1. pcmcia.zip Driver
2. VINES.TXT File Contents

VINES.TXT Driver File Contents (pcmcia.zip)

NDIS Driver for Banyan VINES Installation

Introduction:
-------------
This document describes the procedure to setup the Banyan VINES for
PCMCIA/CT II Ethernet card.

Before you start with the installation process, make sure that
the Card Manager software has been successfully installed. For
information on installing the Card Manager software, please refer
to the appropriate readme file, your Ethernet Adapter manual, or
your computer manufacturer.

Location of Driver:	\VINES\PCM200.DOS
------------------

To install Banyan VINES 5.xx software on a DOS base workstation, follow the
instructions.  DOS must be installed on the target workstation C: drive, or
you must have a bootable DOS floppy diskette.

1. Installation Porcedure:
   a.  Use the DOS MD command to create a subdirectory called \VINES.

   b.  Copy the contents of the VINES LAN S/W (DOS) Install diskette
       into the \VINES subdirectory.

   c.  Copy the contents of the NDIS subdirectory on the VINES LAN S/W
       (DOS) 2 of 2 diskette into the \VINES subdirectory.

   d.  Copy all files from \MSLANMAN.DOS\DRIVERS\ETHERNET\PCM200
       subdirectory on the driver diskette to the \VINES subdirectory.

   e.  Edit the PROTOCOL.INI file to read as follows:

       [PROTOCOL MANAGER]
       DRIVERNAME = PROTMAN$

       [VINES_XIF]
       DRIVERNAME = NDISBAN$
       BINDINGS = PCM200

       [PCM200]
       IOBASE = 0x300
       INTERRUPT = 5
       DRIVERNAME = PCM200$

   f.  Run the PCCONFIG.EXE program located in the \VINES subdirectory.

   g.  Select option 1, Network Card Settings.

   h.  Select the "NDIS Ethernet" option.

   i.  The NDIS workstation screen appears.  Enter the IRQ that you
       selected for the PCMCIA/CT II adapter.

   j.  Press 'F10' when done, press <ESC> to exit this screen.

   k.  Select "2 - Login Environment Settings. ", Press <Enter>.

   l.  Select "1 - Select Default Communications Driver. ", Press <Enter>.

   m.  Choose "NDIS Ethernet", Press <ESC> to exit this menu.

   n.  Edit the CONFIG.SYS file and add the following lines, substituting
       A: for C: for a floppy diskette installation.

       DEVICE=C:\VINES\PROTMAN.DOS /I:C:\VINES
       DEVICE=C:\VINES\PCM200.DOS

   o.  Add the BAN command to the AUTOEXEC.BAT file.  BAN loads the NDISBAN
       drivers and reads the PCCONFIG.DB file to invoke changes made during
       the PCCONFIG stage.


Before installing the PCMCIA/CT II Ethernet LAN into workstation, you
have to append the following lines into config.sys and protocol.ini
file or it would look like the following.

     < Sample CONFIG.SYS file >

	   DEVICE=C:\DOS\SETVER.EXE
	   DEVICE=C:\DOS\HIMEM.SYS
	   DEVICE=C:\DOS\EMM386.EXE X=D000-D0FF RAM NOEMS
	   DOS=HIGH,UMB
	   FILES=30
	   BUFFERS=20
	   REM CardSoft(TM) 3.1 PCMCIA DRIVERS
	   DEVICEHIGH=C:\CARDSOFT\SS365SL.EXE
	   DEVICEHIGH=C:\CARDSOFT\CS.EXE  /POLL:1
	   DEVICEHIGH=C:\CARDSOFT\CSALLOC.EXE
	   DEVICEHIGH=C:\CARDSOFT\CARDID.EXE
	   DEVICEHIGH=C:\CARDSOFT\ECARDCS.EXE /IRQ=5 /IO=300
	   STACKS=9,256
	   LASTDRIVE=Z
	   DEVICE=C:\VINES\PROTMAN.DOS /I:C:\VINES
	   DEVICE=C:\VINES\PCM200.DOS
	      :
	      :

     <Sample PROTOCOL.INI file >

	      :
	      :
	   [PROTOCOL MANAGER]
	   DRIVERNAME = PROTMAN$

	   [VINES_XIF]
	   DRIVERNAME = NDISBAN$
	   BINDINGS = PCM200

	   [PCM200]
	   IOBASE = 0x300
	   INTERRUPT = 5
	   DRIVERNAME = PCM200$