" set MibFileName = "afailovr.dll" install "InstallSNMPagent" ifstr $(SNMPInstallStatus) == "1" ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" goto install_sfbmon endif Shell "subroutn.inf" SetUpMessage $(!STF_LANGUAGE) NONFATAL "SNMP Service is not installed. To activate SNMP and Adaptec network management features on this system,"+ " install the NT SNMP Service. On the network management station,"+ " use the configure option to configure Server related MIBs." goto install_sfbmon endif ;_DMI end install_sfbmon =+ ; ; If sfbmon service is already install, skip registry update. ; OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\sfbmon" $(!REG_KEY_QUERY_VALUE) ServicesHandle ifstr $(ServicesHandle) != $(KeyNull) Debug-Output "SFBMON service already installed!" CloseRegKey $(ServicesHandle) goto successful endif ; ; Execute sfbmon to install the sfbmon daemon service and to monitor any ; changes to Driver's Linkage Key ; StartDetachedProcess ExitCode "" "" $(sfbmonEXE) ifstr $(ExitCode) != "0" Debug-Output "Cannot start SFBMON service program!" Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL" ,"Cannot start Adaptec SFBMON service program!" ; ; remove the failover backup monitor service ; OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services" $(!REG_KEY_ALL_ACCESS) ForbmonHandle ifstr $(ForbmonHandle) != $(KeyNull) DeleteRegTree $(ForbmonHandle) "sfbmon" CloseRegKey $(ForbmonHandle) endif goto fatal endif goto successful updateparameters =+ Debug-Output "updateparameters ..." set HardParameterKey = $($R3) set NewValueList = {{ConnectionType,$(NoTitle),$(!REG_VT_DWORD),$(ConnectionValue)}} Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif CloseRegKey $(KeyParameters) goto successful bindingadapter =+ Debug-Output "bindingadapter ..." set Error = "Binding: Sorry, not yet implemented." goto fatal removeadapter = + Debug-Output "removeadapter ..." ; ; Added for FailOver ; Ifstr $(KeyProduct) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find component product key" goto fatalregistry Endif Endif Debug-Output "INF: Shelling to FindService" Shell $(UtilityInf) FindService, $(KeyProduct) Ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "INF: FindService shell failure" Goto ShellCodeError Endif Ifstr(i) $($R0) != NO_ERROR Debug-Output "INF: FindService Shell error: "$($R0) Goto fatalregistry endif set KeyParameters = $($R2) CloseRegKey $($R1) Ifstr $(KeyParameters) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find component service" goto fatalregistry endif ; ; Get the Adapter Number for this adapter ; GetRegValue $(KeyParameters) "AdapterNumber" AdapterNumberData ifint $(!RegLastError) == 0 set AdapterNumber = *($(AdapterNumberData),4) else Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "NONFATAL" ,"Unable to get Adapter Number from registry" set CommonStatus = STATUS_USERCANCEL goto end endif LoadLibrary "Adaptec ADPTSF Driver Disk" $(!STF_WINDOWSSYSPATH)"\"ADPTSFFO.DLL LibHandle Debug-Output "Invoking EmPCIRemoveLinks : AdapterNumber="$(AdapterNumber) LibraryProcedure DLLResponse $(LibHandle) EmPCIRemoveLinks $(AdapterNumber) FreeLibrary $(LibHandle) ; ; Get the reference count for the adapter ; OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\"$(Manufacturer)\$(ProductSoftwareName)"\CurrentVersion" $(!REG_KEY_ALL_ACCESS) RefCountHandle ifstr $(RefCountHandle) == $(KeyNull) set RegistryErrorIndex = UNABLE_OPEN_MICROSOFT_KEY Debug-Output "Cannot open Adaptec Key" goto fatalregistry endif GetRegValue $(RefCountHandle) "RefCount" RefCountData ifint $(!RegLastError) == 0 set RefCount = *($(RefCountData),4) else Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "NONFATAL" ,"Unable to get Reference count" endif ; ; Get the inffile associated with this adapter ; OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\"$(Manufacturer)\$(ProductSoftwareName)"\CurrentVersion\NetRules" $(!REG_KEY_ALL_ACCESS) InfNameHandle ifstr $(InfNameHandle) == $(KeyNull) set RegistryErrorIndex = UNABLE_OPEN_MICROSOFT_KEY Debug-Output "Cannot open Adaptec Key" goto fatalregistry endif GetRegValue $(InfNameHandle) "InfName" InfNameData ifint $(!RegLastError) == 0 set InfName = *($(InfNameData),4) ifint $(RefCount) == 1 AddFileToDeleteList $(!STF_WINDOWSSYSPATH)\$(InfName) endif endif CloseRegKey $(InfNameHandle) Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif else Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $(!NTN_RegBase) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif ; ; Added for FailOver ; ifint $(RefCount) == 1 AddFileToDeleteList $(!STF_WINDOWSSYSPATH)\drivers\$(DRIVERNAME) AddFileToDeleteList $(!STF_WINDOWSSYSPATH)\ADPTSFFO.DLL AddFileToDeleteList $(!STF_WINDOWSSYSPATH)\ADPTSFFO.HLP AddFileToDeleteList $(!STF_WINDOWSSYSPATH)\ADPTSFFO.CNT ; The following SNMP agent file is used by both the EMPCI and ADPTSF ; drivers. This should not be deleted if either driver is on the ; system. Management has requested that the effort spent on ; dual driver support should be minimized. As a result, the ; the solution to this problem is to leave afailovr.dll on the ; AddFileToDeleteList $(!STF_WINDOWSSYSPATH)\AFAILOVR.DLL AddFileToDeleteList $(!STF_WINDOWSSYSPATH)\SFBMON.EXE AddFileToDeleteList $(!STF_WINDOWSSYSPATH)\ADPTSFDI.DLL ; ; should be LIFO basis ; set MibName = "DmiMib" install "RemoveSNMPagent" set MibName = "FailoverMib" install "RemoveSNMPagent" ; ; remove the failover backup monitor service ; OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services" $(!REG_KEY_ALL_ACCESS) ForbmonHandle ifstr $(ForbmonHandle) != $(KeyNull) DeleteRegTree $(ForbmonHandle) "sfbmon" CloseRegKey $(ForbmonHandle) endif endif goto end UpgradeSoftware = + Debug-Output "UpgradeSoftware ..." OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set !UG_Filename = $($R0) install "Install-Update" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS goto fatal endif SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)} SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)} CloseRegKey $(KeyProduct) else goto fatalregistry endif goto end successful = + Debug-Output "successful ..." goto end abandon = + Debug-Output "abandon ..." ForListDo $(OEM_ABANDON_OPTIONS) Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $($) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif EndForListDo Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), FALSE ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end warning = + Debug-Output "warning ..." Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(to) else-ifstr(i) $($R1) == "CANCEL" goto $(from) else goto "end" endif nonfatalinfo = + Debug-Output "nonfatalinfo ..." Set CommonStatus = STATUS_USERCANCEL Set Severity = STATUS goto nonfatalmsg nonfatal = + Debug-Output "nonfatal ..." Set Severity = NONFATAL goto nonfatalmsg nonfatalmsg = + Debug-Output "nonfatalmsg ..." ifstr(i) $(Error) == "" Set Severity = NONFATAL Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(from) else goto "end" endif fatalregistry = + Debug-Output "fatalregistry ..." Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal fatal = + Debug-Output "fatal ..." ifstr(i) $(Error) == "" Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif goto setfailed ShellCodeError = + Debug-Output "ShellCodeError ..." set DlgType = "MessageBox" set STF_MB_TITLE = $(ShellCodeErrorTitle) set STF_MB_TEXT = $(ShellCodeErrorText) set STF_MB_TYPE = 1 set STF_MB_ICON = 3 set STF_MB_DEF = 1 ui start "Error Message" goto setfailed setfailed = + Debug-Output "setfailed ..." set CommonStatus = STATUS_FAILED Debug-Output "OEM_ABANDON_ON="$(OEM_ABANDON_ON) ifstr(i) $(OEM_ABANDON_ON) == TRUE set OEM_ABANDON_ON = FALSE goto abandon endif goto end end = + Debug-Output "end ..." goto term term = + Debug-Output "term ..." Return $(CommonStatus) [Install-Option] Debug-Output "[Install-Option] ..." Debug-Output "SelectedOption="$(Option) Debug-Output "SelectedDriver="$(DRIVERNAME) set STF_VITAL = "" ifstr(i) $(AddCopy) == "YES" AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers endif ifstr(i) $(DoCopy) == "YES" set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList endif Exit [Install-Hlp] Debug-Output "[Install-Hlp] ..." set STF_VITAL = "" AddSectionFilesToCopyList Files-Hlp $(SrcDir) $(!STF_WINDOWSSYSPATH) set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList Exit ; ; Added for FailOver ; [Install-DLL] Debug-Output "[Install-DLL] ..." set STF_VITAL = "" AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH) set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList Exit [Install-Agents] Debug-Output "[Install-Agents] ..." set STF_VITAL = "" AddSectionFilesToCopyList Files-Agent $(SrcDir) $(!STF_WINDOWSSYSPATH) set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList Exit [InstallSNMPagent] Debug-Output "[InstallSNMPagent] ..." ; ; Make an entry under HKEY_LOCAL\System\CurrentControlSet\Services ; OpenRegKey $(!REG_H_LOCAL) "" $(ServiceKey) $(!REG_KEY_CREATE_SUB_KEY) ServicesHandle ifstr $(ServicesHandle) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find services under CurrentControlSet" Exit endif ; ; check if the service SNMP already existing ; OpenRegKey $(ServicesHandle) "" "SNMP" $(!REG_KEY_CREATE_SUB_KEY) SNMPHandle ifstr $(SNMPHandle) == $(KeyNull) set SNMPInstallStatus = "1" exit endif ; ; add the value for the ExtensionAgents ; OpenRegKey $(SNMPHandle) "" "Parameters\ExtensionAgents" $(!REG_KEY_ALL_ACCESS) SNMPExtensionHandle EnumRegValue $(SNMPExtensionHandle) SNMPExtValueList ifint $(!RegLastError) != 0 Exit endif ; ; Look if there is already an entry for SNMP Agent ; set MaxSNMPIndex = "0" ForListDo $(SNMPExtValueList) set CurrentSNMPVal = *($($), 4) ifstr(i) $(CurrentSNMPVal) == "SOFTWARE\"$(Manufacturer)"\"$(MibName)"\CurrentVersion" set SNMPInstallStatus = "2" Exit endif ;Set index to largest index number read so far. ;This handles string ordering of index numbers (e.g 10 before 2) ifint *($($), 1) > $(MaxSNMPIndex) set MaxSNMPIndex = *($($), 1) endif EndForListDo ; Add new entry index after the largest one in list set-add MaxSNMPIndex = $(MaxSNMPIndex), 1 SetRegValue $(SNMPExtensionHandle) {$(MaxSNMPIndex), 0, $(!REG_VT_SZ), "SOFTWARE\"$(Manufacturer)"\"$(MibName)"\CurrentVersion"} ifint $(!RegLastError) != 0 Shell "subroutn.inf" SetUpMessage $(!STF_LANGUAGE) NONFATAL "SetRegValue failed" Exit endif CloseRegKey $(SNMPExtensionHandle) CloseRegKey $(SNMPHandle) CloseRegKey $(ServicesHandle) ; ; Make an entry under HKEY_LOCAL\SOFTWARE\$(Manufacturer) ; OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\"$(Manufacturer) $(!REG_KEY_CREATE_SUB_KEY) SNMPSoftwareHandle ifstr $(SNMPSoftwareHandle) == $(KeyNull) Exit endif ; ; Check if the key $(MibName) is already there ; OpenRegKey $(SNMPSoftwareHandle) "" $(MibName) $(!REG_KEY_CREATE_SUB_KEY) SNMPAdaptecHandle ifstr $(SNMPAdaptecHandle) == $(KeyNull) CreateRegKey $(SNMPSoftwareHandle) {$(MibName), 0, GenericClass} "" $(!REG_KEY_CREATE_SUB_KEY) "" SNMPAdaptecHandle ifstr $(SNMPAdaptecHandle) == $(KeyNull) Debug-Output "Cannot create subkey Under Adaptec" Exit endif endif ; ; Check if the key "CurrentVersion" is already there ; OpenRegKey $(SNMPAdaptecHandle) "" "CurrentVersion" $(!REG_KEY_SET_VALUE) SNMPCurrentHandle ifstr $(SNMPCurrentHandle) == $(KeyNull) CreateRegKey $(SNMPAdaptecHandle) {"CurrentVersion", 0, GenericClass} "" $(!REG_KEY_SET_VALUE) "" SNMPCurrentHandle ifstr $(SNMPCurrentHandle) == $(KeyNull) Debug-Output "Cannot create subkey Under FailoverMib" Exit endif endif ; ; Set the values ; SetRegValue $(SNMPCurrentHandle) {"Pathname", 0, $(!REG_VT_EXPAND_SZ), "%SystemRoot%\System32\"$(MibFileName)} ifint $(!RegLastError) != 0 Debug-Output "Cannot add the name-value pair" Exit endif CloseRegKey $(SNMPCurrentHandle) CloseRegKey $(SNMPAdaptecHandle) CloseRegKey $(SNMPSoftwareHandle) set SNMPInstallStatus = "0" Exit [RemoveSNMPagent] Debug-Output "[RemoveSNMPagent] ..." ; ; Open HKEY_OCAL\System\CurrentControlSet\Services ; OpenRegKey $(!REG_H_LOCAL) "" $(ServiceKey) $(!REG_KEY_CREATE_SUB_KEY) ServicesHandle ifstr $(ServicesHandle) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find services under CurrentControlSet" Exit endif ; ; check if the service SNMP already existing ; OpenRegKey $(ServicesHandle) "" "SNMP" $(!REG_KEY_CREATE_SUB_KEY) SNMPHandle ifstr $(SNMPHandle) == $(KeyNull) exit endif ; ; Remove the value for the ExtensionAgents ; OpenRegKey $(SNMPHandle) "" "Parameters\ExtensionAgents" $(!REG_KEY_ALL_ACCESS) SNMPExtensionHandle EnumRegValue $(SNMPExtensionHandle) SNMPExtValueList ifint $(!RegLastError) != 0 Exit endif ; ; Look if there is already an entry for SNMP Agent ; Delete the registry value corresponding to the SNMP Agent ; ForListDo $(SNMPExtValueList) set CurrentSNMPVal = *($($), 4) set CurrentSNMPValName = *($($), 1) ifstr(i) $(CurrentSNMPVal) == "SOFTWARE\"$(Manufacturer)"\"$(MibName)"\CurrentVersion" DeleteRegValue $(SNMPExtensionHandle) $(CurrentSNMPValName) endif EndForListDo ; ; Remove $(MibName) entry from SOFTWARE/$(Manufacturer) ; OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\"$(Manufacturer) $(!REG_KEY_ALL_ACCESS) ProductHandle ifstr $(ProductHandle) != $(KeyNull) DeleteRegTree $(ProductHandle) $(MibName) endif Exit [Install-Update] set STF_VITAL = "" set STF_OVERWRITE = "VERIFYSOURCEOLDER" ; ; Added for FailOver ; AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH) AddSectionFilesToCopyList Files-Hlp $(SrcDir) $(!STF_WINDOWSSYSPATH) AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH) ;_DMI begin AddSectionFilesToCopyList Files-Agent $(SrcDir) $(!STF_WINDOWSSYSPATH) ;_DMI end AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList exit [Source Media Descriptions] 1 = "Drivers for Microsoft Operating Systems" [ProductType] STF_PRODUCT = Winnt ;STF_PLATFORM = I386 ;STF_PLATFORM = Alpha ;STF_PLATFORM = ppc ;STF_PLATFORM = MIPS [Files-Inf] 1,oemsetup.inf , SIZE=1000, RENAME=$(!UG_Filename) [Files-ANA6XXXX] 1,$(DRVPATH)$(DRIVERNAME) , SIZE=999, RENAME=$(DRIVERNAME) [Files-ANA62011TX] 1,$(DRVPATH)$(DRIVERNAME) , SIZE=999, RENAME=$(DRIVERNAME) [Files-ANA62022] 1,$(DRVPATH)$(DRIVERNAME) , SIZE=999, RENAME=$(DRIVERNAME) [Files-ANA62044] 1,$(DRVPATH)$(DRIVERNAME) , SIZE=999, RENAME=$(DRIVERNAME) [Files-ANA69011TX] 1,$(DRVPATH)$(DRIVERNAME) , SIZE=999, RENAME=$(DRIVERNAME) [Files-Hlp] 1,$(PATH)ADPTSFFO.HLP , SIZE=999, RENAME=ADPTSFFO.HLP 1,$(PATH)ADPTSFFO.CNT , SIZE=999, RENAME=ADPTSFFO.CNT ; ; Added for FailOver ; [Files-Dll] 1,$(PATH)ADPTSFFO.DLL , SIZE=120000, RENAME=ADPTSFFO.DLL 1,$(PATH)SFBMON.EXE , SIZE=78000, RENAME=SFBMON.EXE ;_DMI begin [Files-Agent] 1,$(PATH)$(AFAILOVR_NAME) , SIZE=120000, RENAME=AFAILOVR.DLL 1,$(PATH)$(ADPTSFDI_NAME) , SIZE=120000, RENAME=ADPTSFDI.DLL ;_DMI end [LanguagesSupported] ENG [OptionsTextENG] ANA6XXXX = "Adaptec DuraLAN Fast Ethernet NIC" ANA62011TX = "Adaptec ANA-62011/TX Fast Ethernet NIC" ANA62022 = "Adaptec ANA-62022 Fast Ethernet NIC" ANA62044 = "Adaptec ANA-62044 Fast Ethernet NIC" ANA69011TX = "Adaptec ANA-69011/TX Fast Ethernet NIC" [FileConstantsENG] ProCaption = "Windows NT Setup" ProCancel = "Cancel" ProCancelMsg = "Windows NT Networking is not correctly installed. "+ "Are you sure you want to cancel copying files?" ProCancelCap = "Network Setup Message" ProText1 = "Copying:" ProText2 = "To:" ProductSoftwareDescription = "Adaptec DuraLAN Fast Ethernet NIC Driver" ConnectionList = ^(ConnectionChoices$(Option), 1) ConnectionValues = ^(ConnectionChoices$(Option), 2) NoList = ^(NoChoices, 1) NoValues = ^(NoChoices, 2) ShellCodeErrorTitle = "Error: "$(Function$(Option)Title) ShellCodeErrorText = "Shell Code Error." CANNOT_FIND_ANY_CARD = "Network card is not present in the system" [DialogConstantsENG] Help = "&Help" Exit = "Cancel" OK = "OK" HelpContext = "" Continue = "Continue" Cancel = "Cancel" [FileDependentDlgENG] DlgText = "Choose the proper connection type for the "+ "network adapter. Select [Help] for a detailed "+ "description of the available options." DlgTemplate = "ADAP_PROTO_COMBO" DlgType = "Combination" Caption = $(Function$(Option)Title) Combo1Label = "&Connection Type:" Combo1List = $(ConnectionList) Combo1Out = $(ConnectionValue) ComboListItemsIn = {Combo1List} ComboListItemsOut = {Combo1Out} EditTextLim = "" CBOptionsGreyed = {} MinHelpId = 10 MaxHelpId = 30 HelpContext = $(Help$(Option)Id)Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.