1. RN303F.ZIP Driver
2. README.TXT File Contents

README.TXT Driver File Contents (RN303F.ZIP)

    SCO OpenServer 5.0 MDI driver for MXIC PCI Fast Ethernet Adapters
    =================================================================

     Your Driver Diskette should contain the following files in the 
     subdirectory \SCO-UNIX\MDIDRV:

--------------------------------------------------------------------
Files           Contents                                                                                                 
--------------------------------------------------------------------
readme.txt      Text file about driver installation for the
		SCO OpenServer 5.0.

metfdrv.100     MXIC PCI Fast Ethernet Adapters MDI driver
		package for SCO OpenServer 5.0.
--------------------------------------------------------------------

A. Introduction.
----------------
    This is a SCO OpenServer 5.0 MDI driver for MXIC PCI Fast
    Ethernet Adapters whose released version is 1.0.0.  It is
    installed by "custom" and configured by using "netconfig"
    command.

    The MDI driver requires the following hardware and software:

    - MXIC PCI Fast Ethernet Adapters.

    - SCO OpenServer 5.0 or above.


B. Installation Procedure.
--------------------------

1. Prepare a formatted diskette on any DOS machine.  For example, type:

   C>format a:

2. Now boot the SCO OpenServer 5.0 and enter the Maintenance mode.

   Please follow the instructions below to uncompress the package
   file:

   > cd /tmp   (and inserts the package floppy in the proper drive,
		 i.e. drive A:)

   > doscp a:/sco-unix/mdidrv/metfdrv.100 metftar

   > then replaces with the prepared formatted diskette done in step 1.

   > dd if=metftar of=/dev/rfd0135ds18
     (Note: Use another device file name if you use a different
	    floppy drive.)

   > Now the package installation diskette is ready for installing.


3. The following sections describe the configuration of the driver. 
   It is suggested that you should perform these instructions in the 
   singler-user environment (maintenance mode).

   3.1. Run "custom" command and select the "Install New..." option
	under "Software" item. It will prompt you "Installing:
	METF 10/100TX PCI Adapter MDI Driver (ver 1.0.0)" and
	then choose the "FULL" option to install this package.

	After running the "custom" utility and the new package is
	installed, you should use  the "netconfig" command to add
	the driver into your system like the step 4 below.

   3.2. Run "netconfig" to add the desired LAN adapter. The steps
	for adding the new LAN adapter are listed below:

	a. When the "Network Configuration Manager" is shown, please
	   select "Add new LAN adapter" option under "Hardware" main
	   item. 
   
	b. When the screen "Add new LAN Adapter" is shown, then select
	   the option "Configure hardware not listed above... ]". 

	c. After "Select network adapter to be added:" is shown, please  
	   select  the  "METF 10/100TX PCI Adapter MDI Driver"  item
	   to add the driver into the system. 

	d. When the driver is added, the screen "Enter the configuration
	   of METF 10/100TX PCI Adapter MDI Driver"  will  be  shown,
	   then please select "OK" item to finish this selection  if you
	   do not make any change for the "Advanced options... ]". 
	
	e. When the driver is selected correctly, the "Add protocol" will
	   be shown,  then select the item  "- SCO TCP/IP" as the default
	   protocol stack. 

	f. After finished the "TCP/IP" protocol  sub-selection,  then the
	   success message is shown as following: 

	   "The following products were sucessfully configured into
		    the system:
	    SCO TCP/IP
	    METF 10/100TX PCI Adapter MDI Driver"
					     
	g. When the adapter has been configured, select 'q' from the
	   netconfig menu, and relink the kernel at the prompt.

4. To active the adapter, you must reboot. When the system
   boots, you should see the following message among the
   other configuration messages:

   %metf0  0xE400-0xE480   11   12   speed=100Mbs id=[xx-xx-xx-xx-xx-xx]

   with the appropriate I/O addresses, IRQ, PCI device number, Adapter
   Type with the chip type and the six octets of the adapter IEEE MAC
   address.

5. If you encounter any problems during installation, (i.e., an error
   message appears on screen) call your dealer for assistance.

Notes: 1. This driver supports up to maximum 4 boards.
       2. Device name is metf0, metf1, metf2, metf3.


C. Trademarks.
--------------
All trademarks or brand names mentioned are properties
of their respective companies.

===End of File===