Release Note for B57DIAG Engineering Diagnostics.
==================================================
Due to interrupt sharing problem on some systems with older BIOS, interrupt test and all loopback test
will fail on some of these rare systems. If so, it is a bios problem and the way to get around this is to assign
the Device Under Test to another IRQ.
version 6.18
Bug Fix:
========
1. Problem: (7764)
-meep switch does not support boot code larger than 8K byte size.
Cause:
The issue is due to a software array be limited to 8K.
In case of the fiber boot code that has 12K size, not the whole file be stored.
Fix:
Once the this array size increase to 16K, it allow the the whole file be stored and the issue is fixed.
Impact:
All boot code has size larger than 8K byte will be affected.
version 6.17 (May 09, 2003)
Bug Fix:
========
1. Problem:
In engineering mode, when blast 1514 byte packet with a 64 bit 00000000FFFFFFFF pattern
System will hang.
Cause:
When the diag fill up the memory with the 64 bit pattern,
the software byte counter of the for loop did not increment correctly
and course memory overflow and hang the system.
Fix:
Corrected for loop index increment.
Impact:
It hang system when running with any 57xx chip.
New Addition:
=============
1. Problem: (CQ 7754)
Customer has requested to add a -n parameter to the sechk parameter within b57diag in engineering mode.
This would allow the test to run with the following behavior:
- Supress any prompts resulting from executing 'sechk'.
- Do not automatically correct for an invalid checksum
- The ability to display and log the sechk results should remain intact.
Change:
Added code to achieve the above.
version 6.16 (May 01, 2003)
Bug Fix:
========
1. Problem: (CQ 7676)
Diag show DEF lock up error message when testing Fiber cards (TBI_MODE).
Cause:
Diag applied Phy reset work around to 5703, 5704 in TBI_MODE.
This will cause the phy reset work around to fail and display DEF lock up error
message.
Fix:
Apply the Phy reset work around to 5703, 5704 and 5705 in Copper Mode only.
Impact:
As described above.
version 6.15 (April 29, 2003)
Bug Fix:
========
1. Problem:
1000BT external loopback test fail on 5704/CIOBE due to no link.
Cause:
5704/CIOB-E phy reset occasionally will cause Phy to lock up.
Once the phy has been locked up, it will not link up at 1000BT.
Phy reset is needed to unlock the Phy. The same can be found in 5703 and 5705
Fix:
Apply the same work around that has been introduce in V6.14 to 5703 and 5705
Impact:
As described above.
2. Problem: (CQ #7652)
When there are multiple different devices in a system and an
NVRAM update is done, the update stops at the first device
that does not match the ID in the image file. There can be
other devices that match the image file ID that do not get
updated.
Cause:
When a device ID does not match a file image ID diagnostics
exit instead of continuing.
Change:
Changed code to continue checking for device ID that match
the ID of the NVRAM file ID after an unmatched device ID
is found.
Impact:
As described above.
version 6.14
Bug Fix:
========
1. Problem: (CQ #7583)
The NVRAM and VPD test will fail if diagnostics is run for
many iterations.
Cause:
The life cycle of the NVRAM will be exhausted if the NVRAM
test (C1) is run for an extended period of time.
Change:
Modified the code so that write to the NVRAM is done only on
the first iteration when many iterations are executed.
Impact:
For life cycle testing use the diagnostics command "setest"
in a loop. The diagnostics command "nictest c1 -n=0" will only
run the test write operation on the first iteration.
2. Problem:
1000BT external loopback test fail on 5704/CIOBE due to no link.
Cause:
5704/CIOB-E phy reset occasionally will cause Phy to lock up.
Once the phy has been locked up, it will not link up at 1000BT.
Phy reset is needed to unlock the Phy.
Fix:
New routine has been added to do phy reset for 5704/CIOBE. This routine
will issue PHY_RESET and check if the reset is successful. If not,
another PHY RESET will be issued, until max "retry" reaches. Once the max
retry has been reached, a warning will be displayed and test will continue.
Impact:
Once a Phy lock up has happened and cannot be unlocked by issuing phy reset,
chip will not link up at 1000BT. It will fail the 1000BT external loopback test.
New Addition:
=============
1. Request: (CQ #7398)
When an invalid DOS command line option is entered,
diagnostics displays help screens showing valid command
line options. A customer requested that the diagnostics banner
be printed before the display of the valid commands.
Change:
Added code to achieve the above.
version 6.13
Bug Fix:
========
1. Problem: (ClearQuest #7429, #7464)
The CPU test fails on some 5701 systems.
Cause:
Diagnostic does not wait long enough for the CPU to finish setup.
Fix:
Modified the code the increase the CPU wait time.
Impact:
As described above.
2. Problem: (ClearQuest #7428)
Diag fails on 5700 - Mac loopback
Cause:
Diagnostic does not wait long enough for the CPU to finish setup during load driver.
Fix:
Modified the code the increase the CPU wait time.
Impact:
As described above.
New Addition:
=============
1. Request: (ClearQuest #7439)
When external loopback test D3 and D4 test fail provide different
error codes for failures at 10/100/1000 Mbit/s.
Fix:
Added code to achieve the above and documented new error codes.
version 6.12
Bug Fix:
========
1. Problem:
Some tests, such as ASF Test, MSI Test and Reg Test has been skipped for all b57xx except b5788.
Also HW_init will initialize chip the same way as 5788.
Cause:
The logic that indecate 5788 is the target device will always return 1.
Fix:
Diagnostics is modified such that the logic will truely indecate if 5788 is really the target device.
Impact:
As described above.
version 6.11
Bug Fix:
========
1. Problem: (ClearQuest #7217)
On some machines the 5901 is incorrectly classified and the
gigabit loopback test is run (should be bypassed) and fails.
Cause:
During a driver load the chip is reset but the diagnostics does
not wait for the firmware to complete (setup the PCI registers)
and this causes the 5901 to be classified incorrectly.
Fix:
Diagnostics is modified so it now waits for the firmware to signal
that it has completed execution (setup).
Impact:
As described above.
2. Problem: (ClearQuest #7264)
CPU Test of Dos Diag fails for 5700B3 LOM on Dell 6600.
The failure displays, CPU reset failed, register 5034 is 0x1d.
1)The problem does not occur in b57diag v6.07
2)The problem occurs in b57diag v6.08, v6.09, and v6.10
3)The problem is seen on both 5700B3 LOM
Cause:
Diagnostics does not wait long enough for the firmware to complete during the setup phase of the CPU test.
Fix:
Increase FIRMWARE_WAIT_TIME from 150 to 170 ms to allow firmware has longer wait time to load bootcode.
Impact:
As described above.
New Addition:
=============
1. Request: (ClearQuest #7288)
A customer requested that an error message is printed and an error
code of 1 is returned when an user enters an incorrect number when
selecting a card to run tests against from the DOS command line.
Fix:
Add code to achieve the above.
version 6.10
Bug Fix:
========
1. Problem: (ClearQuest #7217)
A 5901 is recognized as a 5705 during manufacturing and the gigabit
loopback test is run and fail because the device is a 5901.
Cause:
In manufacturing diagnostics programs the device's firmware and
then runs the manufacturing tests.
Before firmware is programmed the 5901 is classified as a 5705.
After firmware is programmed diag. did not re-classify the device
as a 5901.
Fix:
Added code re-classify the device after the firmware is programmed.
Impact:
As described above.
version 6.09
Bug Fix:
========
1. Problem:
Software mistaking 5705 device as 5788 and not allow user to update 5705 bootcode.
Cause:
The logic that indecate 5788 is the target device reported incorrect info.
Fix:
Diagnostics is modified such that the logic will truely indecate if 5788 is really the target device.
Impact:
This has been introduce in version 6.08
version 6.08
1. Added support to bcm5788.
Bug Fix:
========
2. Problem: (ClearQuest #7155)
User requested the following modification to the -elog option:
Create the error log file only if an error occurs.
If the error log file exists append to it.
Cause:
Modification Request.
Fix:
Added code to fulfill the user request.
Impact:
None.
New Addition:
=============
1. Request: (ClearQuest #7171)
User requested that the ability to print out the DID,VID, SDID, VID,
firmware, PXE, PXESpd, WOL, ASF and MBA options from a DOS
command line option.
Fix:
Added the DOS command line option -dids to provide the feature.
version 6.07
1. The space between the file name an -f option in 'upgfm' is no longer needed.
Bug Fix:
========
2. Problem: (ClearQuest #7155)
When viewing a log file there is not way to tell if a user stopped
the testing procedure via a <ctrl-c>.
Cause:
When the user presses <ctrl-c> logging is stopped.
Fix:
When a user presses <ctrl-c> the string "User Aborted Testing" is
logged to the log file.
Impact:
None.
3. Problem: (ClearQuest #7171)
When a log file is created and the flash update option is selected
then an incrementing address counter is displayed on screen and all
these incrementing values are written into the log file.
Cause:
The code does not disable logging of the flash address counter.
Fix:
Disable logging of flash address counter.
Impact:
None.
New Addition:
=============
1. Request: (ClearQuest #7155)
User requested that an error log file is generated when an error
occurs. Only error information is logged (NOT pass information).
Fix:
Added DOS command line option "-elog <file>" to provide the feature.
version 6.06
Bug Fix:
========
1. Problem: (ClearQuest #6748)
The diagnostics command 'memtest -c" fails on the 5705.
Cause:
The 5705 memory map is different than the 5700/01/02/03/04.
The present code does not take this into account.
Fix:
Use the 5705 memory map NOT the 5700/01/02/03/04.
Impact:
This test failed on the 5705 on previous version of diagnostics.
2. Problem: (ClearQuest #7171)
If a user used the diagnostics command line option "-m" to program
the MAC address the user HAS to enter the MAC address. If a user
ESCapes out of entering the MAC address the NVRAM gets corrupted.
Cause:
The MAC address entry routine was not coded to handle the ESCape
sequence correctly and corrupts the NVRAM.
Fix:
Modified the MAC address entry routine so that when a MAC address
is not entered (ESC pressed) the NVRAM is not corrupted.
Impact:
This "-m" corrupted the NVRAM on previous version of diagnostics.
3. Problem: (ClearQuest #7171)
When "b57diag -c 0 1 -e b57kia -m -n -t abcd" is run on a 5704 the
user is not allowed to exit out of diagnostics after the first
execution loop. The user is force to run the diagnostics loop two
time on each device before he is allowed to exit.
Cause:
Since the 5704 is a dual device the command above should run twice
(once for each device). Due to a coding error the user is forced to
run four times (twice for each device).
Fix:
Modified the code so the above test is run once per device.
Impact:
Described above.
New Addition:
=============
4. Request: (SQA request)
Users would like to update the PXE code from the DOS command line
using b57udiag.exe.
Fix:
Added the DOS command line -pxe option to diagnostics so that the
PXE code can be updated.
Impact:
None
version 6.05
1. Enable swapXBAR option in SECFG when 5404 B0 is detected.
2. Added 5703B0 ASIC Rev ID
Bug Fix:
========
3. Problem: (ClearQuest #7087)
The diagnostic DOS command line command option "-firm" fails
when programming multiple cards.
Cause:
In order to program the NVRAM a mapping has to be done from the
file image to an NVRAM image. When programming multiple cards
the mapping routine was mistakenly called multiple time. The first
call correctly preformed the mapping and the first card is
programmed correctly. All remaining call corrupted the NVRAM image
and the following card are programmed incorrectly.
Fix:
Call the file image to NVRAM image mapping routine once.
Impact:
Previous version of diagnostics will incorrectly program the
2nd-nth card.
version 6.04
Bug Fix:
========
1. Problem: (ClearQuest #5898)
Warning text is added to the D4 test. The warning text reads
"(** ZERO LEN LB RJ45 **)".
Cause:
Test D4 (screening for 1G Tx/Rx lines open/short) only works
with zero length (ie short) RJ45 loopback connectors.
Fix:
Text change in code.
Impact:
None.
version 6.03
Bug Fix:
========
1. Problem: (ClearQuest #6619)
When the NVRAM is updated via the DOS command line "-firm" command
the NVRAM update fails.
Cause:
The NVRAM image file was incorrectly mapped to the NVRAM.
Fix:
The NVRAM image file is correctly mapped to the NVARM.
Impact:
Image loaded to NVRAM with the with previous version of the
"-firm" command would not work correctly.
New Addition:
=============
1. Request: (ClearQuest #5898)
Customer requests to test for 1G Tx/Rx lines open/short.
Fix:
Inserted and coded test D4 for 1G Tx/Rx lines open/short testing.
Impact:
Original D4 and D5 test now change to test D5 and D6.
version 6.02
Bug Fix:
========
1. Problem: (ClearQuest #5898)
D3 (external loopback) test was modified so the it could
check for shorts and opens on the 1G lines of short RJ45 cable.
This test failed with long cables.
Cause:
Screening for open and short can be done only on short cables.
Fix:
Open/short screening has been removed from the D3 test so
that the D3 test would pass with long cables.
Impact:
Open/short testing not supported.
2. Change copyright string from Broadcom to OEM.
version 6.01
1. Fixed setorture command failure.
Bug added in code since v5.03 where the firmware bootup handshaking
is tested for twice, which causes the incorrect failure.
2. Bounds checking for udiag command line options added.
3. Added Support to 5705 A2/A3, 5901 A2/A3, 5705M A2/A3.
4. Added OEM NC7761 Gigabit Server Adapter support.
5. Modified Phy Interrupt test. Since the purpose of this test is to check if phy can update our interrupt
status bit (to generate interrupt) and we do not want to use actually
interrupt to test this feature we were polling the interrupt status.
Since some systems will randomly call our interrupt service routine and clears the
interrupt status, caused our polling routine to fail to see the interrupt
status. The workaround was not only polling for interrupt status in the register,
but also checks if actually interrupt service routine has cleared the status.
If the interrupt service routine clears the status, it will increment a counter to indicate that the status was cleared by
interrupt service routine.
6. Removed "Disable Expansion Rom Test" from Expansion Rom test.
Once the Expansion ROM is "disabled" on the system, when the diag is accessing to the Expansion ROM,
it in fact, is accessing to "non-existing" memory address. Depending on the system design, the system reaction to the
"invalid memory access" may be different, and it is very possible to hang the system.
version 6.00
1. Customer requested that DOS command line execution of the loopback
test D3 allow selection of line speed. Line speeds for this test
can be set via the command line option "-lbspd t/h/g", where
t/h/g is ten/hundred/giga line speeds.
To run ten and giga LB "b57diag -t abcd T D3 -lbspd tg"
2. A customer requested a DOS command line option to program the firmware
on a device, only if the did, vid, sdid, & svid of the device matches
the information in the firmware file.
Use "b57udiag -firm abc.bin" to program all device on a system where
the device did, vid, sdid, & svid matches the same information in
the firmware file "abc.bin".
3. 5704 support has been added to q57udiag.
version 5.18
1. Tx/Rx 32 bit packet counters are extended to 64 bits, to allow
for longer test runs without a counter rollover.
2. -w and -b options take no effect in dmaw cmd in engineering mode. These had been fixed.
3. HP NC7761 Gigabit Server Adapter PCI_ID has been added.
4. The 5705 would not catch a open on gigabit Tx/Rx lines during loopback.
Tap2, mean square error, on the DSP is used to screen for opens.
5. Stopping "blast -t -r -n=0" via ESC would stop the Tx/Rx simultaneously.
If packets are loopedback (LB) some packets would not be RXed due to the LB delay.
Fixed by first stopping Tx, then waiting, then stopping Rx.
version 5.17
1. Added 5704 A3 bond ID and Rev ID.
version 5.16
1. Extended 5705 status block non-error counters in software.
2. Modified 5705 reset sequence required for A2 chips.
3. Fix a bug in accessing flash while flash is not supported which will cause system hang. In bug is at the end of the CPU test.
4. Modified enabling Clock Run function
version 5.15
1. Fixed incorrect qstat cctet count for 2nd-nth 5705.
2. In q57udiag, -mbas speed option will only support auto for Fiber cards
3. In q57udiag, setmba and setpxe cmds will only support auto for Fiber cards
4. Fixed multiple do with parameter-passing bug
5. All loopback tests are using hw counters instead of software interrupts counters.
version 5.14
1. Mask out the all W2c bits in offset 0x6 of PCI CFG registers test.
version 5.13
1. Increase tx wait time in external loop back to allow all packets can be tx.
version 5.12
1. Fixed CPU test failure with correct reset sequence
version 5.11
1. Enable wol En/Dis options in q57udiag
2. Removed 5704 support in q5udiag.
3. After reset, software will enable clock-run bit in PCI cfg space if 5705 detected.
version 5.10
1. Added delay at the end of cpu test to let cpu fully complete loading fw.
2. Reduce the frequency of polling register during reset to avoid fighting between CPU and host.
version 5.09
1. "loadd" cmd will config link speed depend on card/chip type (FE/GE).
2. Fixed bug when running "blast" consecutively without a chip reset.
The bug was introduced in 5.07.
3. Removed cpu_mem_access test per Tak
4. Modified CPU test util_chip_global_reset to wait for CPU loadd fw completed.
5. Fixed bug when running "blast -t" where TXing eventaully stops.
6. Modified PCI cfg read mask to skip Bit 15 of offset 0x4c since this bit is w2c.
7. Enhance program ASF FW function in both engineering and manufacturing mode.
Version 5.08
1. Added 10 and 100 Mbit/s operational mode to the command line options
-tr and -hlb (pg. 13 in manual)
2. Added 5782 support.
3. Added new PCI Device for 5702 A3, 5703 A3
Version 5.07
1. Added command line option -tr (pg. 13 in manual)
2. Added command line option -hlb (pg. 13 in manual)
3. Made changes to the blast command to support above options
4. Modified the way that the diag checks for ASF version. (fixes ClearQuest 6113)
5. Modified the way to reset the chip.
6. Increase Phy reset time out.
7. Modified 5705 PCI cfg register 0x74 read mask.
8. Fixed standalone_exe flag.
9. Unset DMA once bit in case of 5701 running in PCXI mode.
10. Added support to 5705
Version 5.02
1. Added write function
2. Added option -j(jumbo packet) and -t(tcpseg) for loaddrv command
3. Overhauled t3_mem_pool_init routine for more memory allocation options
4. Fixed 5705 ROM Size Error
5. Added Intelligence Mechanism to fw / PXE updrades.
Version 5.01
1. Added 5704 A2 NVRAM write enable support
2. Added Configuratin check for TT mode to very secondary port ASF/PXE/WOL enable
3. Added Cofiguration check for NIC mode to warn user for both port set to 100mpbs
4. Finalized FE->GE feature with the latest spec.
5. Fixed checksum in sechk command for ASF.
6. Fixed cheksum in dir command for ASF.
Version 3.24
1. Fixed LED mode when loading driver
2. Added CPU debbuging command
3. Added Internal CPU GPR test
4. Added delay for both dmar & dmaw & bustest done polling
5. Added support for both CPU on Internal CPUGPR test.
Version 3.23
1. Fixed Indirect register test on oem system
2. Fixed asfcfg backward compatibility
3. Added delay after voltage change.
4. Fixed 5704S voltage setting value.
5. Added lowWaterMarkMaxRxFrame for txpkt and blast command
Version 3.22
1. Added multiple device DMA (bustest, dmar, dmaw)
2. Fixed dmaw/dmar -c option bug
3. Added detection for 5704 in oem products.
4. Fixed A5 PCI config. register test on 5704.
Version 3.21
1. Fixed 5700/5701 failure on oem machine.
2. Added delay for cpugprtest
3. Change voltage control in cpu general purpose register test.
4. Added 5704S Bond id support
5. Added Updated Bond id check for 5700
6. Fixed Voltage regular control correctly for 5704 secondary device
7. Removed debugging code.
8. Modified Mac source address during tx/rx
9. Added 5703SA2 Bond Id fix
Version 3.20
1. Added loopback packet options.
2. Added multiple boot agent options (-mba).
3. Added command line options for b57udiag.
Version 3.19
1. Fixed bond id checking for CIOB
Version 3.18
1. Enhanced cpugprtest to test under v1.1, v1.2, and v1.3
2. Added workaround for 5704 A1 for NVRAM access locking when NVRAM was invalid
3. Fixed a problem where clock control register is overwritten when driver is
loadded.
4. Added support for 5704S A1
5. Added support for 5705 (non-mobile version)
6. Added 5705 cputest failure workaround
Version 3.17
1. Inverted polarity for Auto Powerdown mode so that default Autopower
down is disabled.
Version 3.16
1. Removed some debug break points.
2. Fixed 5704 eeprom programming.
3. Fixed a bug causes 5703A3 to always read 133MHz PCI speed.
4. Added more statistics support for qstats commands.
5. Fixed an issue where Tx flow control cannot be set with drvrcfg command.
6. Added 5901 support.
7. Added Auto powerdown mode support.
Version 3.15
1. Changed so that Phy interrupt test is skipped for BCM5705 A0.
2. Added Mini-PCI configuration in secfg command.
Version 3.14
1. Fixed memory allocation in pxe programming code.
2. Added 5702fe exclusion for gig external lpbk.
Version 3.13
1. Added 5705 support.
2. Fixed a memory allocation error on some systems.
Version 3.12
1. Embedded bist data into codes to reduce number of released files.
2. Corrected some spelling errors.
3. Fixed -f option to program eeprom image with size greater than 8k.
4. Added ASF command line to program ASF firmware.
5. ASF firmware files to be read from a text file.
6. VPD Write test to run only once if in continuous loop.
Version 3.11.0
1. Added commands "dir", "asfprg" for end user purpose.
2. Fixed b57udiag freezing problem.
Version 3.10.0
1. Fixed Link polarity problem in loopback modes.
2. Implement Power Saving option for firmware and driver use.
Version 3.09
1. Fixed a bug when both -m -f are entered in 5704.
2. Fixed output messages when -fmac option is in use.
3. Fixed problem with EFI hanging when clearing nic statistics
Version 3.08
1. Automatically skips serdes loopback if external link is detected in fiber.
2. Fixed help command in engineering mode.
3. Fixed -fmac command line.
Version 3.07
1. Enhenced setest command.
2. Fixed reset -w option bug
3. Skipped ROM/PCI config regi. test for secondary device in Daul MAC mode 3 for 5704.
4. Create the first version of short diag -- b57sdiag
5. Changed Altima indirect access method workaround only specific to A2 revision
6. Changed to dynamic firmware debug printf
7. Fixed bustest in ikos system (need more time before checking data)
8. Added help menu and miscellaneous small changes per oem's request
Version 3.06
1. Fixed serdes loopback failures on some product
2. Added filename support for -geneep option
Version 3.05
1. Changed (shorten) delay time for 5704 NVRAM arbitration timeout
2. Fixe Fiber internal loopback problem.
Version 3.04
1. Fixed serdes loopback failures on 5701
2. Fixed Phy loopback failure on 5700
Version 3.03
1. Fixed Altima 1011/1012 screening process power on/off problem
2. Added tx/rx octal display on qstat command.
3. Changed stsblk command display format from 10-digit-number to 15-digit-number
4. Added manufacturing mode, concurrent nvram programming and pxe update capability
Version 3.02
1. Added workaround for 1011/1012
2. Fixed some indirect memory access bugs
Version 3.01
1. Added Fiber Voltage workaround.
2. Added -fmac <filename> option to program mac address from a file.
Version 3.00
1. Added compile option for b57udiag (user diag)
2. Code size reduction
Version 2.39
1. Added phy crc counter to engineering blast
2. Fixed multiple interrupt problem on 5700 B2/B1/B0
3. Fixed failure when WOL is enabled
4. Added prevention to program wrong eeprom.bin to device
Version 2.38
1. Added cread/cwrite command
2. Fixed broken phy workaround created in v2.37
3. Fixed sedump command to support ATMEL Flash
Version 2.37
1. Added 5704 support
2. Added 5704 A0 workarounds
3. Added geneep new configuration commands
4. Fixed bug for chicken and egg problem for LOM write protection
Version 2.36
1. Fixed flash corruption failure.
2. Fixed indirect register test failure.
Version 2.35
This version does not support more than 3 devices on a PCIX system. It would result
in register test A2 failure if 4 or more devices are in the system.
1. Fixed dma test problem in 5701/pcix.
2. Fixed a failure on phy interrupt test.
3. Fixed a failure on Rx Cpu test when loaded from the floppy drive.
Version 2.34
1. Added secondary device (for 5704) NVRAM configaration support
Cold reset instead of warm reset before exit
2. Fixed bustest problem with new DOS extender
3. Added pciinit function call before reset if engineering mode was
entered be noinit option to prevent reset & flash access fail problem.
4. Fixed NVRAM test failure
5. Fixed Register Faiure
6. Added legacy eeprom test for sedvt command
7. Added dynamic directory support
8. Fixed some bugs in seeprom cfg which did not save cfg completely.
9. Fixed loopback failure on 5700 for backward compatibility.
Version 2.33
1. Added seclock command
2. Added seinit command
3. Changed setorture command display
4. Added -e, -a, -w option to sedvt command
Version 2.32
1. Added coverage for 5702FE
2. Handle appropriate link polarity for OEM in PHY loopback test
Version 2.31
1. Added memory test patterns to memory test
2. Replaced dos4gw dos extender to pmodew
3. Added fix to eeprom corruption problem
4. Fixed IRQ9 hanging problem
Version 2.30
1. Restored the original prompt :> instead of >
2. Fixed function/do command parameter passing bug
3. Fixed version string problem
4. Extended wait time for firmware after reset
5. Fixed ROM_test/VPD_test failure
6. Fixed upgfrm command bug
7. Added -r option for reset/pcii command to not to halt CPU
8. Changed sechksum command
Version 2.29
1. Fixed function printf() parameter bug
2. Appended CRC for ASF image programming
3. Changed sechksum command to display every block checksum in the directory
4. Support two phase boot code
5. Changed upgfrm algorithm
6. Changed secfg to support more configurations
7. Added user define function
8. Added parameter passing for user defined function and do commands
9. Added auto malloc()/DPMI memory detection algorithm
Version 2.28
1. Fixed problem with firmware response
2. Fixed problem with eeprom corruption
3. Fixed MSI test to avoid device string corruption
Version 2.27
1. Fixed atmel bitbang, seread bug
2. Fixed -i option for 5703A1
3. Fixed bug for Gigabit link issue. -- not to force Master all the time.
4. Added 'skips'
5. Fixed EEPROM size detection bug
6. Fixed Rainer 1000 link problem
7. Removed test engineering test B8 from test menu
8. Fixed error control on test D3
9. Add loading escape if ASF hangs
10. Add ASF cold and warm boot simulation
11. Add WOL configuation in menu
12. Fix smbout parameter issue
13. Added Error Control
14. Removed flshprg command
15. In manufacturing mode:
ROM_test (C7) is skipped for 5700/5701 running on PCIX-bus.
BIST_test (A4) is skipped for 5700/5701.
MSI_test (D4) is skipped for 5700/5701.
16. Removed ROM disable test from 5703_A0 device.
Version 2.26
1. Changed MBUF water mark for BCM5702/BCM5703.
Version 2.25
1. Fixed 5703 register 0x4c00 bit 31/30 error (should be no problem with 5703 A1)
2. Fixed external loop hang problem
Version 2.24 <Pending>
1. Added support for bridge detection and testing
2. Changed nictest command. It take "test list" parameter. By defaut, disable EEPROM content check in engineering mode
3. Separated register test for each board.
4. Added pcicfgtest
5. Added bitbang mode for atmel/stt FLASH device
6. Added passthru mode for all atmel/att Flash and seeprom
7. Fixed @ sign (multiple device command parameter bug)
8. Added ROM disable test
9. Fixed scratchpad memory test in conjunction with runing firmware bug.
Version 2.23
1. Updated 5703 register test
2. Updated DMA test
3. Added individual register test with back-to-back access
4. Fixed Interrupt test failing on BCM5700
Version 2.22
1. Fixed eeprom programming 4k/8k problem
2. Fixed 5704 register test
3. Fixed receive mask error for 5704 XBar mode
4. Fixed MIItest failure
5. Fixed 5704 xbar mode, interrupt line bug
6. Unconditionally enables RX/TX cpu clock at start up
(it may be possible disabled by bootcode for WOL)
7. Added Bist test
8. Added back-to-back access register test option
Version 2.21
1. Moved changes from bcmdiag version 2.6 - version 2.9
2. Changed t_writemem16, t_writemem8, t_readmem16, t_readmem8 from big endian to little endian
3. Separated regtest for 5700, 5703, and 5704
Version 2.20
1. Fixed blast -q option bug
2. Fixed ASF eeprom programming gap filling bug
Version 2.19
1. Fixed Register test
2. Restore letency timer/cache line value after reset
3. Fixed sleep command
4. Fixed rs232 echoing
5. Fixed register test: regster 690,694 -> 590,594
6. Fixed Broadcast config.
7. Changed IKOS flash clock devider to zero
Version 2.18
1. Fixed VPD test
2. 5703.bin update
3. flshdiag.bin update
Version 2.17
1. Stablizing tx/rx test
2. Fixed memory allocation bug
3. C5/D4 tests still have to be disabled
4. D2 test has to be disabled due to board design
Version 2.16.2
1. command clearbit bug fix
2. added checksum report for bootstrap on sechksum command
3. Added MSI test. Due to chip bug, this test will not pass on 5703 A0 chips
4. Fixed setest failure after running romtest.
Version 2.16.1
1. Memory Leak fix
Version 2.16
1. Added support commands for engineering mode
2. Added auto-polling test to mii_test
3. Added 10MB loopback test
4. Fixed "Stack Overflow!" bug
5. Fixed romtest/vpdtest
6. Added Backword bcmediag compatibility syntax for upgfrm command
7. Merged board to board test with Fiber Test
8. Fixed command line option -i to seach for invalid device id.
9. Stablized link in TBI/engineering mode.
Version 2.14
1. Finalize external memory test coding
2. Added external memory test option
3. Added external memory code execution test into external mem test
4. Fixed wol/pxe enabling/disabling problem
5. Enhanced -x & -w options to accept inputs 0/1 for disabling/enabling
Version 2.13
1. Correct FCS error statistic read
Version 2.12
1. Fixed a bug in PXE programming code
Version 2.11
1. Fixed DMA failure for specific OEM
2. Fixed failure on an OEM PCIX bridge
Version 2.10
1. Added detection for specific OEM
Version 2.09
1. Removed un-neccessary command line options
Version 2.08
1. Correct Silicon revision
Version 2.07
1. Fixed external loopback failure in version 2.06
2. Added command line option to view eeprom binary file
3. Disable WOL update function
Version 2.06
1. Fixed TBI mode failures on phy_type problem
2. Fixed Specific OEM message
3. Enter OEM manufacture code to handle link polarity in loopback tests
Version 2.05
1. Fixed DMA on PCIX failure
2. Take out packet # on loopback tests
3. Change order of tests per customer request
4. Fixed external loopback failure
5. Changed VPD test
6. Added -all option
7. Added -noinit option
Version 2.04
1. Fixed copper mac loopback hang problem
2. Fixed D3 loopback link problem
Version 2.03
1. Added Phy type/led mode/voltage source/part revision selectability in eeprom.txt
2. Added real/customer rev options
3. Speed up prog. pxe
4. Mac I/O reset
Version 2.02
1. Added TBI support
Version 2.01
1. Added FORCE_PCI and VOLTAGE_SOURCE to EEPROM.TXT file.
2. Changed secfg command to support FORCE_PCI and VOLTAGE_SOURCE
3. Added -coe to continue on error
Version 2.00
1. Fixed IRQ9 problem on specific OEM
2. Fixed Interrupt test failure reported from QSA
3. Fixed CPU test problem reported from Systems Engineers
Version 1.29
1. Skip test on NIC card that has ODI loaded
2. Fixed loopback hanging problem by adding delay time to ISR
Version 1.28
1. Added generic key code for eeprom generation
Version 1.27.1
1. Fixed a bug in manufacturing mode
2. Added compile option for specific oem
Version 1.27
1. Added sramtest command to test external memory in engineering mode
2. Added dbgmode to set a debug mode flag in engineering mode
3. Removed xmtest option which is not really needed
4. Added patch in loopback test to lower expectation on reception in case of chip testing
5. Modified external memory test routine
6. Added options debug/nocrc/chip/mac
7. Modified LoadPatchFirmware routine
8. Modified testfailed routine to enter engineering mode if fails and debug option entered
9. Fixed bug in eeprom programming
Version 1.26
1. Checked-in the fix for HP shared 9 interrupt issue (enabled back irq9 interrupt)
2. Fixed a bug in loopback tests
3. Fixed IRQ sharing with another device, such as Intel NIC, on memory read problem
4. Added CRC patch from Engineering for 5701
Version 1.25 (Internal Verion)
1. Added -debug option, when it fails jumps to debug prompt
2. Reduced timeout wait time
Version 1.24
1. Fixed bug in the load_firmware routine
2. Disabel IRQ9 chaining
Version 1.23
1. Added support for BCM5701-A0
2. Fixed interrupt chaining with IRQ9
Version 1.20
1. Changed to jump into command mode when no card detected with option -b57eng
2. Revise options -x and -w as following:
When nothing entered, always disable PXE/WOL
When -x or -w is entered, always enable PXE/WOL
When -f is entered, use eeprom.bin's content for PXE/WOL/PXE speed setting
When -f is entered and -x or -w is also entered, force PXE or WOL to enable
Version 1.19.3
1. Changed -f option to use eeprom.bin PXE and WOL setting instead of forcing to disable
Version 1.19.2
1. Changed software to exit directly to dos when no card was detected. No ESC needed
Version 1.19.1:
1. Added Altima/5411 support
2. Added loop command
3. Added mrloop command
4. Added option -geneep, -geneepkey
5. Added option -ver to display current version number
6. Removed mac_pref.txt input file for mac prefix -> now should use eeprom.txt to update eeprom.bin.
The eeprom.bin prefix is used if the mac input is less than 12 digit.
7. Added RJ45 external loopback for 100/1000
Version 1.19:
1. Add -xmtest option to increase memory test coverage
2. Reverse some coding on eeprom file dumping that is no long needed
3. Change eeprom programming counter display from hex to decimal
4. Added B7 MBUF memory special test
5. Put back interrupt chaining except irq9
6. Increased MAX_DEVICE from 8 to 16. Now it can support up to 16 devices
7. Fixed bug to restore phy state from isolated mode after test
Version 1.18e:
1. Fixed EEPROM access hang when loopback connector is connector is connected
Version 1.18:
1. Fixed IRQ 9 test D1 hang problem.
2. Restored LED to LINK3 LEDMODE after phy loopback test.
3. Added command rm.
4. Fixed MAC address display bug.
5. Added Link speed 10 test A1,A2 failure problem with workaround.
6. Changed -bus option to test specified slot only. This option is invalid if -c option is used.
7. Fixed intermitent failure/system hang problem when loopback connector is connected
Version 1.17:
1. Change MAC address reading to accept variable length instead fixing to 7 digits.
Version 1.16:
1. Changed the parameter misspelling "-dmpi" to "-dpmi"
2. Fixed the EEPROM size 0x204 programming bug due to the structure size define error.
3. Display not only device number but also bus:dev on error messages
4. Fixed Test D1, "Cannot Tx Packet" bug.
5. No sharing on IRQ 9
Version 1.15:
1. Added command line option -dpmi to use DMPI method memory allocation
2. Added command line option -bus bb:dd:ff to test against specified bus & device number
3. Displays device number on error message
Version 1.14:
1. Fixed PCI-X eeprom access bug.
2. Invalidate the default xx-xx-xx-00-00-00 mac address. However, it allow user
to enter mac address as xx-xx-xx-00-00-00.
Version 1.13:
1. Fixed Memory Allocation Problem for Dell 8450.
2. Added PCI-X support
3. Programmed MAC (in PCI-X mode) to not allow set the Relaxed Ordering Bit in
the Requestor Attributes of transactions it initiates that do not require
strong write ordering.
Version 1.12:
The new options -n, -m, and -f now requires -e option to be activated
1. New Option -n
With this option, the program will run in manufacturing loop.
It supports power on/off of UUT. This will ignore the option -I,
the iteration option.
2. New Option -m
Prompt user for the MAC address. With this option, user must enter/scan
the mac address before testing. The program also checks for the file
"mac_pref.txt" This is a text file should contain six digits of ASCII
MAC three-byte-prefix address. Any of the following format is supported:
Example:
000467
00 04 67
00
04
67
If this file exists, user has option to enter/scan 7 digit hex number.
The first digit will be ignored and the last 6 digits will be used for
the lower part of MAC address. Combine with the prefix, it creates 6
byte (12 digit) hex number.
If this file does not exist, the whole 12 digit number must be entered
for the MAC address. When entering MAC address, a space character is
allow between each byte. For example, any of the following is valid.
000467010203
00 04 67 01 02 03
1010203 (currently, the scanner uses this format)
3. New Option -f
Program "eeprom.bin" into EEPROM before testing. The file "eeprom.bin"
must be there or the program will not run with this option.
The -m and -f combination will create the following behavior:
a) -f and -m:
Program will not validate the eeprom content and go ahead to prompt
user for the MAC address. It programs MAC address and EEPROM content
and then checks the validity of eeprom content at the end of
programming.
Loading EEPROM content from eeprom.bin: passed -- enter MAC address after pass here
Programming EEPROM from eeprom.bin....: passed
Checking EEPROM content...............: passed
b) -f only
Program will check the validity of eeprom. If it is not valid,
it will act as a), -f -m option. If it is good, it saves the MAC
address from eeprom, program new eeprom.bin content into EEPROM
and then restores the original MAC address. It checks the validity
of eeprom content once more at the end of programming.
Checking EEPROM content...............: passed
Loading EEPROM content from eeprom.bin: passed
Programming EEPROM from eeprom.bin....: passed
Checking EEPROM content...............: passed
or
Checking EEPROM content...............: invalid
Loading EEPROM content from eeprom.bin: passed -- enter MAC address after pass here
Programming EEPROM from eeprom.bin....: passed
Checking EEPROM content...............: passed
c) -m only
Program will check the validity of eeprom. If it is not valid,
it will act as a), -f -m option. If it is good, the program will
prompt the user for a new MAC address and program the MAC address
only. It checks the validity of eeprom content once more at the
end of programming.
Checking EEPROM content...............: passed -- enter MAC address after pass here
Programming MAC address...............: passed
Checking EEPROM content...............: passed
or
Checking EEPROM content...............: invalid
Loading EEPROM content from eeprom.bin: passed -- enter MAC address after pass here
Programming EEPROM from eeprom.bin....: passed
Checking EEPROM content...............: passed
d) no -m and -f options
Program will check the validity of eeprom. If it is not valid,
it will act as a), -f -m option. If it is good, it proceed to
normal diagnostics.
Checking EEPROM content...............: passed
or
Checking EEPROM content...............: invalid
Loading EEPROM content from eeprom.bin: passed -- enter MAC address after pass here
Programming EEPROM from eeprom.bin....: passed
Checking EEPROM content...............: passed
4. Fixed -x -w option checksum false error report bug
Version 1.11:
1. Added features to secfg command to allow users to program VPD-R and
VPD-W information.
2. Removed all debugging information to reduce file size.
3. Manufacture test includes EEPROM content testing. If manufacture checkusm
is bad, it prompts user to enter MAC address. If the checksum it good, it
will save the mac address before programming eeprom.bin if user choose to
do so.
4. Changed Internal MAC loopback test from 100 to 200 packets.
Changed Phy loopback test from 100 to 2000 packets.
Changed RJ45 loopback test from 100 to 2000 packets.
5. Removed pattern and altenate pattern test from memory test to increase speed.
6. Removed VPD test to increase speed. Since both eeprom test and vpd test
exercise hardware eeprom. There is no needs for extensive test for both.
Version 1.10:
1. Removed bit 13 register 11 read only bit test for MII test
The MDI Crossover state bit changes internally when there is no cable
connected. It is not reliable to be tested as read only bit and it is not
an error.
2. Suppressed the error dialog when run without -p option
Version 1.09:
1. Moved over bcmediag.exe version 1.24 - 1.30 changes.
bcmediag.exe Version 1.30:
a. Added bustest to test out PCI bus in the worst case scenarios. The goal is
to have every data/control lines toggled.
Usage : bustest -a=address -n=iteration -l=min_len -h=max_len
-i=transaction -s=start_case -e=end_case
-a : NIC address to DMA data to.
-l : Minimum length (default = 256).
-h : Maximum length (default = 1024).
-n : iteration (default = 1)
-i : Number of transactions per pattern (default = 10)
-s : Start of test case (default = 0)
-e : End of test case (default = 259)
There are total 260 test cases (258 unique tests cases) which
are described as follows:
Test case# Pattern
========== ==================================
0 ffffffff ffffffff 00000000 00000000
1 ffffffff fffffffe 00000000 00000000
2 ffffffff fffffffd 00000000 00000000
. .
. .
. .
64 7fffffff ffffffff 00000000 00000000
65 00000000 00000000 ffffffff ffffffff
66 00000000 00000000 ffffffff fffffffe
67 00000000 00000000 ffffffff fffffffd
. .
. .
. .
129 00000000 00000000 7fffffff ffffffff
130 00000000 00000000 ffffffff ffffffff (repeat)
131 00000000 00000001 ffffffff ffffffff
132 00000000 00000002 ffffffff ffffffff
. .
. .
. .
194 80000000 00000000 ffffffff ffffffff
195 ffffffff ffffffff 00000000 00000000 (repeat)
196 ffffffff ffffffff 00000000 00000001
197 ffffffff ffffffff 00000000 00000002
. .
. .
. .
259 ffffffff ffffffff 80000000 00000000
If you run bustest command without any parameters, it will perform
DMA testing on all 260 patterns with 10 iterations per pattern and
different data length in each iteration. First eight bytes of data
are used to store the following info for debug:
byte 0-4 : length
byte 5-6 : iteration#
byte 6-7 : test case#
b. Added PCI-X support and work-around for B1 silicon. This version
diagnostics detects if the NIC is in PCI-X slot. If yes, work-around
is implemented. However, user still can overwrite this by issuing
debug -c=5 to toggle PCI-X work-around before loading driver.
bcmediag.exe Version 1.28:
a. Made minor changes to support B1 silicon due to changes in ASIC revision
format.
bcmediag.exe 1.27:
a. Added new commands to utilize BCM5500 built-in BERT features. Three
new commands are added:
* lbertram: load BERT pattern into BERT TX&RX RAM, and enable BERT.
* dbertram: Dump BERT TX& RX RAM.
* bertstats: Display BERT statistics.
bcmediag.exe Version 1.26
a. Changed initialization of BCM5500.
bcmediag.exe version 1.25
a. Added support for Serdes PHY (BCM5500) and TBI interface.
b. Added code to allow transmit jumbo frames up to 9022 bytes/packet
with txpkt command. (Note that you have to delete diagcfg.bin
before run bcmediag if you want to transmit jumbo frames over
4Kbyte/packet).
c. Added PCI-X support and work-around for B0 silicon. This version
diagnostics detects if the NIC is in PCI-X slot. If yes, work-around
is implemented. However, user still can overwrite this by issuing
debug -c=5 to toggle PCI-X work-around before loading driver.
bcmediag.exe version 1.24:
a. Enhanced txpkt/txcfg command to allow users to:
* Transmit random IP headers including IP options.
* Transmit random TCP headers including TCP options.
* Transmit random data payload.
b. Added code to check IP/TCP/UDP checksums of incoming packets.
2. Changed command user interface routines. This changes some of command syntax
3. Fixed WOL spelling
4. Change command help output.
5. Added -p option to print on Error
6. Display error on Red dialog with option to continue or print
Version 1.08:
1. Put delay in test C3 to avoid low priority DMA test error
2. Replaced original nictest with manufacturing tests
3. Fixed domument error code error, error code number 28 and greater was
shifted by 1.
4. Added error code 39,40,41,42
5. Changed test B5. External RAM test to detect the existance of external
RAM first for testing
Version 1.07:
1. Changed ESC to CTL-C as break key
2. Changed -t and -T option to allow multiple group specification in one option
3. Changed test D3 to be disabled by default
4. Added "Unit Under Test: NIC" line at error output
5. Unload all drivers upon exit
Version 1.06:
Added -I option for iteration
Version 1.05:
1. Rewrote all tests to comply to OEM's manufacture error message requirement
2. Added -t to disable tests and -T to enable tests
format: -t <gnnn> where g is the group letter can be A,B,C, or D
n is the subtest number it should be '1' to '9'
example: -t A345 -t C13 -T b12 this will disable test A3,A4,A5,C1,C3
and enable test B1,B2.
Version 1.04:
1. Added -m option to disable RJ45Loopback Test
Version 1.03:
1. Fixed multiple card interrupt problem.
Original call had only one variable to save original interrupt
vector. If multiple cards use different interrupts, some origianal
interrupt vector get lost. This will cause problem after exiting program.
Code is changed to support shared interrupt as well.
2. Comment out some unreachable code in order to reduce code size.
Version 1.02:
1. Added changes due to changes in boot code firmware 0.6. Before issuing
CHIP reset (or GRC reset), it writes a siginature to SRAM so that
firmware wouldn't perform code boot initialization such as PHY
H/W reset, PXE loading, etc...
2. Added new command to upgrade boot code firmware without corrupting
manufacturing information.
upgfrm -b -p -f=<filename>
-b: upgrade boot code.
-p: upgrade PXE.
-f: input filename.
3. Changed command line option -m to -e to run engineering mode
4. Added command line -i for force_program_device_id option
restored option -a for setting base memory address
5. Added 5701 support
6. Added multiple card support
This version change is the same as bcmediag.exe v1.20 changes to v1.23.
Version 1.01:
1. Fixed and enabled RJ45 loopback test
The test requires to reset the system each time
replace the adapter.
Version 1.00:
1. Fixed Phy Loopback test
2. Fixed ASIC version number display
3. Disabled RJ45 loopback test
The program disables PXE and WOL by default.
To enable PXE: type q57diag -x
To enable WOL: type q57diag -w
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.