================================================================================
Funkwerk Enterprise Communications GmbH 05.10.2006
www.funkwerk-ec.com Release Notes V6.08
Firmware ACE for artem ComPoint, artem Wx000, and funkwerk Wx002
================================================================================
This firmware version V6.08 is a minor release.
The firmware supports the funkwerk dual-band enterprise products:
funkwerk W1002, funkwerk W2002,
the artem dual-band enterprise products:
artem W1000, artem W2000, artem W3000, artem W6000T,
the ComPoint enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, artem firmware package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are downgrading to a firmware version older than V5.04,
the configuration will be reset to its default values.
With the ComPoint Manager (CPM) you may save the current
configuration before upgrading.
If you are upgrading from firmware version V4.20 or V4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version V4.20 or V4.22,
then you will have to enable WEP encryption again.
Changes and improvements
none
Bugfixes
Wireless
- [Fw607001]:
Incorrect internal channel table prevented 5 GHz outdoor
operation in Austria.
General
- [Fw607002]: (Wx002 products only)
Incorrect PCI initialization caused some devices to crash on startup.
Restrictions and known problems
Wireless
- Due to 5 GHz dynamic frequency selection (DFS) requirements, a
ComPoint with multi-point bridging (multiple links on one radio
module) must have a numerically higher address (MAC address of
bridging radio module) than any connected link partner.
- Depending on available memory, no more than about 20 service sets
per ComPoint can be utilized.
- When first setting up a bridge link, and then changing the band,
the bridge link will no longer work until the ComPoint is restarted.
- With Windows CE 4.2 client and WPA privacy, reassociation (roaming)
doesn’t work. Instead, after some retries, the client falls back
to standard association, causing a significant period
of connection loss.
--------------------------------------------------------------------------------
If you encounter any problems when installing or using this
product, or would like information about our other
artem products, please don't hesitate to contact us.
* E-Mail (Hotline): hotline@funkwerk-ec.com
* E-Mail (Service): info@funkwerk-ec.com
* Phone (Service): +49-180-300 91 91-0
* Phone (Hotline): +49-180 300 91 91-550
================================================================================
Funkwerk Enterprise Communications GmbH 20.09.2006
www.funkwerk-ec.com Release Notes V6.07
Firmware ACE for artem ComPoint, artem Wx000, and funkwerk Wx002
================================================================================
This firmware version V6.07 is a minor release.
The firmware supports the funkwerk dual-band enterprise products:
funkwerk W1002, funkwerk W2002,
the artem dual-band enterprise products:
artem W1000, artem W2000, artem W3000, artem W6000T,
the ComPoint enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, artem firmware package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are downgrading to a firmware version older than V5.04,
the configuration will be reset to its default values.
With the ComPoint Manager (CPM) you may save the current
configuration before upgrading.
If you are upgrading from firmware version V4.20 or V4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version V4.20 or V4.22,
then you will have to enable WEP encryption again.
Changes and improvements
General
- Hardware support for alternative flash chipset in Wx002
products added.
Bugfixes
none
Restrictions and known problems
Wireless
- Due to 5 GHz dynamic frequency selection (DFS) requirements, a
ComPoint with multi-point bridging (multiple links on one radio
module) must have a numerically higher address (MAC address of
bridging radio module) than any connected link partner.
- Depending on available memory, no more than about 20 service sets
per ComPoint can be utilized.
- When first setting up a bridge link, and then changing the band,
the bridge link will no longer work until the ComPoint is restarted.
- With Windows CE 4.2 client and WPA privacy, reassociation (roaming)
doesn’t work. Instead, after some retries, the client falls back
to standard association, causing a significant period
of connection loss.
--------------------------------------------------------------------------------
If you encounter any problems when installing or using this
product, or would like information about our other
artem products, please don't hesitate to contact us.
* E-Mail (Hotline): hotline@funkwerk-ec.com
* E-Mail (Service): info@funkwerk-ec.com
* Phone (Service): +49-180-300 91 91-0
* Phone (Hotline): +49-180 300 91 91-550
================================================================================
Funkwerk Enterprise Communications GmbH 18.09.2006
www.funkwerk-ec.com Release Notes V6.06
Firmware ACE for artem ComPoint, artem Wx000, and funkwerk Wx002
================================================================================
This firmware version V6.06 is a minor release.
The firmware supports the funkwerk dual-band enterprise products:
funkwerk W1002, funkwerk W2002,
the artem dual-band enterprise products:
artem W1000, artem W2000, artem W3000, artem W6000T,
the ComPoint enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, artem firmware package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are downgrading to a firmware version older than V5.04,
the configuration will be reset to its default values.
With the ComPoint Manager (CPM) you may save the current
configuration before upgrading.
If you are upgrading from firmware version V4.20 or V4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version V4.20 or V4.22,
then you will have to enable WEP encryption again.
Changes and improvements
none
Bugfixes
Wireless
- [Fw605001]:
Internal radio restart sometimes caused ComPoint to crash.
- [Fw605002]:
Under certain circumstances AES or TKIP encryption did not work on
a wireless bridge link if connection was set to locked.
- [Fw605003]:
Association (not re-association) of wireless client failed to
update the learn tables of switches within the same LAN.
Restrictions and known problems
Wireless
- Due to 5 GHz dynamic frequency selection (DFS) requirements, a
ComPoint with multi-point bridging (multiple links on one radio
module) must have a numerically higher address (MAC address of
bridging radio module) than any connected link partner.
- Depending on available memory, no more than about 20 service sets
per ComPoint can be utilized.
- When first setting up a bridge link, and then changing the band,
the bridge link will no longer work until the ComPoint is restarted.
- With Windows CE 4.2 client and WPA privacy, reassociation (roaming)
doesn’t work. Instead, after some retries, the client falls back
to standard association, causing a significant period
of connection loss.
--------------------------------------------------------------------------------
If you encounter any problems when installing or using this
product, or would like information about our other
artem products, please don't hesitate to contact us.
* E-Mail (Hotline): hotline@funkwerk-ec.com
* E-Mail (Service): info@funkwerk-ec.com
* Phone (Service): +49-180-300 91 91-0
* Phone (Hotline): +49-180 300 91 91-550
================================================================================
Funkwerk Enterprise Communications GmbH 10.07.2006
www.funkwerk-ec.com Release Notes V6.05
Firmware ACE for artem ComPoint, artem Wx000, and funkwerk Wx002
================================================================================
This firmware version V6.05 is a minor release.
The firmware supports the funkwerk dual-band enterprise products:
funkwerk W1002, funkwerk W2002,
the artem dual-band enterprise products:
artem W1000, artem W2000, artem W3000, artem W6000T,
the ComPoint enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, artem firmware package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are downgrading to a firmware version older than V5.04,
the configuration will be reset to its default values.
With the ComPoint Manager (CPM) you may save the current
configuration before upgrading.
If you are upgrading from firmware version V4.20 or V4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version V4.20 or V4.22,
then you will have to enable WEP encryption again.
Changes and improvements
none
Bugfixes
Security
- [Fw604001]:
With WPA enabled, a wireless client association could sometimes
fail under certain circumstances.
Restrictions and known problems
Wireless
- Due to 5 GHz dynamic frequency selection (DFS) requirements, a
ComPoint with multi-point bridging (multiple links on one radio
module) must have a numerically higher address (MAC address of
bridging radio module) than any connected link partner.
- Depending on available memory, no more than about 20 service sets
per ComPoint can be utilized.
- When first setting up a bridge link, and then changing the band,
the bridge link will no longer work until the ComPoint is restarted.
- With Windows CE 4.2 client and WPA privacy, reassociation (roaming)
doesn’t work. Instead, after some retries, the client falls back
to standard association, causing a significant period
of connection loss.
--------------------------------------------------------------------------------
If you encounter any problems when installing or using this
product, or would like information about our other
artem products, please don't hesitate to contact us.
* E-Mail (Hotline): hotline@funkwerk-ec.com
* E-Mail (Service): info@funkwerk-ec.com
* Phone (Service): +49-180-300 91 91-0
* Phone (Hotline): +49-180 300 91 91-550
================================================================================
Funkwerk Enterprise Communications GmbH 07.07.2006
www.funkwerk-ec.com Release Notes V6.04
Firmware ACE for artem ComPoint, artem Wx000, and funkwerk Wx002
================================================================================
This firmware version V6.04 is a minor release.
The firmware supports the funkwerk dual-band enterprise products:
funkwerk W1002, funkwerk W2002,
the artem dual-band enterprise products:
artem W1000, artem W2000, artem W3000, artem W6000T,
the ComPoint enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, artem firmware package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are downgrading to a firmware version older than V5.04,
the configuration will be reset to its default values.
With the ComPoint Manager (CPM) you may save the current
configuration before upgrading.
If you are upgrading from firmware version V4.20 or V4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version V4.20 or V4.22,
then you will have to enable WEP encryption again.
Changes and improvements
SNMP
- Translating enterprise specific SNMPv1 notification parameters
according to RFC2576. Updated the release notes file
SNMP/SNMPv1-traps.txt accordingly.
- Replace an unspecified SNMPv1 agent IP address of 0.0.0.0 with
the IP address of the primary interface if sending SNMPv1 traps.
A specific SNMPv1 agent IP address may be entered in the UI menu
"Control/SNMP/Traps" as before.
Bugfixes
Wireless
- [Fw603001]:
Multi-Point bridge links didn't work.
Security
- [Fw603003]:
WPA encryption problems in ACE version V6.02 and V6.03 caused
communication losses with various wireless clients.
SSH
- [Fw603002]:
Enabling SSH the first time could fail.
Restrictions and known problems
Wireless
- Due to 5 GHz dynamic frequency selection (DFS) requirements, a
ComPoint with multi-point bridging (multiple links on one radio
module) must have a numerically higher address (MAC address of
bridging radio module) than any connected link partner.
- Depending on available memory, no more than about 20 service sets
per ComPoint can be utilized.
- When first setting up a bridge link, and then changing the band,
the bridge link will no longer work until the ComPoint is restarted.
- With Windows CE 4.2 client and WPA privacy, reassociation (roaming)
doesn’t work. Instead, after some retries, the client falls back
to standard association, causing a significant period
of connection loss.
--------------------------------------------------------------------------------
If you encounter any problems when installing or using this
product, or would like information about our other
artem products, please don't hesitate to contact us.
* E-Mail (Hotline): hotline@funkwerk-ec.com
* E-Mail (Service): info@funkwerk-ec.com
* Phone (Service): +49-180-300 91 91-0
* Phone (Hotline): +49-180 300 91 91-550
================================================================================
Funkwerk Enterprise Communications GmbH 09.06.2006
www.funkwerk-ec.com Release Notes V6.03
Firmware ACE for artem ComPoint, artem Wx000, and funkwerk Wx002
================================================================================
This firmware version V6.03 is a minor release.
The firmware supports the funkwerk dual-band enterprise products:
funkwerk W1002, funkwerk W2002,
the artem dual-band enterprise products:
artem W1000, artem W2000, artem W3000, artem W6000T,
the ComPoint enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, artem firmware package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are downgrading to a firmware version older than V5.04,
the configuration will be reset to its default values.
With the ComPoint Manager (CPM) you may save the current
configuration before upgrading.
If you are upgrading from firmware version V4.20 or V4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version V4.20 or V4.22,
then you will have to enable WEP encryption again.
Changes and improvements
SNMP
- The UI now only shows the relevant USM user security menu entries
depending on the security level specified.
- Defined and implemented SNMPv1 specific trap numbers
to identify SNMPv1 enterprise traps by an unique number.
All supported enterprise numbers are summarized
in file SNMP/SNMPv1-traps.txt.
With SNMPv2/v3 traps such specific numbers are no longer needed.
Bugfixes
SNMP
- [Fw602001]:
It was allowed by mistake to save inconsistent USM user security
parameters. As a result either the ComPoint crashed immediately or
the USM user entries could have wrong values after reboot.
Restrictions and known problems
Wireless
- Depending on available memory, no more than about 20 service sets
per ComPoint can be utilized.
- When first setting up a bridge link, and then changing the band,
the bridge link will no longer work until the ComPoint is restarted.
- With Windows CE 4.2 client and WPA privacy, reassociation (roaming)
doesn’t work. Instead, after some retries, the client falls back
to standard association, causing a significant period
of connection loss.
--------------------------------------------------------------------------------
If you encounter any problems when installing or using this
product, or would like information about our other
artem products, please don't hesitate to contact us.
* E-Mail (Hotline): hotline@funkwerk-ec.com
* E-Mail (Service): info@funkwerk-ec.com
* Phone (Service): +49-180-300 91 91-0
* Phone (Hotline): +49-180 300 91 91-550
================================================================================
Funkwerk Enterprise Communications GmbH 02.06.2006
www.funkwerk-ec.com Release Notes V6.02
Firmware ACE for artem ComPoint, artem Wx000, and funkwerk Wx002
================================================================================
This firmware version V6.02 is a minor release.
The firmware supports the funkwerk dual-band enterprise products:
funkwerk W1002, funkwerk W2002,
the artem dual-band enterprise products:
artem W1000, artem W2000, artem W3000, artem W6000T,
the ComPoint enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, artem firmware package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are downgrading to a firmware version older than V5.04,
the configuration will be reset to its default values.
With the ComPoint Manager (CPM) you may save the current
configuration before upgrading.
If you are upgrading from firmware version V4.20 or V4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version V4.20 or V4.22,
then you will have to enable WEP encryption again.
Changes and improvements
none
Bugfixes
Wireless
- [Fw601001]:
Bridge remote configuration required restart of remote ComPoint
if a valid different partner MAC address had been configured in
remote ComPoint, and remote ComPoint had had bridge link set to
"enabled".
Restrictions and known problems
Wireless
- Depending on available memory, no more than about 20 service sets
per ComPoint can be utilized.
- When first setting up a bridge link, and then changing the band,
the bridge link will no longer work until the ComPoint is restarted.
- With Windows CE 4.2 client and WPA privacy, reassociation (roaming)
doesn’t work. Instead, after some retries, the client falls back
to standard association, causing a significant period
of connection loss.
--------------------------------------------------------------------------------
If you encounter any problems when installing or using this
product, or would like information about our other
artem products, please don't hesitate to contact us.
* E-Mail (Hotline): hotline@funkwerk-ec.com
* E-Mail (Service): info@funkwerk-ec.com
* Phone (Service): +49-180-300 91 91-0
* Phone (Hotline): +49-180 300 91 91-550
================================================================================
Funkwerk Enterprise Communications GmbH 24.05.2006
www.funkwerk-ec.com Release Notes V6.01
Firmware ACE for artem ComPoint, artem Wx000, and funkwerk Wx002
================================================================================
This firmware version V6.01 is a minor release.
The firmware supports the funkwerk dual-band enterprise products:
funkwerk W1002, funkwerk W2002,
the artem dual-band enterprise products:
artem W1000, artem W2000, artem W3000, artem W6000T,
the ComPoint enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, artem firmware package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are downgrading to a firmware version older than V5.04,
the configuration will be reset to its default values.
With the ComPoint Manager (CPM) you may save the current
configuration before upgrading.
If you are upgrading from firmware version V4.20 or V4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version V4.20 or V4.22,
then you will have to enable WEP encryption again.
Changes and improvements
none
Bugfixes
Security
- [Fw600001]:
UI authentication cache displayed "unknown" or invalid values
in the "Access" and "Auth source" column of EAPOL cache entries.
- [Fw600002]:
Wireless clients requesting WPA_CIPHERSUITE_NONE were not rejected
properly, causing ComPoint to crash.
- [Fw600003]:
Wireless clients from "Symbol" could not associate due to incorrectly
set "install" bit in GTK1-EAPOL-KEY frame.
Restrictions and known problems
Wireless
- Depending on available memory, no more than about 20 service sets
per ComPoint can be utilized.
- When first setting up a bridge link, and then changing the band,
the bridge link will no longer work until the ComPoint is restarted.
- With Windows CE 4.2 client and WPA privacy, reassociation (roaming)
doesn’t work. Instead, after some retries, the client falls back
to standard association, causing a significant period
of connection loss.
--------------------------------------------------------------------------------
If you encounter any problems when installing or using this
product, or would like information about our other
artem products, please don't hesitate to contact us.
* E-Mail (Hotline): hotline@funkwerk-ec.com
* E-Mail (Service): info@funkwerk-ec.com
* Phone (Service): +49-180-300 91 91-0
* Phone (Hotline): +49-180 300 91 91-550
================================================================================
Funkwerk Enterprise Communications GmbH 11.05.2006
www.funkwerk-ec.com Release Notes V6.00
Firmware ACE for artem ComPoint, artem Wx000, and funkwerk Wx002
================================================================================
This firmware version V6.00 is a major release.
The firmware supports the funkwerk dual-band enterprise products:
funkwerk W1002, funkwerk W2002,
the artem dual-band enterprise products:
artem W1000, artem W2000, artem W3000, artem W6000T,
the ComPoint enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, artem firmware package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are downgrading to a firmware version older than V5.04,
the configuration will be reset to its default values.
With the ComPoint Manager (CPM) you may save the current
configuration before upgrading.
If you are upgrading from firmware version V4.20 or V4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version V4.20 or V4.22,
then you will have to enable WEP encryption again.
Changes and improvements
General
- Support for the funkwerk dual-band enterprise products
W1002 and W2002 added.
- Updated syslog client implementation to meet
RFC 3164 - The BSD Syslog Protocol.
Now the "PRI Part" is always included, the "Header Part"
always omitted. The "Message Part" no longer includes the
priority string tag.
Wireless
- Now AP supports distinct MAC addresses, beacons, and information
elements per service set. This feature solves two issues from the
"Restrictions and known problems" section of V5.11:
- With an Agere-based client card (Hermes-1/2 chipset),
it was not possible to associate to a non-WPA service set
on an AP which had other service sets with WPA enabled.
- If more than one service set was configured for a radio, those
service sets were not always shown up in Windows XP's
wireless network list.
- Radio is completely disabled if all service sets of an AP
are disabled.
- Disabled traffic-dependent 5 GHz channel availability check
after 12 hours. The forced check after 24 hours is still
active (as required by EN301893).
- Disabled unnecessary 5 GHz radar detection on bridge slaves.
- All 802.11 authentication and association attempts are now
rejected if bridge is "locked".
- Transmitting the SSID in beacons is now always hidden
if no service sets are defined (e.g. locked bridge links).
Security
- For WPA2 privacy, AES-CCMP group keys are used if "WPA2_only"
operation is selected. With WPA2/WPA mixed mode and "WPA only",
TKIP group keys are used as before.
- Adjusted EAPOL-key retransmit timeout according to IEEE802.11i.
- WEP privacy: added optional shared key authentication according
to IEEE802.11.
- RADIUS attribute "Called-Station-Id" now has SSID appended,
as defined in RFC3580.
- Adjusted contents of "Connect-Info" RADIUS attribute according
to RFC3580.
SNMP
- IEEE802dot11-MIB: Support for several dot11RSNA** statistics
variables added.
- ARTEM-COMPOINT-WLAN-MIB: Changed MAX-ACCESS for SNMP variable
"artemRadioWwrMode" from "read-write" to "read-only".
DHCP
- Ignore illegal options in ACK, NAK, and OFFER replies
from DHCP servers that do not meet the standard.
UI
- SNTP: current date and current time is now manually settable.
- RADIUS accounting: communication with RADIUS server now uses
the new menu entry "Acct secret" for accounting and the menu
entry "Auth secret" for authentication.
Note: after upgrading from previous versions, users are required
to enter the correct "Acct secret" in order to use accounting!
- Wireless extensions: added new submenu "MAC settings" to
Config/Ports/wl_***/Extended menu, with the following configurable
items: Beacon Period, Long Retries, Short Retries,
Tx LifeTime, Rx LifeTime.
- Now SSH and SecWeb (HTTPS) are disabled per configuration default.
Bugfixes
General
- [Fw511007]:
Power loss during system startup could cause a configuration reset.
- [Fw515003]: (802.11g ComPoints on HW version 7.0 only)
With firmware versions >= V5.11 it was not possible to downgrade
to firmware versions V4.x.
- [Fw518001]:
A potential deadlock situation with syslog messages and SNMP
traps sometimes caused ComPoint to crash.
- [Fw518002]: (not first-generation ComPoint products)
Internal time (uptime) lagged about 20 minutes per day.
- [Fw519002]: (not first-generation ComPoint products)
The ComPoint's time was highly out of sync with the NTP time.
Wireless
- [Fw511002]: (802.11b ComPoints only)
Bridge auto configuration was not possible.
- [Fw511003]:
Beacon rate stayed at minimum (32s) if locked bridge link
was unlocked.
- [Fw513002]:
Beacon period could not be changed.
- [Fw513005]:
Certain combinations of more than two enabled service sets with
different security modes including WPA-PSK, prevent clients from
associating to WPA-PSK service sets.
- [Fw514003]:
Association and reassociation messages were not logged to the
console (and optionally to the syslog daemon) if privacy is "none".
- [Fw515002]: (Wx000 only)
While a configured 5GHz bridge is busy scanning channels to find
partner, the ComPoint of the bridge slave crashed when a firmware
update was attempted.
- [Fw516001]:
Any client with power-save enabled blocked the entire radio,
and no more frames could be transmitted on any service set
until next reboot.
- [Fw517001]:
Sequence numbers were not adjusted for AES encryption, causing
permanent loss of connection after temporary link interruption.
- [Fw517002]:
Switching a bridge link to LOCKED state caused the associatied
radio module to be disabled and no data transfer was possible
in that state.
- [Fw519004]:
Under some circumstances, a 5GHz bridge link was not restored
after band scan was finished.
- [Fw519005]:
Under certain circumstances, wireless card firmware hung,
causing the watchdog to reboot the device.
- [Fw520001]:
Transmission of broadcast/multicast frames to Intel 2200/2915
client in powersave mode was unreliable.
- [Fw520004]:
ComPoint sporadically rebooted under certain WLAN load conditions.
Security
- [Fw511004]:
EAPOL-key frames received with incorrect replay counter caused
a reject of the wireless client. According to IEEE802.11i,
those frames shall be silently ignored.
- [Fw513004]:
EAPOL-START frames from client were not ignored in WPA-PSK mode.
- [Fw515001]:
RADIUS attribute "Acct-Delay-Time" contained wrong values
during authentication.
- [Fw519001]:
With WPA/WPA2 retransmission of EAPOL-key frame #3 didn't work.
- [Fw520003]:
After connecting WPA manager to the ComPoint's WPA Agent,
there was a high probability that the ComPoint crashes everytime
a client associates or disassociates, if both WPA and accounting
are enabled.
DHCP
- [Fw511006]:
Sometimes the DHCP client did not renew the lease
if the lease has been expired.
VLAN
- [Fw511005]:
Wireless repeating on an AP was not possible if VLAN has been enabled.
SNMP
- [Fw511001]:
ARTEM-COMPOINT-WLAN-MIB: reading and writing of OID
artemAPServiceSetAdminStatus didn't work.
- [Fw513001]:
ARTEM-COMPOINT-WLAN-MIB: setting OID artemRadioWwrMode didn't work.
- [Fw513003]:
Changing SNMP configuration parameters caused ComPoint to crash.
- [Fw514002]:
ARTEM-COMPOINT-BLD-MIB: getting OID artemBLDTargetIf displayed
undefined value.
- [Fw519003]:
Q-BRIDGE-MIB: setting OID dot1qPortAcceptableFrameTypes and
OID dot1qPortIngressFiltering didn't work.
- [Fw520002]:
Setting SNMP-V3 USM user authentication and encryption alogorithms
with corresponding passwords was not possible, beacause the menu
entry "Security" wasn't accessible in Telnet/SSH/Web/SecWeb.
The menu entry "Security" was spuriously replaced with the
"Acct secret" entry from EAP.
UI
- [Fw514001]:
Control/Security/Authenticate/EAP/Advanced menu:
Changing the PMK lifetime value failed.
- [Fw515004]:
On successful SSH logins the password unnecessarily was asked
a second time unless a default password was used.
Restrictions and known problems
Wireless
- Depending on available memory, no more than about 20 service sets
per ComPoint can be utilized.
- When first setting up a bridge link, and then changing the band,
the bridge link will no longer work until the ComPoint is restarted.
- With Windows CE 4.2 client and WPA privacy, reassociation (roaming)
doesn’t work. Instead, after some retries, the client falls back
to standard association, causing a significant period
of connection loss.
--------------------------------------------------------------------------------
If you encounter any problems when installing or using this
product, or would like information about our other
artem products, please don't hesitate to contact us.
* E-Mail (Hotline): hotline@funkwerk-ec.com
* E-Mail (Service): info@funkwerk-ec.com
* Phone (Service): +49-180-300 91 91-0
* Phone (Hotline): +49-180 300 91 91-550
================================================================================
Funkwerk Enterprise Communications GmbH 22.08.2005
www.funkwerk-ec.com
Firmware ACE for artem Onair ComPoint / Wx000 Release Notes V5.11
================================================================================
This firmware version V5.11 is a major release.
The firmware supports the artem dual-band enterprise products:
artem W1000, artem W2000, artem W3000,
the ComPoint enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, artem firmware package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are downgrading to a firmware version older than V5.04,
the configuration will be reset to its default values.
With the ComPoint Manager (CPM) you may save the current
configuration before upgrading.
If you are upgrading from firmware version V4.20 or V4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version V4.20 or V4.22,
then you will have to enable WEP encryption again.
Changes and improvements
Security
- Major redesign of WPA2/RSN/IEEE802.11i wireless security engine
significally improves interoperability with various clients
and different supplicants.
- WPA2/RSN preauthentication support added.
- New wireless security mode "WPA-only" added for AccessPoints
to support interoperability with some older wireless clients
having problems to communicate properly if WPA mixed mode
(WPA and WPA2) is used. The user interface has changed accordingly.
- Added support for WPA reauthentication from wireless client.
Wireless
- Channel setting "AUTO_DFS" has been removed for 2.4 GHz bridges since
it caused loss of bridge connectivity after restart of any endpoint.
- Regulatory domain configuration: selecting "anywhere" for "Usage area"
now only enables channels which are allowed for both indoor and
outdoor usage.
- Updated Austria 5GHz channels according to recent regulatory changes.
- Added console message on 5 GHz radar detection.
- Bridge Scan and Setup now have overall timeouts
(currently only configurable via SNMP).
- Improved bridge management, bridge scan and bridge setup
now work faster and more reliable.
Broken Link Detection
- UI: View-only attribute "link port" added, displaying the
local port over that the remote host (BLD's IP address)
was reachable the last time.
- UI: Added "Port table" menu due to UI limitations.
- Changed value range for "Timeout" (1..300) and "Retries" (0.99).
- Support for a router's ICMP_TIMEEXCEEDED reply added.
- Changed the semantics of BLD controlled bridge ports
if the BLD's link status goes down:
A locked bridge link is unlocked
if all of the following conditions are true:
a) the bridge link port is member of the BLD's controlled ports
b) the bridge link port equals the current BLD's link port
c) the bridge link port is locked
d) the bridge link port's operational status is down
BLD controlled bridge ports have no action executed
if the BLD's link status goes up.
Filter
- MAC Filter: Added support for source port specific filtering rules.
SNMP
- Added private MIB ARTEM-COMPOINT-BLD-MIB to configure
Broken Link Detection (BLD).
- Added private MIB ARTEM-COMPOINT-FILTER-MIB to configure
Layer-2 filtering.
- Added private MIB ARTEM-COMPOINT-WLAN-MIB to configure
wireless AccessPoint and wireless Bridge parameters
not covered in standard MIBs.
- Added standard Q-BRIDGE-MIB for static VLAN configuration.
The following MIB objects of the Q-BRIDGE-MIB are supported:
a) dot1qBase (global VLAN information)
b) dot1qPortVlanTable (PVID table)
c) dot1qVlanStaticTable (VLAN table)
- The wireless security parameters for WPA-PSK, WPA-Enterprise,
WPA2-PSK, and WPA2-Enterprise can now be fully configured.
The configuration of the backend authentication servers
(RADIUS) via SNMP is not supported yet.
- Support for the RADIUS-AUTH-CLIENT-MIB added.
UI
- Secure Web server (see Restrictions and known problems of V5.00).
SSL now uses final versions of certificate and private key.
The browser will no longer complain about a certificate signed
by an unknown certificate authority and host name mismatch,
as soon as the certificate (see login page) is installed.
For background information and installation instructions
please refer to the file "readme-certificate.txt"
in folder "SSL-certificate".
- On SSH login the telnet password dialog is replaced with
a "Hit RETURN to continue" message, since the password already
has been entered for SSH login.
- Telnet/SSH: The "Please wait..." output displayed on command
execution at the bottom of the screen has been disabled.
- Configuration upload via ComPoint Manager (CPM) extended to allow
all configurations to become accepted as long as the configuration
version does not exceed the current firmware version.
Bugfixes
Wireless
- [Fw504002]:
After disconnecting an Agere Hermes-1 client, under certain
circumstances the Compoint could crash while removing the client
from its database.
- [Fw503001]:
Bridge links with TKIP or AES encryption in conjunction
with VLAN enabled sometimes caused system to crash.
- [Fw500022]:
With Agere Hermes-2 based clients, WPA association frequently
needed several attempts to succeed.
- [Fw500021]:
Enabling power management on Agere Hermes-2 based client cards
caused data transfer to client to become highly unreliable.
- [Fw500017]:
Reassociation failed to work with WPA2.
- [Fw500016]:
Roaming with Agere Hermes1/2 clients worked very unreliable.
- [Fw500015]: (see Restrictions and known problems of V5.01)
Channel 165 was not supported.
- [Fw500014]: (see Restrictions and known problems of V5.01)
No 5GHz channels were available when country is set to Spain.
- [Fw500013]:
5 GHz radar detection didn't work at all.
- [Fw500012]:
Bridge "link lost" condition was never cleared
with no external data traffic.
- [Fw500011]:
A fixed, slot dependant channel was set even
if DFS_AUTO was selected.
- [Fw500010]:
Bridge channel sometimes changed when adding a new bridge link.
Broken Link Detection
- [Fw502002]:
Incoming ICMP messages which were not related to BLD's functionality
increased the effective test interval period. This could cause BLD
link-up events to be recognized with substantial (worst
case: infinite) delay.
VLAN
- [Fw503002]:
The authentication between wireless clients and the backend
authentication server failed if VLAN enabled and the security mode
of the AccessPoint set to WPA-Enterprise.
- [Fw500018]:
Changing a port's PVID (Port Vlan Identifier) caused the modified
port to get automatically removed from the VLAN member set
corresponding to the original PVID.
- [Fw500008]:
Management of device through non management VLAN was possible.
Filter
- [Fw501001]:
Removing a protocol filter rule did not work.
- [Fw510001]:
The number of protocol filter rules was reset to zero on
firmware upgrade from versions V5.00-V5.03 to V5.04-V5.10.
DHCP
- [Fw500007]:
If a DHCP server does not send renewing and rebinding timer values
the DHCP client permanently tried to renew the lease.
SNMP
- [Fw502001]:
Setting the Privacy from none to WEP (dot11PrivacyInvoked OID)
did not work.
- [Fw501002]:
Setting a host mask for a community was not possible.
UI
- [Fw504003]:
The SSL certificate's serial number was not unique. Some Web browsers
(e.g. Firefox) generated warnings if sessions with different ComPoints
were opened.
- [Fw504001]:
Loading a foreign configuration (copied from a different ComPoint)
caused the secure user interface services (Secure Web, SSH) to
become inaccessible.
- [Fw500020]:
Incorrect instance count caused "Add SSID" for AccessPoints
and "Add Link" for Bridges to be selectable even if all possible
instances already were in use.
- [Fw500019]:
With more than 10 service sets configured for one radio,
ComPoint crashed when trying to configure any service set.
- [Fw500009]: (see Restrictions and known problems of V5.01)
Issueing a time-consuming command sometimes caused the current
Telnet/SSH session to be closed by the device.
Restrictions and known problems
Wireless
- With an Agere-based client card (Hermes-1/2 chipset),
it is not possible to associate to a non-WPA service set
on an AP which has other service sets with WPA enabled.
- Depending on available memory, no more than about 20 service sets
per ComPoint can be utilized.
- When first setting up a bridge link, and then changing the band,
the bridge link will no longer work until the ComPoint is restarted.
- With Windows CE 4.2 client and WPA privacy, reassociation (roaming)
doesn’t work. Instead, after some retries, the client falls back
to standard association, causing a significant period
of connection loss.
- If more than one service set is configured for a radio, those
service sets will not always show up in Windows XP's wireless
network list. In order to join one of those service sets,
manual configuration has to be used.
--------------------------------------------------------------------------------
If you encounter any problems when installing or using this
product, or would like information about our other
artem products, please don't hesitate to contact us.
* E-Mail (Hotline): hotline@funkwerk-ec.com
* E-Mail (Service): info@funkwerk-ec.com
* Phone (Service): +49-180-300 91 91-0
* Phone (Hotline): +49-180 300 91 91-550
================================================================================
Release Notes V5.01 20.04.2005
Firmware artem ACE Funkwerk Enterprise Communications GmbH
www.funkwerk-ec.com
This Firmware Version 5.01 is a minor release.
The firmware supports the artem dual-band enterprise products:
artem W1000, artem W2000, artem W3000,
the ComPoint enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
Wireless
- Updated list of allowed 2.4GHz channels for France - according to
recent regulatory changes, now all channels 1..13 are allowed.
- Improved UI menu entry of "RF settings/Tx power".
Now power can be selected from list (as before),
or entered directly, e.g. "13mW" or "6dBm".
For directly entered values, the used value may differ
from the entered one due to rounding effects.
DHCP
- Now a configured DHCP client identifier is sent with DHCP requests.
But: changing the client ID only takes effect after rebooting the device.
UI
- SSH: now the required RSA and DSA keys are product specific.
If SSH is enabled, then both keys are generated automatically after
configuration reset or uploading a configuration from another device.
Computing the keys may take up to two minutes, depending on the hardware.
Bugfixes
Security
- [Fw500005]:
In a configuration with different WPA authentication modes in different service sets,
association to some service sets was not possible.
- [Fw500006]:
Access point WPA interoperation with Symbol client cards was not possible.
ACL
- [Fw500004]:
If AclRemote was enabled, then the device hung after restart.
UI
- [Fw500001]: (see Restrictions and known problems of V5.00)
Telnet server: The telnet service could not be disabled
in the Control/Security/UI control menu. Now it can.
But at least one of the interactive UI services
(telnet/SSH/Web/SecWeb) must always be enabled.
- [Fw500002]: (see Restrictions and known problems of V5.00)
The password prompt as well as the topmost line
of every Telnet/SSH screen could be displayed misprinted,
depending on the Telnet/SSH client.
Restrictions and known problems
UI
- Secure Web server: The used certificate and private key are preliminary.
Currently, opening a secure Web connection causes the browser to warn
about unknown RootCA and host name mismatch. These warnings can be safely ignored.
- Issueing a time-consuming command sometimes causes
the current Telnet/SSH session to be closed by the device.
The offending command is always executed properly and you can immediately
continue working by opening a new session.
Wireless
- With an Agere-based client card (Hermes-1/2 chipset), it is not possible to associate
to a non-WPA service set on an AP which has other service sets with WPA enabled.
- Dependent on available memory, it is possible that the limit of 16 service sets
per radio module cannot be fully utilized.
- Channel 165 is not supported (only relevant for 5GHz operation in certain non-European countries).
- When first setting up a bridge link, and then changing the band,
the bridge link will no longer work until the ComPoint is restarted.
- No 5GHz channels are available when country is set to Spain.
--------------------------------------------------------------------------------
Release Notes V5.00 07.03.2005
Firmware artem ACE Funkwerk Enterprise Communications GmbH
www.funkwerk-ec.com
This Firmware Version 5.00 is a major release.
The firmware supports the artem dual-band enterprise products:
artem W1000, artem W2000, artem W3000,
the ComPoint enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
General
- Support for the new products "artem W1000/W2000/W3000" added.
- Simple Network Time Protocol (SNTP) client added (UI: Control/SNTP).
- Syslog client added (UI: Control/Logging).
- New SNMP agent integrated with full support of versions 1, 2, 3,
the USM user model as well as VACM views.
- Status LEDs for AP, BR, and BR2 mode are now turned off if port is
closed or failed to open.
Wireless
- Added SNMP support for the IEEE802dot11 MIB.
- Added multiple Service Set support.
Via the menu "Config/Ports/wlX_ap/Service sets" it is possible to add,
remove and modify so called "Service Sets". A Service Set is a virtual
Access Point which clients can associate to and exchange data with in
the usual manner.
For each radio module, up to 16 service sets can be created.
The menu item "Add SSID" automatically disappears if no more
service sets can be added.
The last service set cannot be removed, therefore always at least
one service set per radio module must be present.
The RF settings (e.g. channel) affects each service set attached
to the radio module.
The "Network name" (aka SSID) can be selected independently for each service set.
The privacy settings can be selected independently for each service set.
Additional independent settings for each service set include
VLAN, BLD und filtering.
Wireless visibility ("Bcst SSID") can be configured individually for each service set.
However, no SSID is broadcasted in the 802.11 beacons if there is more than one
active service set. The service sets with visibility enabled "Bcst SSID = enabled"
do reply to 802.11 probe requests with SSID = "ANY" and are therefore openly visible.
For channel selection (Config/Ports/wlX_ap/RF_settings/channel), there is a new value
"Auto DFS". When "Auto DFS" is selected, the AP automatically scans the band on
initialization and selects one of the channels with least activity.
- Removed problems with high ping latency, and very low data transfer
rates over cascaded AP/Bridges.
- Regulatory Information for the 4.9-5.9 GHz Band updated.
- Now the regulatory domain configurations are placed in a separate
sub menu in Config/System.
- The selectable regulatory domain countries depend on
the supported certificates flashed into the wireless cards.
- Added a view of the complete list of supported regulatory domain countries.
- Enabled link finder (automatic master/slave DFS channel adaption)
for 5GHz bridge links.
Security
- Added accounting support according to RFC2866.
The accounting menu is active only if WPA is enabled.
The accounting information is sent to the server specified as authentication server.
No client can associate if accounting is enabled and the accounting server is unreachable.
- The real user name is also transmitted to the accounting server (Radius)
if accounting is enabled. In WPA PSK mode the client's MAC address will be
transmitted in the Radius user name attribute.
- The menu items "Reauth switch" and "Reauth period" in Control/Security/Authenticate/EAP/Advanced
control broadcast key roll-over if WPA is enabled. In pure IEEE802.1x mode (WPA disabled)
full reauthentication is utilized.
- WPA: added optional AES-CCMP encryption for pairwise keys. For group keys the strongest security is TKIP.
- Added WPA2 support and mixed operation of WPA2- and WPA-capable clients.
- WPA mixed mode now also runs with Microsoft SP1 and SP2 clients.
Microsoft currently doesn't support WPA2 but offers AES-CCMP for
pairwise keys which is not a valid Wi-Fi combination.
So the pairwise cipher suite is forced to TKIP if AES-CCMP
is selected in Microsoft supplicants.
Filtering
- Changed the semantics of the "WL admin" feature accessible
in the Config/Security menu. Now only access point ports
are excluded from the set of ports over which communication
is allowed with the local IP stack.
UI
- Secure Web server (HTTPS/SSL) added.
"UI control" menu added to Control/Security
to enable/disable Web (HTTP) and Secure Web (HTTPS/TLS).
- SSH daemon added to support secure telnet user interface.
Menu entry added to Control/Security/UI control to enable/disable SSH,
and to enable/disable Telnet.
- WPA agent added for monitoring WPA state transitions and diagnostics
via a special tool. This service is disabled by default and may be
activated in the Control/Security/UI control menu.
- Added two menu entries in Config/System to switch regulatory domain via
User Interface (Has been available in some develeoper versions before).
- Added new menu item for EAP server configuration in Port
security menu (only if WPA-TLS selected).
- Moved menu item "Antenna Div" from "Extended" to "RF settings".
- Added new menu item "RF settings/sel. channel" to show the currently
selected channel if auto-channel (DFS) is selected.
- SSID is displayed as "***" for non-admin, instead of empty field.
- Added "Radio band" menu entry to Bridge "Auto_config/Settings" menu.
- Renamed entry in "Security" menu from "Enable state" to "State".
- Added new "Accounting" menu entry in Ports/xxx/Security
menu (currently only available for WPA-802.1x).
- Changed display of values for "Mcast rate", e.g. from "1" to "1_Mbps".
- Menu item "Link Test" for BR/BR2 is no longer available
if "Link state" is "disabled".
- On 5GHz radio band, 802.11b rates (1,2,5.5,11 mbps) are suppressed
in "Status/Ports" node table / status display.
- Added automatic scrolling for menus with > 9 entries (Telnet only!).
- Changed automatically generated AP port name from "wl1_ap1"
to "wl1_ap01".
- Added new menu entry "Config/Ports/wp_xx_ap/Extended/Direct link".
- Added new "PHY settings" menu with
entries "ACK window", "ED threshold", "CCA mode", "CW min", "CW max".
- Menu selection Control/Security/Authentication/IEEE802.1x is
hidden for ports where WPA-PSK or WPA-TLS is selected.
- Re-structured and renamed some VLAN submenus and commands.
- Changed menu WPA-I802.1x to WPA-Server.
- Renamed "DS channel" menu item to "Channel".
- Transmit power menu now shows "max" for maximum power,
and exact dBm values for less power.
- Added "PHY settings" submenu from "RF settings" to "Extended".
- Moved Nitro-XM specific settings to new submenu "Extended/Nitro XM".
- Changed Nitro-XM defaults to Frame compression=off, Direct Link=On.
- Added new menu entry "Mixed mode" for WPA2/WPA mixed mode.
- Renamed menu entry "Auth method" to "Privacy".
- Renamed menu entry "WPA-PSK" to "WPA2-PSK".
- Renamed menu entry "WPA-Server" to "WPA2 Enterpr.".
- Presentation of the routing table improved.
- Presentation of the ARP cache changed.
- Extended help texts for Config/Ports/w-*_ap**/Extended/"Mode 802.11g".
- WEB UI: value input fields are now automatically activated - no
more mouse clicks in input field are necessary.
- Config/"Reset to FD" entry added to completly reset the product
to the factory default values.
- Needless auto-refresh property of some table views removed.
Bugfixes
Wireless
- [Fw479001]:
Wireless clients were unable to associate without security (WPA/RSN) enabled.
- [Fw463002]: (802.11b ComPoint products only)
Added periodic (60min) Agere radio card restart when no client is associated.
This should fix the problem of some customers that no client is able to associate,
while the card firmware still is operative.
- [Fw463001]: (first-generation ComPoint products only)
ComPoint crashed if any client tries to connect with
"IEEE802.1x" authentication enabled (not WPA).
- [Fw460002]:
When CP was powered up with WPA security, and was
switched to WEP later, then WEP keys were not set correctly.
Broken Link Detection
- [Fw483001]:
The reception of an invalid or unexpected ICMP_DESTUNREACH frame
also caused a BLD link-down event. That could be logically wrong.
SNMP
- [Fw478005]:
Missed support for "dot11RSNAConfigPSKPassPhrase" added.
- [Fw478004]:
Invalid True/False values for variables of type "TruthValue" corrected.
UI
- [Fw478002]:
MAC filtering: re-setting of a new active rule was needless
and wrong, if the last port was removed from a rule.
- [Fw478003]:
In Web UI, values "100BaseTX_HD" and "100BaseTX_FD"
couldn't be selected for ethernet connection.
Restrictions and known problems
UI
- Secure Web server: The used certificate and private key is preliminary.
Currently, opening a secure Web connection causes the browser to warn
about unknown RootCA and host name mismatch. These warnings can be safely ignored.
- Telnet server: The telnet service cannot be disabled
in the Control/Security/UI control menu.
- Issueing a time-consuming command sometimes causes
the current Telnet/SSH session to be closed by the device.
The offending command is always executed properly and you can immediately
continue working by opening a new session.
- The password prompt as well as the topmost line of every Telnet/SSH screen
may be displayed misprinted, depending on the Telnet/SSH client.
Wireless
- With an Agere-based client card (Hermes-1/2 chipset), it is not possible to associate
to a non-WPA service set on an AP which has other service sets with WPA enabled.
- Dependent on available memory, it is possible that the limit of 16 service sets
per radio module cannot be fully utilized.
- Channel 165 is not supported (only relevant for 5GHz operation in certain non-European countries).
- When first setting up a bridge link, and then changing the band,
the bridge link will no longer work until the ComPoint is restarted.
- No 5GHz channels are available when country is set to Spain.
-----------------------------------------------------------------------------------------
Release Notes 4.64 28.02.2005
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.64 is a minor release.
The firmware supports the ComPoint Enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Bugfixes
Wireless Security
- [Fw463001]: (first-generation ComPoint products only)
ComPoint crashed if any client tries to associate
with "IEEE802.1x" authentication (not WPA) enabled.
Wireless
- [Fw463002]: (802.11b based ComPoint products only)
Some customers had the problem that no client is able to associate
after some time of operation, while the card firmware still is operative.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.63 28.12.2004
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.63 is a minor release.
The firmware supports the ComPoint Enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Bugfixes
Wireless
- [Fw462001]: (CPS-BR-* and CPE-BR1-* products only)
The default operating mode for the wireless port
was AP instead of BR.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.62 20.12.2004
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.62 is a minor release.
The firmware supports the ComPoint Enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
General (CPE-XT1-* products only)
- The wireless port now can be switched between AP and Bridge mode.
Note: downgrading to a firmware version <= V4.61 with default settings
starts the ComPoint's wireless port in Bridge mode.
Bugfixes
Ethernet
- [Fw460003]:
After setting auto-negotiation to "disabled" and connection
to "10BaseT-HD", ethernet always switched back to "10BaseT-FD"
if auto-negotiation is supported by switch/hub.
- [Fw460004]:
After setting auto-negotiation to "disabled" and connection
to "10BaseT-HD", restart caused connection to operate with
"100BaseTX_??" if auto-negotiation is supported by switch/hub.
- [Fw460005]:
Ether link-up event with 10 Mbps link speed sometimes caused CP to crash.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.61 17.11.2004
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.61 is a minor release.
The firmware supports the ComPoint Enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Bugfixes
Ethernet
- [Fw460001]:
When connected to certain devices with long cables (more than 75 meters),
Ethernet could have very poor performance and high packet loss.
The fix for the "short-cable" bug introduced in firmware version 4.20
erroneously changed the DSP parameters sometimes with long cables, too.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.60 30.09.2004
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.60 is a minor release.
The firmware supports the ComPoint Enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Bugfixes
General
- [Fw459001]: (CPE products only)
At low ambient temperature the firmware failed to start
on some devices.
Wireless
- [Fw459002]:
With WPA, association of client after short out-of-range situation
sometimes failed on first attempt.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.59 09.09.2004
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.59 is a minor release.
The firmware supports the ComPoint Enterprise products:
CPE-XT1-b, CPE-XT2-b, CPE-XT3-b, CPE-BR1-b,
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
General
- New Bootloader and Monitor for alternative hardware support added.
- No functional changes at all.
Bugfixes
none
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.58 24.08.2004
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.58 is a minor release.
The firmware supports the ComPoint Enterprise products:
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
General
- Hardware support for alternative flash chipsets added.
Bugfixes
none
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.57 09.08.2004
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.57 is a minor release.
The firmware supports the ComPoint Enterprise products:
CPE-XT1-g, CPE-XT2-g, CPE-XT3-g, CPE-BR1-g,
the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
General
- Support for the new ComPoint Enterprise products CPE-XXX-g.
Wireless
- Improved IP address recognition of ARtem AccessClient-Products
in the wireless node table.
Bugfixes
General
- [Fw456005]:
Under heavy load conditions it was possible that the watchdog timer
could not be reset and the system rebooted.
Web UI
- [Fw455001]:
Web UI via IE and latest IE service pack was not available
after a successfull login.
- [Fw456001]:
Opera Browser > 7.11 has shown the file download dialog
instead of the submenu of some menu items.
- [Fw456002]:
While changing the password of admin, user or view level
the input of the password has been shown in plain text.
- [Fw456003]:
Menu commands with more than one parameters generated
wrong link URLs after entry of first parameter.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.56 14.04.2004
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.56 is a minor release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
Wireless (802.11b Hermes-2 products only)
- Improvements regarding intra-BSS repeating.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.55 05.04.2004
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.55 is a minor release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
Wireless (802.11g products only)
- WPA: Some minor improvements regarding the Wi-Fi certification.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.53 24.02.2004
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.53 is a minor release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
Wireless (802.11g products only)
- WPA: Increased tolerance with Wi-Fi incompatible
supplicant implementations added.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.52 17.02.2004
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.52 is a minor release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
Wireless
- Upgrade of 802.11b Agere Hermes-2 firmware version to 2.16.
- 802.11g products only:
Increased 802.11g radio long-term stability
by enhanced error recovery mechanism.
Bugfixes
Wireless
- [Fw451001]: (802.11g products only)
Changing settings could cause ComPoint to hang.
- [Fw450001]: (802.11b products only)
IPX 802.2 and 802.3 frames were not handled correctly.
- [Fw449001]:
No association was possible with Buffalo WLI-CB-G54A cards.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.49 27.01.2004
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.49 is a minor release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Bugfixes
Wireless
- [Fw448001]: (802.11b products only)
Under certain circumstances, ARP address resolution failed
between 2 clients on 2 different AP's.
The bugfix [Fw446001] introduced in version 4.48 did not
completely solve the problem.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.48 22.01.2004
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.48 is a major release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
General
- Improved error recovery from firmware malfunctions.
Wireless
- Automatic bridge configuration of 802.11g radio now explicitly
ignores 802.11b partners. Bridge links between 802.11b and
802.11g radios are NOT SUPPORTED (and have never been)!
- Improved WPA interoperability with Agere Hermes-2 based clients.
- Agere radios now silently drop 802.3 frames with inconsistent
length field.
- Accelerated WPA client association.
VLAN
- Initial version of VLAN support. This version contains tagging
and untagging of outgoing/incoming frames and static VLAN configuration
according to 802.1q.
Bugfixes
Wireless
- [Fw446001]: (802.11b products only)
Under certain circumstances, ARP address resolution failed
between 2 clients on 2 different AP's.
- [Fw447003]: Modifications of multicast rate were not retained
across power cycle.
- [Fw444001]: (802.11g products only)
Switching encryption from WPA-* to WEP didn't work correctly,
no data could be transferred until ComPoint restart.
- [Fw444002]: (802.11g products only)
Clients with TI TNET1130 based cards were not able to associate
to 802.11g AP with WPA security.
SNMP
- [Fw447004]: System group sysServices corrected: currently we
are a "wireless" layer 2 bridge and not a router and we do
not offer any layer 7 services.
UI
- [Fw447002]: Changing certain values in the user interface
(values that affect security handling, e.g. ACL, SSID)
sometimes caused ComPoint to hang.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.44 28.11.2003
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.44 is a minor release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
Wireless
- Upgrade of 802.11b Agere Hermes-2 firmware version to 2.00.
UI (802.11g products only)
- Antenna diversity mode can now be changed by new menu entry
"Config/Ports/wl_???/Extended/Ant diversity".
Default value is "none" (no diversity).
Antenna diversity mode should be manually changed (e.g. to "receive")
if two antennas are connected to the same radio.
Bugfixes
Wireless
- [Fw442001]: DoubleBridge erroneously used factory default
channel #6 for both radios.
- [Fw440004]: (802.11g products only)
Setting "DTIM period" to the invalid value "0" caused failure of
wireless card on next restart, requiring a reset to factory default.
- [Fw440005]: (802.11g products only)
Occasional degradation of signal reception was caused by the radio
erroneously switching between MAIN and AUX antenna connector.
This has been fixed by setting the default antenna diversity mode to "none".
If required, the antenna diversity can be changed manually.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.43 25.11.2003
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.43 is a minor release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
Wireless (802.11b products only)
- Upgrade of 802.11b Agere Hermes-2 firmware version to 1.75.
Bugfixes
Wireless (802.11b products only)
- [Fw429006]: (802.11b products only)
Downgrade of 802.11b Agere Hermes-1 firmware version to 8.72
due to long-term stability problems under heavy load with WEP enabled.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.42 21.11.2003
Firmware ARtem Onair ComPoint ARtem GmbH
www.ARtem.de
This Firmware Version 4.42 is a major release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b,
CPS-AP-g, CPS-BR-g, CPD-XT-g, CPD-BR-g,
CPT-XT-b, CPT-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Changes and improvements
Wireless
- Setting a bridge to "Locked" state causes the internally used
administrative AP to be invisible. All association attempts to
the administrative AP are rejected.
- For wireless Bridge/Doublebridge added console log entries to indicate
"loss of connection detected" and "connection restored".
- Upgrade of 802.11b Agere Hermes-1 firmware version to 9.40.
- Upgrade of 802.11b Agere Hermes-2 firmware version to 1.61.
Wireless (802.11g products only)
- Access point now offers WPA security (PSK/TLS/TTLS)
according to Wi-Fi requirements.
- Protected EAP (PEAP) authentication added.
- Major security improvement for wireless Bridge/Doublebridge by use
of TKIP encryption. Keys are generated from WPA-like passphrase.
Each link of Multipoint-bridge has different transient keys, both
radio connections of Doublebridge have different transient keys.
- Changed factory default value for "Mode 802.11g" from "longrange_mixed"
to "mixed" in order to meet Wi-Fi requirements.
UI
- New entry in wireless Bridge/Doublebridge "Security" menu allows
user to enable encryption with automatically generated random WEP keys
or TKIP passphrase. This option is only available if the passphrase
or the WEP transmit key is empty.
- Passphrase in wireless Bridge/Doublebridge "Security" menu
can be cleared with "clear_key" menu selection.
This causes encryption to be disabled.
- In wireless "Security" menu, the "enable" selection of the
"Enable state" entry is suppressed if the passphrase or selected
transmit key is empty.
- In wireless "Security" menu, WEP encryption gets disabled if selected
Tx key is cleared, or if Tx "Key number" is changed to an empty key.
- In wireless Bridge/Doublebridge "Auto config" menu,
"Config state" and "Scan results" entries are suppressed
if "Lock state" is set to "locked".
- Added entries for "Card type" and "Network name" to wireless ports
in Status/Ports menu.
- In wireless Status/Ports menu, new entry "Wireless stat" displays
extensive radio-specific statistical information.
- In Control/SNMP the "SNMP port" is set to read-only.
Bugfixes
Wireless
- [Fw429003]: Fast LED blinking to indicate broken link (BLD)
didn't work correctly for Access Points.
- [Fw405001]: (CPBR-2W11, CPD-BR-b, CPD-BR-g only)
After switching from Doublebridge to Bridge, performing
auto-configuration on the Bridge caused ComPoint to crash.
- [Fw429005]: (802.11g products only)
If WEP is enabled, heavy load conditions could
cause radio to stop functioning.
UI
- [Fw429001]: Telnet didn't handle "%" character correctly.
- [Fw400003]: Fixed problems with Windows XP Telnet echo.
- [Fw429002]: Changing SSID or security settings could cause
802.11g Access Point to hang.
- [Fw439001]: If a ComPoint's node name has more than 20 chars,
it was not possible to select the device in the scan result table
for remote bridge link partners.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
UI
- Under rare conditions, modifications in a UI session (telnet/Web)
may cause ComPoint to crash if additional sessions are open
to the same ComPoint.
-----------------------------------------------------------------------------------------
Release Notes 4.29 09.09.2003
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
This Firmware Version 4.29 is a minor release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b, CPS-AP-g, CPS-BR-g, CPD-AP-g,
CPD-BR-g, CPD-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT NOTICE:
If you are upgrading from firmware version 4.20 or 4.22,
please check the WEP encryption status!
If you had enabled WEP encryption with firmware version 4.20 or 4.22,
then you will have to enable WEP encryption again.
Bugfixes
Wireless
- [Fw428003] Bridge auto-configuration didn't work
with encryption disabled.
- [Fw428002]: (ComPoints with 802.11b cards only)
Under high load and with WEP enabled, certain packet combinations
could cause radio firmware to crash after some time, leading to
loss of radio connection until reboot.
- [Fw422009]: Multi-Point bridge didn't work with any
encryption since firmware version 4.22.
- [Fw420010]: (CPD-*-g products only)
Some 3rd-party wireless client cards transmit empty data
frames under certain conditions. These frames caused the
second radio to fail if WEP is enabled, requiring a reboot.
- [Fw420009]: Entering a wireless network name with exactly 32
characters was truncated to 31 characters.
- [Fw422004]: It was not possible to enter a network name
with embedded spaces.
Mac filter
- [Fw422008]: After the system was restarted a specified filter rule with
source mac address set to "local" was ignored and could not be deleted.
This is also the case if the wireless admin configuration had been switched
to "forbidden".
UI
- [Fw420011]: Menu item "Security" could not be switched to "open/WEP"
via Web frontend. Now this item has been renamed to "WEP".
- [Fw422003]: Because of a design flaw in the new "Security" menu,
it was not possible to setup WEP keys before enabling encryption.
- [Fw422005]: It was not possible to enter a name with
embedded spaces for "Config/System/Node name".
- [Fw422006]: It was not possible to enter a name with
embedded spaces for "Config/System/Location".
- [Fw422007]: It was not possible to enter a name with
embedded spaces for "Config/System/Contact".
- [Fw421002]: (CPS-*-g and CPD-*-g products only)
Transmit power could not be changed via Web frontend.
SNMP
- [Fw422001]: SNMP-Agent got a wrong system uptime
in firmware version 4.22 only.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
- On a ComPoint running with DHCP enabled, a successful change of the IP address
with the ComPoint Manager may cause an error message such as
"Setup failed. Read() select failed cause timeout".
However, the IP address has been successfully changed.
See the release notes of the ComPoint Manager V2.10.
-----------------------------------------------------------------------------------------
Release Notes 4.22 28.07.2003
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
This Firmware Version 4.22 is a minor release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b, CPS-AP-g, CPS-BR-g, CPD-AP-g,
CPD-BR-g, CPD-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
Changes and improvements
Wireless
- Added "shortrange_mixed" mode to 802.11g profile settings.
- Changed factory default for 802.11g profile from "mixed" to
"longrange_mixed", in order to obtain interoperability with
clients that only support 1 and 2 MBit/s data rates.
- Upgrade of 802.11g Intersil Duette firmware version to 1.0.4.3.
- The data transfer rate "Actual speed" of bridge links
now shows the current speed instead of the maximum speed.
Bugfixes
Wireless
- [Fw420002 + Fw420003]: Entering a wireless network name with exactly 32
characters caused system to crash.
- [Fw420007]: In Bridge auto-configuration, it was possible to start
bridge configuration while scanning wasn't finished, leading to
"internal error" messages.
- [Fw420008]: Under heavy load conditions, associating a new client
to an AP could cause memory loss.
SNMP (CPS-* and CPD-* products only)
- [Fw420006]: System uptime retrieved by SNMP OID system.uptime
differed from the correct system uptime as shown by Telnet and Web UI.
Known problems
Wireless
- Currently, it is not possible to use a wireless network name (SSID)
of 32 characters. A wireless network name of 32 characters will be
truncated to 31 characters.
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
- On a ComPoint running with DHCP enabled, a successful change of the IP address
with the ComPoint Manager may cause an error message such as
"Setup failed. Read() select failed cause timeout".
However, the IP address has been successfully changed.
See the release notes of the ComPoint Manager V2.10.
-----------------------------------------------------------------------------------------
Release Notes 4.20 18.07.2003
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
This Firmware Version 4.20 is a major release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b, CPS-AP-g, CPS-BR-g, CPD-AP-g,
CPD-BR-g, CPD-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
Changes and improvements
Wireless
- Full compliance to the final 802.11g standard.
- Added support for PRISM Nitro mode for increased 802.11g performance.
Added Menu item to deactivate the 802.11g PRISM NITRO mode.
- For 802.11g radios, there is now a menu entry to adjust
the transmit power between 0 and 20 dBm.
- Upgrade of 802.11g Intersil Duette firmware version to 1.0.4.0.
- Upgrade of 802.11b Agere firmware version to 9.14.
- Bridge scanning improved: multiple links to the same partner
are no longer possible.
- Bridge scan result display improved: current bridge partner
is marked with "*" in the scan result list.
- Replaced the "state" entry in the AP node table by
the client's association time.
UI
- Renamed former wireless "WEP" menu to "Security".
Now the WEP key menu items are hidden unless
the "AuthMethod" is switched from "none" to "open/WEP".
Bugfixes
General
- [Fw411001]: When the wireless admin configuration had been switched
to "forbidden", under certain conditions, a filter rule conflict
prevented switching the configuration back to "allowed".
(UI: Control->Security->WL_admin)
- Broken Link Detection (BLD) could cause the ComPoint to hang
when BLD triggered a "link-down" of an 802.11g AP.
Additionally, the corresponding status LED wasn't updated properly.
Ethernet (CPS-* and CPD-* products only)
- There were two memory leaks in the Ethernet transmit routine.
- When connected to certain devices with "short" cables (up to 10 meters),
Ethernet could have very poor performance and high packet loss.
Wireless Bridge
- There was a memory leak in the Bridge transmit routine.
- [Fw411007]: 802.11g Bridge links died when partner was unreachable
for some minutes, requiring a disable-enable sequence or a reboot
to reactivate the bridge link.
SNMP
- [Fw411002]: The system sometimes performed a reboot
after changing SNMP parameters.
Known problems
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
- On a ComPoint running with DHCP enabled, a successful change of the IP address
with the ComPoint Manager may cause an error message such as
"Setup failed. Read() select failed cause timeout".
However, the IP address has been successfully changed.
See the release notes of the ComPoint Manager V2.10.
-----------------------------------------------------------------------------------------
Release Notes 4.11 23.06.2003
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
This Firmware Version 4.11 is a major release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b, CPS-AP-g, CPS-BR-g, CPD-AP-g,
CPD-BR-g, CPD-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
Changes and improvements
Bugfixes:
General
- Under heavy load conditions, a memory leak could lead to crashes.
Wireless
- Send roaming notification upon initial STA association didn't work.
Known problems:
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
- On a ComPoint running with DHCP enabled, a successful change of the IP address
with the ComPoint Manager may cause an error message such as
"Setup failed. Read() select failed cause timeout".
However, the IP address has been successfully changed.
See the release notes of the ComPoint Manager V2.10.
-----------------------------------------------------------------------------------------
Release Notes 4.10 17.06.2003
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
This Firmware Version 4.10 is a major release.
The firmware supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b, CPS-AP-g, CPS-BR-g, CPD-AP-g,
CPD-BR-g, CPD-XT-g.
and all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
Changes and improvements
New:
Wireless (CPS-BR-g, CPD-BR-g and CPD-XT-g only)
- Support for high speed 54 Mbit/s 802.11g added.
Wireless
- Upgrade of Intersil Duette firmware version to 1.0.2.0.
- AP now tries to actively kick out associated clients (if
supported by driver) instead of only clearing internal
node list, e.g. when security settings are changed.
- AP now sends multicast notification upon association
of any new client.
- Intersil 802.11g AP now supports association test,
i.e. clients with IP stack are thrown out when they stop
responding to ARP requests.
- Different 802.11g profile settings allow balancing between
maximum throughput and maximum 802.11b compatibility.
Wireless Bridge
- Entirely new remote bridge configuration via ARBOP, allows
selection of bridge partner from a list of available bridges.
UI
- Adapted link test display to handle 802.11g data rates.
- Added menu entry in config/ports/extended to select profile
for 802.11g/802.11b compatibility: (B only/Mixed/Mixed long range/G only).
- In AP node table statistics, only most recent frame data rates display S/N
in dBm, older lines display "---", making identfication of current data
rate easier.
General
- Slightly decreased power consumption by activation of
processor-internal "Dynamic Power Management".
Bugfixes:
Wireless (CPBR-2W11 only)
- [Fw300006]: plugged long-standing buffer memory leak in DoubleBridge.
Wireless AP
- Kick out all clients could cause STA to appear associated
but not to show up in AP node list.
UI
- [fw302015]: the menu item "Bridge links" in the telnet user interface
sometimes doesn't appear until a key is pressed.
Known problems:
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
- On a ComPoint running with DHCP enabled, a successful change of the IP address
with the ComPoint Manager may cause an error message such as
"Setup failed. Read() select failed cause timeout".
However, the IP address has been successfully changed.
See the release notes of the ComPoint Manager V2.10.
-----------------------------------------------------------------------------------------
Release Notes 4.00 27.05.2003
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
This Firmware Version 4.00 is a major release.
The firmware supports all the first-generation ComPoints:
CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware also supports the second-generation products ComPoint-II:
CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b, CPS-AP-g.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
Changes and improvements
New:
Wireless (CPS-AP-g only)
- Support for high speed 54 Mbit/s 802.11g added.
Wireless security
- Administration of the ComPoint over the wireless ports can be blocked.
Setting "Wl Admin" in "Control->Security" to "forbidden" adds an entry to
the MAC filter rule table, that blocks all outgoing traffic via the wireless
ports with source MAC address equal to the ComPoint's MAC address.
Changes:
General
- Performance improvement of IP packet processing,
in particular the processing of broadcasts,
subnet-broadcasts, and multicasts.
- MAC address learning with respect to wireless roaming improved.
Wireless (ComPoints with 802.11b cards only)
- ComCard firmware upgraded. This update improves the wireless
functionality in general (e.g. performance) and fixes some minor bugs.
Bugfixes:
Bootloader (CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b, CPS-AP-g only)
- The ComPoint's hardware was not propper initialized,
leading to sporadic crashes on power reset (cold start).
Wireless (CPBR-2W11 only)
- [fw330001]: DoubleBridge could crash on link test.
Protocol filter
- [fw332001]: The layer-2 protocol filter didn't perform
any filtering in certain cases (depending on the entered rules).
DHCP
- [fw330003]: ComPoint was not always accessible over TCP/IP
if enabling DHCP via the Telnet interface and the lease request fails.
Known problems:
DHCP
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
- On a ComPoint running with DHCP enabled, a successful change of the IP address
with the ComPoint Manager may cause an error message such as
"Setup failed. Read() select failed cause timeout".
However, the IP address has been successfully changed.
See the release notes of the ComPoint Manager V2.10.
-----------------------------------------------------------------------------------------
Release Notes 3.33 27.03.2003
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
The new Firmware Version 3.33 is a major release.
The firmware supports CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware also supports CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
Changes and improvements
Bugfixes:
Wireless
- [fw330002]: Wireless frame encapsulation wasn't
properly removed in some cases with the consequence
that Ethernet frames got too large.
Known problems:
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
- On a ComPoint running with DHCP enabled, a successful change of the IP address
with the ComPoint Manager may cause an error message such as
"Setup failed. Read() select failed cause timeout".
However, the IP address has been successfully changed.
See the release notes of the ComPoint Manager V2.07.
-----------------------------------------------------------------------------------------
Release Notes 3.31 24.03.2003
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
The new Firmware Version 3.31 is a major release.
The firmware supports CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware also supports CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
Changes and improvements
Bugfixes:
Wireless
- Display of signal strength values (dBm) in AP node statistics
showed incorrect values.
Ethernet
- Initialization of the Ethernet driver on restart (warm start)
could result in an undefined behaviour.
Known problems:
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
- On a ComPoint running with DHCP enabled, a successful change of the IP address
with the ComPoint Manager may cause an error message such as
"Setup failed. Read() select failed cause timeout".
However, the IP address has been successfully changed.
See the release notes of the ComPoint Manager V2.07.
-----------------------------------------------------------------------------------------
Release Notes 3.30 28.02.2003
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
The new Firmware Version 3.30 is a major release.
The firmware supports CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware also supports CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
Changes and improvements
Bugfixes:
Wireless (CPBR-2W11, CPD-BR-b only)
- [fw329001]: The Doubleridge crashed on
execution of a remote configuration.
This bug as introduced with firmware V3.28.
Known problems:
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
- On a ComPoint running with DHCP enabled, a successful change of the IP address
with the ComPoint Manager may cause an error message such as
"Setup failed. Read() select failed cause timeout".
However, the IP address has been successfully changed.
See the release notes of the ComPoint Manager V2.07.
-----------------------------------------------------------------------------------------
Release Notes 3.29 26.02.2003
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
The new Firmware Version 3.29 is a major release.
The firmware supports CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware also supports CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
Changes and improvements
Bugfixes:
Wireless
- Removed the "DTIM interval" configuration item
from the wireless bridge ports.
This AP-only feature provided with firmware V3.28
was added to the wireless bridge ports by mistake.
Ethernet (CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b only)
- [fw328001]: Weak performance if connected to a hub/switch
which has no auto-negotiation capability.
Configuration (CPS-BR-b only)
- The ComPoint CPS-BR-b in factory default configuration
started as AP instead of bridge.
This misbehaviour was introduced with firmware V3.28.
Known problems:
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
- On a ComPoint running with DHCP enabled, a successful change of the IP address
with the ComPoint Manager may cause an error message such as
"Setup failed. Read() select failed cause timeout".
However, the IP address has been successfully changed.
See the release notes of the ComPoint Manager V2.07.
-----------------------------------------------------------------------------------------
Release Notes 3.28 18.02.2003
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
The new Firmware Version 3.28 is a major release.
The firmware supports CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware also supports CPS-AP-b, CPS-BR-b, CPD-XT-b, CPD-BR-b.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
Changes and improvements
New:
Madge Discovery Protocol (MDP)
- Implementation of the Madge Discovery Protocol (MDP) server.
This feature allows wireless network management systems
with MDP support to discover ComPoints connected to the same LAN.
Broken Link Detection (BLD)
- The Broken Link Detection (BLD) is a mechanism to
determine the link status of specified wireless ports
due to results of ICMP ECHO request to a given IP address.
The virtual BLD IP link is considered as broken
if the specified remote host doesn't respond
within a given time period.
Wireless security
- Implementation of EAP-MD5/TLS/TTLS
to authenticate wireless stations.
User interface
- Config->System menu extended with the
SNMP system group parameters:
Location, Contact, and Description.
Added sub-menus for displaying Hardware,
Software, and Feature informations.
Changes:
Authentication
- The AclLocal configuration table moved internally
to the general configuration space.
As a consequence the AclLocal configuration
now get also lost if the ComPoint's configuration
is reset by the user!
Wireless
- IP packets with the IP-TOS field set to IPTOS_LOWDELAY
are now prioritized both in the ComPoint's internal buffer
management system and the wireless card.
- Performance improvement with WEP encrypted data transfer.
- Status/Port menu now shows both MAC addresses
for double bridge ports.
- Turning WEP encryption on/off now empties
the wireless node table, to ensure synchronicity
with the corresponding wireless card;
- The "Speed mode" setting for Bridge and DoubleBridge
now is stored persistently in the ComPoint's configuration.
- RTS/CTS threshold setting is now available for Bridge
and DoubleBridge. All bridge links share the same threshold.
- DTIM interval setting is now available for wireless ports
to select the number of beacon intervals that elapse between
transmission of beacon frames containing a TIM element
whose DTIM count field is 0.
- The list of selectable DS channels is now created dynamically
based on the supported channels of the wireless card.
User interface
- The Status->Software menu has moved
to the Config->System menu.
- The SNMP system group parameters Contact and Location
have been moved to the Config->System menu.
General
- Improved output messages to the system console.
Bugfixes:
Wireless
- [fw314002]: Media distribution of AP RTS/CTS threshold
to the associated clients corrected.
Telnet User Interface
- [fw311003]: ACL/EAP server configuration:
Range check for port numbers added.
- [fw311006]: MAC filter:
Corrected the display of certain filtering rules.
- [fw314001]: IP routes:
A zero address in the routing table
was shown as "no_default" instead of "0.0.0.0".
- [fw310002]: BR/BR2 Link test statistics:
Resetting the link test statistics now works as expected.
- [fw307002]: AP node table:
Clients with empty node names are now displayed as "802.11".
- [fw310001]: AP node table:
Special characters in the client's node name are now handled correctly.
Web User Interface
- [fw311004]: Fixed wrong behaviour of the user interface
if values containing white spaces are entered.
- [fw311005]: Fixed some minor navigation problems
which might occur while traversing the configuration hirarchy.
Known problems:
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
- On a ComPoint running with DHCP enabled, a successful change of the IP address
with the ComPoint Manager may cause an error message such as
"Setup failed. Read() select failed cause timeout".
However, the IP address has been successfully changed.
See the release notes of the ComPoint Manager V2.07.
-----------------------------------------------------------------------------------------
Release Notes 3.10 10.09.2002
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
The new Firmware Version 3.10 is a major release.
The firmware supports CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
IMPORTANT!
The ComPoint's factory default setting of DHCP has been changed
from "disabled" to "enabled". That means: resetting the configuration
forces a DHCP discovery on system restart.
You may change this behaviour by manually disabling DHCP.
Changes and improvements
New:
Multipoint Bridge
- For each wireless card configured as bridge, now up
to 6 links to different bridge partners can be configured.
The default names for bridges now are made like "wl1br1",
"wl1br2", with a unique number for each bridge link. There
is always at least 1 link for each bridge, i.e. the last
bridge link on a card cannot be removed.
- In Telnet menus, things had to be rearranged in order to allow
individual configuration of multiple links. The values for "DS channel",
"Speed mode", "Encapsulation" and the WEP settings are common for every
bridge link on the same card.
- User interface: For easier identification of bridge links,
user-defined alias names can be assigned to every bridge link.
The following restrictions apply to those alias names:
+ each name must be unique in the system, i.e. you cannot use
a name that matches another port's name.
+ The name must start with a alphabetic character.
+ The name may not be longer than 13 characters.
+ The name may not contain white space (" ") or non-printable characters.
- User interface: "Status summary" now shows a detailed list of every
configured bridge link, including signal strength information.
MAC filter
- The former MAC multicast filter has been extended to
a general MAC filter.
- The default rule (src=any - dst=any - ports=all) always present
in previous versions is no longer displayed explicitly.
- The access to the ComPoint configuration can be restricted
to certain ports (default: all)
Example: the rule (src=local - dst=any - ports=eth1)
allows configuration access only via the Ethernet port.
Telnet user interface
- Made Telnet Navigation easier: The system now remembers the current
menu item and brings you back to the same item when going "back".
- Added forced closing of Telnet session after 3 consecutive invalid
password entries in order to defeat brute force attacks.
- Compoint detects when the telnet client is in local echo mode and
issues a warning message.
- Improved user feedback by visible password entry with "*".
Changes:
Wireless
- In Access Point port statistics, a name is displayed for every client
if name is available, i.e. clients works with ComCard.
- For Bridge and Double Bridge, an automatic link check is now done
every 5 minutes. If there is no reply for 2 consecutive checks,
the bridge link status LED changes from steady light to blinking.
- Bridge status LEDs now changes from blinking to steady light
immediately after successful auto configuration.
- For Bridge and Double Bridge, Link Test is now possible without
disruption of bridge operation. As a consequence, there is no more
need (and no possibility) to enable/disable Link Test.
The "Link partner" menu item is no longer necessary for Link Test and has
been removed.
- Double Bridge port name has been changed from wl0_brx to wl1_brx.
- Aironet UC/MC support is considered obsolete and has been removed.
- Enhanced Roaming notifications, solving possible problems on switched networks.
- If opening a wireless port fails during ComPoint startup due to some
misconfiguration, the ComPoint no longer crashes but starts without
opening the offending port, giving the opportunity to correct
configuration via telnet.
WEP
- WEP keys are now displayed as "*****" or "*************", depending
on the length of the key entered (40 vs. 128 bit WEP encryption).
- WEP keys with embedded 0x00 bytes are now fully supported.
- WEP no longer gets disabled after performing a remote bridge
configuration.
- If there are unconfigured or disabled bridge links on a card, WEP is
disabled for that card on power-up. This is in order to allow remote
configuration of unconfigured bridge links. An entry in the system
log is written when WEP has been turned off for any port.
DHCP configuration
- Factory default has been changed to DHCP "enabled" state.
- DHCP gets disabled if user manually enters IP address configuration
via the user interface or the CPM. The user also can disable or
enable DHCP via Menu "DHCP->Status[enable/disable]".
- If user disables DHCP, the lease will be released and the
current static IP configuration is used. If a lease request fails the
static IP configuration is also used.
- The DHCP fallback IP address has been removed.
Now the static IP configuration is used instead.
- DHCP startup command has been removed.
Now the user can disable/enable DHCP using the "Status" command
in the DHCP menu.
- "DHCP options" menu has been renamed to "DHCP".
Authentication
- If the interface configuration changes, either explicitly
via an user interface command, or implicitly via DHCP, then
the enabled authentication clients (ACL and/or I802.1x)
now reopen their server connection automatically.
Ethernet Autonegotiation
- Now negotiation always takes place if the link partner supports it.
Manual setting of the link speed and duplex mode is possible only
if "Auto neg mode" is switched to "disabled".
Telnet User Interface
- The label "System reset" has been renamed to "Restart" in the "Control" menu.
- The label "Reset to FD" has been renamed to "Config reset" in the "Control" menu.
Bugfixes:
Telnet User Interface
- [fw300001]: Leaving the "Control/View Logs" menu with "q" caused the
telnet session to crash.
- Fixed random crashes of telnet sessions caused by excessive keyboard input.
IP Configuration
- [fw302021]: Fixed system crash during startup phase if a invalid IP
configuration has been stored.
Wireless
- [FW300007]: WEP encryption didn't work as expected if both 3rd and 4th WEP key
were not left empty. After reboot, system could come up without WEP even when
it had been turned on previously. Switching WEP on/off didn't always take
effect immediately.
- Fixed some race conditions in bridge mode which could crash the ComPoint when
link was turned off (e.g. by starting link test).
General
- [fw301010b]: Fixed sporadic failures during firmware upgrade via a
wireless bridge, CPM displaying "SoRecvN() select timeout" errors.
- [fw302018]: Fixed ComPoint crashes caused by sending lots of IP
packets to the ComPoint itself (i.e. flood ping).
- [fw275004]: Fixed wrong buffer handling of IEEE802 Ethernet packets (RFC 1042).
Under rare circumstances, sending IP packets to the ComPoint itself
could cause an immediate crash.
- [fw302004]: Fixed sporadic timing problems triggered by an internal timer overflow.
Known problems:
- Enabling or disabling DHCP via the Web interface may crash the ComPoint.
Changing the primary interface configuration while DHCP is enabled
may also crash the ComPoint. These problems may only occur if the ComPoint
is configured with a Web browser.
- On a ComPoint running with DHCP enabled, a successful change of the IP address
with the ComPoint Manager may cause an error message such as
"Setup failed. Read() select failed cause timeout".
However, the IP address has been successfully changed.
See the release notes of the ComPoint Manager V2.07.
-----------------------------------------------------------------------------------------
Release Notes 3.00 05.04.2002
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
The new Firmware Version 3.00 is a major release.
The firmware supports CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
Changes and improvements
New: Security General
- Full IEEE802.1x support.
- EAP support.
- Radius extended EAP/MD5 authentication support.
- WEP is extended to WEPplus.
New: Security ACL & EAP
- Implementation of a general authentication cache. ACL & EAP
entries are managed both in one cache.
New: Wireless
- New ComCard firmware (8.10).
- RTS/CTS threshold now selectable.
- Microwave robustness option is now available.
Note: Don't enable this one with SpectraLink phones!
- System scale also known as AP density is now selectable.
- Load balancing is now user selectable.
- Medium distribution (distribution of access parameters from
AP to clients) can now be switched on or off.
- Internal roaming of wireless clients.
New: Bridge/Double configuration
- RemoteConfig/RemoteMac also known as LinkTest/LinkPartner, i.e.
the MAC address of the remote ComPoint (bridge), is stored permanently
and doesn't have to be reentered after ComPoint restart.
Bugfix: Security ACL
- If ACL remote is enabled, internal roaming wasn't possible.
That means a client was not able to roam from one AP port
to the other on the SAME ComPoint (wl1_ap <-> wl2_ap).
- ACL remote startup problem fixed.
- Removal of WL clients does not work properly.
- Disabling or enabling ACL remote does not flush the ACL cache.
These bugs are fixed in the current release.
Bugfix: Wireless
- No "moved " log messages were generated by internal roaming
(e.g. client moved from wl1_ap to wl2_ap).
- User cannot srcoll through node table.
These bugs are fixed in the current release.
Bugfix: Bridge configuration
- Link test does not work with WEP enabled.
- Under certain circumstances, ComPoint could crash during switching
bridge link test on/off.
- After link test, status LED of the initiating bridge/double bridge
didn't resume continous light after re-enabling bridge,
instead continued blinking.
- For remote config and link test, it was possible to enter MAC address
of own ComPoint.
These bugs are fixed in the current release.
Bugfix: DoubleBridge
- Data rate (speed) of double bridge is shown incorrectly (11 instead of 22).
This bug is fixed in the current release.
Bugfix: DHCP
- ALthough DHCP is disabled the CP may accept a lease from a W2k DHCP
server.
This bug is fixed in the current release.
Bugfix: Flash/Configuration data
- There might be versions conflicts regarding the configuration data
if user up-/downgrades the firmware.
This bug is fixed in the current release.
Change: Security ACL
- Cache synchronization improved.
- Remote/local synchronization improved.
- Changing the SSID forces remote entries to get removed from the
authentication cache.
- Client entries with access right == AR_Denied will time out and get
removed from the authentication cache, if the synchronisation
timer expires.
- Interoperation with an ACL remote server is more tolerant and more robust,
if the server is unreachable or the ACL service is unavailable.
Change: Wirless configuration
- ComPoint XT2 starts with one access point port and one bridge port.
- Factory default for multicast rate is now 2 MBit/s.
- The factory default channels are changed:
internal slot (wl1) is 6, external slot (wl2) is 11.
- Switching from a bridge to an access point port while runtime starts
an access point with factory default if there is no configuration of
a access point port stored. Hence, the repeating mode of a
new dynamically created access points is also enabled.
Change: DoubleBridge
- Switching between a double bridge port and an access point
or bridge port does not force a reboot anymore.
Change: Access point
- Improved log entries for access point messages:
"Node xxxxx-xxxxx associated"-messages are now preceeded by the port name.
Change: User interface
- A major revision of the user interface was made. The menu and parameter
names are more user friendly and comprehensible.
Change: Filter
- The configuration of the multicast filter is set to
factory default, if the user downgrades to any version less than 3.0.
Change: SNMP
- On upgrade all configuration data except the SNMP manager entries is preserved.
If the user downgrades to any version less than 3.0, all SNMP entries get lost.
-----------------------------------------------------------------------------------------
Release Notes 2.74 29.01.2002
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
The new Firmware Version 2.74 is a major release.
The firmware supports CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
Changes and Improvements
Bugfix: A bugfix in the arp module improves the behavior of the
DHCP and the ACL clients.
Bugfix: AceMonitor
If a monitor client, e.g. the CPM, does not close the
connection to a ComPoint, the monitor server hangs forever.
Hence, it was not possible to upgrade a ComPoint's firmware
until a reboot.
-----------------------------------------------------------------------------------------
Release Notes 2.73 17.12.2001
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
The new Firmware Version 2.73 is a major release.
The firmware supports CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme1st.txt file for update instructions!
Changes and Improvements
Bugfix: Configuration
The ComPoint Manager (CPM) did not always discover
a ComPoint, if the IP address is "0.0.0.0".
This bug is fixed in the current release.
Note: This applies not, if a router is between
the ComPoint and the host running the CPM.
Change: Configuration
Security leaks regarding the access rights
to alter a ComPoint's configuration eliminated.
New: Configuration
New handling for simultaneous telnet/Web sessions implemented.
Note: If four Web/telnet sessions are already running,
and a new Web/telnet session request is pending,
this request can be granted only,
if one of the already running Web sessions
has been inactive for at least five minutes.
Note: Only one Web session per host is possible.
Change: Password configuration
Passwords with non-printable characters are ignored.
Change: Ethernet configuration
Manual Ethernet configuration corrected/improved.
The specified values such as autonegotiation,
speed, and mode are checked for consistency and
remain valid after rebooting the ComPoint.
Note:
- If at the ComPoint and at the connected device
autonegotiation is disabled, it's important to
set the speed mode on both devices to the same value.
If the modes are different, bad performance
or even no communication might occure.
- If one of the connected devices is not capable
of autonegotiation, the second device will use
the speed of the other device and will use
half-duplex mode.
Note: If at the device the ComPoint is connected to,
autonegotiation is enabled and disabled at the
ComPoint, the connected device might have problems
to recognize the desired speed and mode automatically.
New: Ethernet
Bridging of Ethernet frames up to 1536 bytes supported.
So VLAN frames are no longer discarded.
Bugfix: SNMP
Some of the system group values couldn't be changed.
MAC addresses in the ARP table couldn't be changed.
The ComPoint might crash on retrieving the ARP table.
These bugs are fixed in the current release.
New: TCP/IP stack
Generation of UDP checksums implemented.
Change: Filtering
- Filtering in general improved.
- Now IP multicast filtering is supported.
- If entering a rule's multicast address,
then all 6 bytes of the MAC address must be specified.
Bugfix: Access Point
Displayed values in the data rate statistics
of the node table have not always been correct.
This bug is fixed in the current release.
Bugfix: DoubleBridge
After rebooting the ComPoint, the link speed
sometimes dropped down to 1 Mbit.
This bug is fixed in the current release.
Change: Bridge configuration
- Bridge and DoubleBridge configuration imporved in general.
- Link test for Bridge and DoubleBridge added.
- WEP parameters are also configurable via remote configuration.
- Consistency check of the remote MAC address improved.
- Improved robustness against loss of configuration packets.
The remote bridge remains in "allowed" mode,
in case of a configuration failure.
- "DS_Channel" is now configurable via the "BridgePort" menu.
- Bridge management frames are now sent with 1 MBit data rate.
Note: Please upgrade the firmware on both Bridge/DoubleBridge
ComPoints, in particular before executing a remote configuration.
Change: DHCP client
- The DHCP client of the ComPoint supports DHCP Servers of
following Operating Systems:
Novell 4.11, Win2k, OS/2 2.4.5 (DHCP ver. 4.1),
Linux Kernel 2.2x (DHCP ver. 3), WinNT 4.0.
- Excluded settings of DHCP options in the DHCP menu. Options
1 and 3 (router and mask) are always requested, so a manual
configuration is not necessary. Other options are still
not available.
- There is only one fallback IP address which is used if DHCP at
startup fails and/or if a DHCP failed while renewing or rebinding
a lease.
- Status indication of a DHCP lease is improved:
DHCP_Options menu command lease:
Lease [none] : dhcp startup is disabled.
Lease [failure]: requesting a lease failed.
Lease [in use] : lease request succeded.
Summary view:
dhcp disabled : dhcp startup is disabled.
dhcp enabled : dhcp startup is enabled, but no lease.
dhcp failure : dhcp is enabled, but lease request failed.
dhcp in use : dhcp startup is enabled, lease request succeded.
- Use of fallback IP address if lease request failed:
DHCP startup is disabled and user triggers manual request: the
stored interface configuration is used, not the fallback IP address.
DHCP startup is enabled: the given fallback IP address is used.
Change: ACL local - User Interface
Removal of local ACL table entries improved:
Now the value "all" or one of the first 8
entries may be selected from the list.
If there are more than 8 entries at the table,
the 8th entry shows "uncompleted".
Unshown MAC addresses must be entered manually
at the prompt to get removed.
Change: ACL local - User Interface
MAC addresses (Edit/Remove) may now be
entered without seperators. This functionality is
generalized now and no longer specific to a module.
Change: ACL remote
ACL cache synchronization improved if the status
of the ACL server connection changes.
The connectivity-check to the remote ACL server
is improved in general.
-----------------------------------------------------------------------------------------
Release Notes 2.61 09.08.2001
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
The new Firmware Version 2.61 is a major release.
The firmware supports CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme file for update instructions!
New features
Protocol Filter
This firmware includes protocol filter. The menu for filter configuration is found at
the menu config>Filtering. A list of 30 protocols can be build. The filtered protocols
can be forwarded (bypassing the multicast filter), forwarded through multicast
filter (and be processed there) or discarded. A default rule specifies the action
for all protocols not listed, either forward, procMcstFlt or discard. Protocols are
identified by their protocol numbers used in dix-ethernet or SNAP headers (see RFC 1700).
Some protocols and protocol suites (for example "INET" including ARP and IP) have been
predefined.
Remote Config for Bridge and Double Bridge
A remote config option was added to the menu of Bridge Ports (config>Ports>Port_wlx_brX).
This option enables configuration of a bridge link to be done from one side. If a bridge
boots with bridge port disabled, this port is set to "remote config allowed". From
the other bridge, remote config can be performed after input of the RemoteMAC, which
is the MAC of the ethernet port (starting with 00:01:CD) of its remote bridge (the one
set to "remote config allowed").
ARPProcessing
The option ARPProcessing was added to filter menu. ARPProcessing replaces IPProcessing.
(The option DetermineIP of the former IPProcessing ist now always set.)
If ARPProcessing is ON, ARP Packets from or to wireless clients associated to any Access
Point port of the ComPoint will be forwarded as unicast to the specific client.
ARP-Requests to all other nodes will be filtered out at any Access Point port.
Changes and Imporvements
Change: The values of signal strength have been corrected.
Change: Port names have been corrected:
old values new values
Port_wl0 -> Port_wl1
Port_wl1 -> Port_wl2
and at DoubbleBridge configuration:
old values new values
LocalIntMac -> LocalCard1
LocalExtMac -> LocalCard2
RemoteIntMac -> RemoteCard1
RemoteExtMac -> RemoteCard2
Change: inactive PSP clients are now removed correctly from the node table.
Change: telnet menues are automatically updated if menue content changes.
(for example at remote config while establishing a link).
Change: DHCP client now always requests subnetmask explicit form DHCP server.
Bugfix: DoubleBridge (BR-2) did not transmit 802.2-LLC frames correctly. This
could prevent NetBIOS/NetBEUI and IPX-Packets from being transmitted.
This bug is fixed in the current release.
Bugfix: DHCP did not work correctly with DHCP servers of some vendors.
This bug is fixed in the current release (see change notifications).
Bugfix: configuration changes made at remote config have not been stored automaticaly.
This bug is fixed in the current release.
Bugfix: All through config menues, it could have happend, that valid arguments entered
at prompt had not been accepted.
This bug is fixed in the current release.
Known Problems
Remote Config sometimes fails configurating the bridge which initiated the remote
configuration, also the remote bridge was configured correctly. This causes the remote
bridge to switch to Link enable, whereas the other side remains unconfigured. No Link
can be established at this state. Remote config can only be performed again, if
the remote bridge is set to remote config allowed again.
Options: 1. set remote bridge to remote config allowed again.
2. enter the MAC adresses of RemoteCard1 and RemoteCard2 at the local bridge
manually and enable the bridge link.
This problem will be solved within the next release.
-----------------------------------------------------------------------------------------
Release Notes 2.56 04.07.2001
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
The new Firmware Version 2.56 is a minor release.
The firmware suppots CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme file for update instructions!
Changes and Imporvements
Change: discovery mechanism in Bridge mode improved. If two crads in
Bridge mode were used, the second card was displayed at discovery.
This is changed, only Bridge cards of other ComPoints are shown
Discovery now shows signal strength (dBm) and SNR (signal noise ratio).
Change: static route menue add / remove route corrected and improved
Bugfix: changing the default filter rule an reviewing it could have caused
the ComPoint to reboot.
This Bug is fixed in the current release.
Bugfix: Some older ComPoints could have shown wrong Product code after update.
This could cause ComPoint to improper work.
This Bug is fixed in the current release. In addition, the wrong product codes
will be corrected while updating to this version.
Bugfix: Using CPBR-2, troughput could have dropped dramatically, if very heavy
traffic load conditions occured at both coupled LANs at the same time.
This bug is fixed in the current release.
----------------------------------------------------------------------------------------
Release Notes 2.55 28.06.2001
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
The new Firmware Version 2.55 is a minor release.
The firmware suppots CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The new firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme file for update instructions!
Changes and Imporvements
Bugfix: CPBR-2 could hang for some time while transfering data under
heavy load conditions.
This bug is fixed in the current release.
Bugfix: during update proedure to Version 2.54 the product code of a
CP could have been changed to a wrong code. This could cause the
CP to disable one wireless port or to run into a Software failure.
This bug is fixed in the current release. In addition, the wrong product codes
will be corrected while updating to this version.
----------------------------------------------------------------------------------------
Release Notes 2.54 21.06.2001
Firmware Onair ARtem ComPoint/ComPoint BR and BR2 ARtem GmbH
www.ARtem.de
The new Firmware Version 2.54 is a major release.
The firmware suppots CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The new firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme file for update instructions!
New features:
SNMP agent
This firmware includes a SNMP agent for SNMP V1 and SNMP V2.
The public MIB2 is supported. There is actualy no private MIB.
The firmware supports beside SNMP-Set and SNMP-Get as well SNMP-Traps.
Changes and Imporvements
ACL remote:
Communication to ACL Server is improved and enhanced.
Bugfix: CP could hang up while booting connected to a 10BaseT ethernet under
heavy load conditions.
This bug is fixed in the current release.
Bugfix: CP could stop bridging frames from and to wireless and refuse new
association requests while connected to halfduplex ethernet.
This symtoms only occured under heavy load conditions at the ethernet.
This bug is fixed in the current release.
Minor changes at the User Interface.
Help texts (telnet) cleaned up.
----------------------------------------------------------------------------------------
Release Notes 2.47 22.05.2001
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
The new Firmware Version 2.47 is a major release.
The firmware suppots CP-W11-N, CP-W11-D, CP-2W11-D, CPBR-W11, CPXT-2W11, CPBR-2W11
as well as the Upgrade Kits CC-W11-STD-AP and CC-W11-STD-BR.
The new firmware is shipped as one file, ARtem Firmware Package (.afw)
IMPORTANT!
Please refer to the readme file for update instructions!
New features:
DHCP Client
If DHCP Client is enabled, the ComPoint retrieves configuration data
form a DHCP server
HTTP interface
The HTTP interface allows configuration changes using a standard WEB browser.
The interface provides all capabilities of the telnet interface.
ACL-remote
ACL remote is integrated into this firmware.
This option requires ACL Manager, which will be available soon.
Changes and Imporvements
Configuration Menue
The etructure of the configuration menue has been readjusted.
An error at the display of statistic data while using ACL local is correted.
Short LLC frames
A minor bug in the handling of very short LLC frames is corrected.
Reset Button
The Reset Button (Hardware dependend) has been changed to new function:
If the button is pressed while power up, CP will halt in Monitor state.
This enables basic settings to change and firmware upgrade.
There is no wireless function at this state!
The device will return to normal operation after performing a Reboot.
------------------------------------------------------------------------------------------------------------
Release Notes 2.38 08.02.2001
Firmware Onair ARtem ComPoint/ComPoint BR ARtem GmbH
www.ARtem.de
V.2.38 is a major release.
The firmware supports also ComPoint BR and
ComCards BR in 2nd slot of ComPoint
1. Compatibility
- This firmware ensures the compatibility to new update file format ".afw"
2. New features:
- Support of Bridge functionality in ComPoint
(enabled only for ComPoint BR or if ComCard BR is in 2nd slot
- Local Access Control List
- Password authentication of CPM-Software supported
3. Important note:
Setting the ComPoint to factory defaults does not affect
the following parameters:
- IP address
- Subnet mask
- Default gateway
- ComPoint Name
- Passwords for all 3 user levels
- Local Access Control Table entries
!!! There is no chance to reset the password of any
user level. Lost passwords require maintenance
at factory !!!
Please do not enable the "remote access control list" feature.
This feature is only supported by future remote software.
------------------------------------------------------------------------------------------------------------
Release Notes 2.34 04.12.2000
Firmware Onair ARtem ComPoint ARtem GmbH
www.ARtem.de
V.2.34 is a major release.
The firmware was redesigned to provide full access point
functionality and improved stability.
1. Update instructions:
- Use ComPoint Manager Software V.1.08 only
- Upgrade Monitor to V.1.17 and reboot
- Upgrade Firmware to V.2.34 and reboot
!!! Do not use earlier versions of ComPoint Manager !!!
!!! Do not install firmware before upgrading Monitor !!!
2. New features:
- User levels "admin", "user" and "view" available
- Extended telnet menue for configuration
- Ethernet port supports autonegociation (dynamically)
or fixed user settings
- ComPoint supports WEP64/128 encryption
3. Important note:
Setting the ComPoint to factory defaults does not affect
the following parameters:
- IP address
- Subnet mask
- Default gateway
- ComPoint Name
- Passwords for all 3 user levels
!!! There is no chance to reset the password of any
user level. Lost passwords require maintenance
at factory !!!
4. Known bugs
It is not possible to enable/disable WEP encryption in the
ComPoint configuration menue via wireless clients, only via
ethernet port.
!!! Do not try it via wireless clients !!!
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.