================================================================================
Funkwerk Enterprise Communications GmbH April 2006
NDIS Miniport Driver FEC W-Client Cardbus .11g for MS-Windows Version: 3.3.20.0
NIC Firmware FEC W-Client Cardbus .11g Version: 2.13.8.0
================================================================================
This README.TXT covers information that was not yet known or
available when the user documentation shipped with this product
was written. It includes update information, additional
installation instructions, limitations to the current version of
the product, and suggestions to solve known issues or problems.
TABLE OF CONTENTS.
1. SOFTWARE DESCRIPTION
2. SYSTEM REQUIREMENTS
3. NEW IN THIS RELEASE
4. INSTALLATION NOTES
5. TECHNICAL CONSTRAINTS
6. KNOWN ISSUES
7. TECHNICAL SUPPORT
--------------------------------------------------------------------------------
1. SOFTWARE DESCRIPTION
1.1 About this software
This driver supports the FEC W-Clients .11g
* FEC W-Client Cardbus .11g
* FEC-W-Client PCI .11g / ComCard54g PCI
* FEC-W-Client mPCI .11g / ComCard54g mPCI
--------------------------------------------------------------------------------
2. SYSTEM REQUIREMENTS
2.1 Operating System
This Driver is for the Microsoft Windows 98 SE, Windows Me,
Windows 2000 and the Windows XP Operating Systems.
--------------------------------------------------------------------------------
3. NEW IN THIS RELEASE
* Support for FEC-W-Client mPCI .11g / ComCard54g mPCI
--------------------------------------------------------------------------------
4. INSTALLATION NOTES
4.1 Standard Installation Windows Driver
- For Windows 2000, XP, ME, and 98SE read the
"FEC W-Client .11g Quick-Installation" - guide
Insert the PC Card, choose the driver's INF-File and go ahead.
ATTENTION: Don't make a automatic search for driver on the CD.
May be the incorrect driver will be installed!!
4.2 Configuration Utility
You can either install the Configuration Utility via the
artem CD Wizzard or you can call directly the
"FEC_W-Client_.11g\Win98-ME-2k-XP\Utility\Setup.exe"
to install the Configuration Utility.
--------------------------------------------------------------------------------
5. TECHNICAL CONSTRAINTS
* Cannot set TX rate for ADHOC.
* The adapter mode of G only can scan 11B AP.
--------------------------------------------------------------------------------
6. KNOWN ISSUES
1. Driver: Setting up an adhoc then running a while,
the connection will break off and must do these actions such
as disable/enable ,the connection can be recovered.
2. Driver: Small fragment can't run more than 4hours.
3. Driver: When testing Nitro XM using XG302 and XG902 ,
the throughput from XG302 to XG902 is relative lower than
from XG902 to XG302.
4. Driver: Under adhoc mode transmit Rate can't be setting
unless pull-insert card.
5. Driver: Setup a 11b adhoc if set transmit is more than 11M,
the throughput will up to more than 11M?
6. Driver: Can't connect linksys11g AP while other cards can.
7. Driver: From driver advanced page if selected Configuration
profile is Mixed can only set up an 11g adhoc?
8. The "FEC W-Client .11g" Utility does not support WPA2 at the
moment.
--------------------------------------------------------------------------------
7. TECHNICAL SUPPORT
7.1 Finding Information
On the artem Web Site you can find the most recent
device drivers, software updates and user documentation.
World Wide Web: http://www.funkwerk-ec.com
7.2 Contact Technical Support
If you encounter problems when installing or using this
product, or would like information about our other
artem products, please contact us .
* E-Mail (Hotline): hotline@funkwerk-ec.com
* E-Mail (Service): info@funkwerk-ec.com
* Phone (Service): +49-180-300 91 91-0
* Phone (Hotline): +49-180 300 91 91-550
================================================================================
END OF FILE
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.