Release Notes 1.62 07.12.2004 ARtem Onair ComPoint Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.62 is a minor release for the ComPoint Industrial products CPI-b-E, CPI-b-EE, and CPI-b-ES*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Changes Generic - Improved arp cache and bridge table management. Bugfixes Known problems Wireless - Maximum transmission rate for WPA is about 250 kB/s. ----------------------------------------------------------------------------- Release Notes 1.61 15.11.2004 ARtem Onair ComPoint Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.61 is a minor release for the ComPoint Industrial products CPI-b-E, CPI-b-EE, and CPI-b-ES*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Changes Generic - Set web page reload timer to 15 min. - Improved memory management. - Cleanup and improvements in the web interface. Bugfixes Wireless - [gen160-001]: Country information (802.11d) corrected. Known problems Wireless - Maximum transmission rate for WPA is about 250 kB/s. ----------------------------------------------------------------------------- Release Notes 1.60 26.10.2004 ARtem Onair ComPoint Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.60 is a major release for the ComPoint Industrial products CPI-b-E, CPI-b-EE, and CPI-b-ES*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Changes Wireless - Do not show the MAC of the ad-hoc cell when in ad-hoc mode, as this information is of no use to the outside and would cause confusion at best. Generic - Added workaround for Opera and Mozilla bug which resulted in not sending the reboot command to the device, as these browsers sometimes cached the CGIs. - Cleanup and improvements in the web interface. Bugfixes Generic - [gen-156-003]: SNMP traps were sent if traps are enabled, but SNMP is disabled. - [gen-156-002]: Subnet mask couldn't be changed alone. - [gen-156-001]: Entering all WEP keys at 128 bit could lead to WEP key configuration corruption. Known problems Wireless - Maximum transmission rate for WPA is about 250 kB/s. ----------------------------------------------------------------------------- Release Notes 1.56 11.10.2004 ARtem Onair ComPoint Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.56 is a major release for the ComPoint Industrial products CPI-b-E, CPI-b-EE, and CPI-b-ES*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Changes Wireless - Added systemScale ("AP distance") parameter. If this parameter is not set from the AccessPoint via "medium distribution", the value from here is used. - Reconnection to a WPA-enabled AccessPoint improved. Bugfixes Generic - [gen-153-001]: Fixed occasional stack overflow in OS. - [gen-153-002]: LLC packets with SNAP=0xAAAA received on the ethernet side caused MIC failures when WPA is used. Wireless - [ac-152-001]: WPA Authentication sometimes failed because of old credentials. - [ac-153-001]: WDS packets wrongfully sent to us were accepted and therefore caused a data loop. - [gen-153-003]: WPA: Multicasts were sent out even if not authenticated with an AccessPoint. Known problems Wireless - Maximum transmission rate for WPA is about 250 kB/s. ----------------------------------------------------------------------------- Release Notes 1.52 19.08.2004 ARtem Onair ComPoint Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.52 is a major release for the ComPoint Industrial products CPI-b-E, CPI-b-EE, and CPI-b-ES*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Changes Generic - Added WPA passphrase description (any char, length 8-64). - One-time WPA key generation computing time increased (only if setting a new key). - Send unicast ARP to AccessPoint after association respectively after authentication if in WPA mode. Bugfixes Generic - [gen150-001]: Saving the configuration with CPM was not possible. - [gen150-002]: Ethernet frames with RFC 1042 encapsulation and length < 0x600 weren't bridged correctly via wireless. Wireless - [ac-150-001]: Reassociation failed under rare conditions. - [ac-151-001]: Reassociation with WPA was not possible. Known problems Wireless - transmission rate for WPA-PSK max. 250 kBytes/s ----------------------------------------------------------------------------------------- Release Notes 1.50 27.07.2004 ARtem Onair ComPoint Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.50 is a major release for the ComPoint Industrial products CPI-b-E, CPI-b-EE, and CPI-b-ES*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Changes Wireless - switch off MAC multicast filter in Hermes 2 Bugfixes Wireless - WEP doesn't work with packets with more then 1492 bytes Generic - save config leads to TCP timeout at CPM and no possbility to open a new TCP connection Known problems Wireless - Transmissionrate for WAP-PSK max. 250 kBytes/s ----------------------------------------------------------------------------------------- Release Notes 1.45 17.06.2004 ARtem Onair ComPoint Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.45 is a major release for the ComPoint Industrial products CPI-b-E, CPI-b-EE, and CPI-b-ES*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Changes - send a gratuitous arp as soon as an interface comes up - added basic SNMPv1 functionality (MIB-II SystemGroup, ColdStart Trap) Bugfixes - changes of nodename cleared the IP config Known problems Wireless - Transmissionrate for WAP-PSK max. 250 kBytes/s ----------------------------------------------------------------------------------------- Release Notes 1.43 13.05.2004 ARtem Onair ComPoint Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.43 is a major release for the ComPoint Industrial products CPI-b-E, CPI-b-EE, and CPI-b-ES*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Bugfixes Generic - changes of nodename in CPM leads to switch off of the DHCP - device is unreachable behind a router - endless requests to the device leads to memory full and the device hangs up Known problems Wireless - Scan doesn't work in Ad-hoc mode - Transmissionrate for WAP-PSK max. 250 kBytes/s ----------------------------------------------------------------------------------------- Release Notes 1.41 16.04.2004 ARtem Onair ComPoint Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.41 is a major release the ComPoint Industrial products CPI-b-E, CPI-b-EE, and CPI-b-ES*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Bugfixes Ethernet - RX polarity setting corrected Known problems Wireless - Scan doesn't work in Ad-hoc mode - Transmissionrate for WAP-PSK max. 250 kBytes/s ----------------------------------------------------------------------------------------- Release Notes 1.40 27.02.2004 ARtem Onair ComPoint Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.40 is a major release the ComPoint Industrial products CPI-b-E, CPI-b-EE, and CPI-b-ES*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Changes UI - Show wireless status Bugfixes Wireless - Association to Intersil APs with SSID longer then 10 bytes was not possible - Ad-hoc mode works not correct Known problems Wireless - Scan doesn't work in Ad-hoc mode ----------------------------------------------------------------------------------------- Release Notes 1.37 12.02.2004 ARtem Onair ComPoint Workgroup/Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.37 is a major release and supports the ComPoint Workgroup products CPW-b-EE and CPW-b-ES, and the ComPoint Industrial products CPI-b-E, CPI-b-EE, and CPI-b-ES*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Changes Wireless - Additional wireless parameter: RTS threshold, load balancing, microwave robustness, medium distribution, multicast rate - WPA-Personal support. Generic - Number of bridged clients increased from 8 to 16. Bugfixes none Known problems none ----------------------------------------------------------------------------------------- Release Notes 1.35 22.01.2004 ARtem Onair ComPoint Workgroup/Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.35 is a minor release and supports the ComPoint Workgroup products CPW-b-EE and CPW-b-ES, and the ComPoint Industrial products CPI-b-E, CPI-b-EE, and CPI-b-ES*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Changes Wireless - 802.11d support for DE, US and Fr added. - Default value for WEP authentication changed to "open". Generic - Improved firmware upload performance. User interface - Statistic data for ethernet and wireless added. Bugfixes General - [ac134-001]: Scan without AP's found crashed the ComPoint. Known problems none ----------------------------------------------------------------------------------------- Release Notes 1.34 18.12.2003 ARtem Onair ComPoint Workgroup/Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.34 is a minor release and supports the ComPoint Workgroup products CPW-b-EE and CPW-b-ES, and the ComPoint Industrial products CPI-b-EO, CPI-b-EE, and CPI-b-ES-*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Changes User interface - [gen131-001]: Added firmware type and nodename to the Web browser's title. - [gen041-002]: Configuration: Wireless Interface -> Transmission Rate For better understanding the Auto Fallback labels are now fully qualified with the supported values. Bugfixes Wireless - [ac131-001]: Disabling the radio crashed the ComPoint after reboot and login until the configuration was reset. - [ac131-002]: Ad-Hoc mode didn't work. General - [bl126-001]: The bootloader's recognition and handling of the Monitor button state had an undefinied behaviour caused by a timing problem. As a side effect sometimes the Monitor software was executed on reboot instead of the firmware. Known problems none ----------------------------------------------------------------------------------------- Release Notes 1.31 02.12.2003 ARtem Onair ComPoint Workgroup/Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.31 is a minor release and supports the ComPoint Workgroup products CPW-b-EE and CPW-b-ES, and the ComPoint Industrial products CPI-b-EO, CPI-b-EE, and CPI-b-ES-*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Changes Wireless - Upgrade of 802.11b Agere Hermes-2 firmware version to 2.00. Bugfixes General - [gen130-001]: Reset to factory defaults crashed the ComPoint. Known problems none ----------------------------------------------------------------------------------------- Release Notes 1.30 25.11.2003 ARtem Onair ComPoint Workgroup/Industrial ARtem GmbH Access Client AC firmware www.ARtem.de This firmware version V1.30 is the first official release and supports the ComPoint Workgroup products CPW-b-EE and CPW-b-ES, and the ComPoint Industrial products CPI-b-EO, CPI-b-EE, and CPI-b-ES-*. The firmware is shipped as one file, ARtem Firmware Package (.afw) IMPORTANT! Please refer to the readme1st.txt file for update instructions! Changes none Bugfixes none Known problems none -----------------------------------------------------------------------------------------Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.