1. Pcmcia.zip Driver
2. PACKET.TXT File Contents

PACKET.TXT Driver File Contents (Pcmcia.zip)

Packet Driver

Introduction:
-------------
This document describes the procedure to setup the Packet driver for
PCMCIA/CT II Ethernet card.

Before you start with the installation process, make sure that
the Card Manager software has been successfully installed. For
information on installing the Card Manager software, please refer
to the appropriate readme file, your Ethernet Adapter manual, or
your computer manufacturer.

Location of Driver:	\PACKET\PCM200.COM
------------------

Install procedure:
------------------
   1. Load the packet driver using the software interrupt and any
      optional switches if required.

      Usage: PCM200 [options] <packet_int_no> <int_level> <io_addr>
      Example: PCM200 -i 0x60 0x5 0x300

      The only required parameter is the software interrupt. A packet
      driver needs to have a software interrupt assigned to it for other
      programs to access it. The recommended interrupt 0x60. If you need
      any of the options listed below, place them before the software
      interrupt on the command line.

      -i - Force driver to report itself as 802.3 instead of Ethernet II.
      -d - Delayed initialization. Used for diskless booting
      -n - NetWare conversion. Converts 802.3 packets into 8137 packets
      -w - Windows hack, obsoleted by winpkt
      -p - Promiscuous mode disable
      -h - Help
      -u - Uninstall

   2. This is an auto sensing packet driver.  That means it will auto-
      matically scan the system until it finds the adapter I/O address
      and IRQ. The software interrupt will still need to be given in the
      command line when invoking the packet driver.(if not be given, the
      default value is 0x60)

   3. Run PCM200.COM, the screen will appear following message:

      Packet driver for PCMCIA/CT II Ethernet Card, version 11.4.3
      Conforming to PC/FTP Packet Driver Spec. v1.09.

      System: [345]86 processor, ISA bus, Two 8259s
      Packet driver software interrupt is 0x60 (96)
      Interrupt number 0x5 (5)
      I/O port 0x300 (768)
      Ethernet address is 00:00:1C:CB:C9:26

   4. Now,You are ready to use FTP's PC/TCP and its related functions.

Before installing the PCMCIA/CT II Ethernet LAN into workstation, you
have to append the following lines into config.sys and autoexec.bat
file or it would look like the following.

     < Sample CONFIG.SYS file >

	   DEVICE=C:\DOS\SETVER.EXE
	   DEVICE=C:\DOS\HIMEM.SYS
	   DEVICE=C:\DOS\EMM386.EXE X=D000-D0FF RAM NOEMS
	   DOS=HIGH,UMB
	   FILES=30
	   BUFFERS=20
	   REM CardSoft(TM) 3.1 PCMCIA DRIVERS
	   DEVICEHIGH=C:\CARDSOFT\SS365SL.EXE
	   DEVICEHIGH=C:\CARDSOFT\CS.EXE  /POLL:1
	   DEVICEHIGH=C:\CARDSOFT\CSALLOC.EXE
	   DEVICEHIGH=C:\CARDSOFT\CARDID.EXE
	   DEVICEHIGH=C:\CARDSOFT\ECARDCS.EXE /IRQ=5 /IO=300
	   STACKS=9,256
	   LASTDRIVE=Z

     < Sample AUTOEXEC.BAT file >

	   @ECHO OFF
	   PROMPT $p$g
	   PATH C:\DOS;C:\PCTCP;
	   PCM200 -i 0X60 0x5 0x300
	   ETHDRV

Note: Since the default software interrupt is 0x60, IRQ is 5, I/O Port is 300.
      The file ETHDRV.EXE developed by FTP Software, Inc.It must be installed
      beforehand.