D-Link PCI Fast Ethernet Adapter Installation
NetWare Client 32 for DOS/Windows 3.1x/Windows 95
Contents
ÍÍÍÍÍÍÍÍ
Getting Started
Client 32 for Windows 95
Client 32 for DOSWIN
Getting Started
ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ
Client 32 for Windows 95
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Installing a new Auto Detect Network Card on WIN95 WITH Client 32
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
To Install NetWare 32 bit LAN Driver, in order to ensure the
INF file will be searched first by WIN95 system, please run
PUTINF32.BAT first in Windows95 DOS prompt.
PUTINF32.BAT will to do below step 1-6 procedure.
Ex. > PUTINF32.bat C:\WINDOWS ; C:\WINDOWS is Windows 95
; default directory.
1. In Windows 95, go to the \Windows\INF\ directory.
2. Remove the old NWDLKPCI.INF file (if it exists).
3. Create a temporary directory and copy all the files from the
\Windows\INF\ directory to this temporary directory.
4. Delete all the files (*.INF) in the \Windows\INF\ directory.
5. Copy the new NWDLKPCI.INF into \Windows\INF\ directory.
6. Now copy all the files back from the temporary directory you
created to the \Windows\INF\ directory.
NWDLKPCI.INF should now be the first one Windows sees in the
loading process, and be loaded before any others for the same
adapter.
Remove any adapter from the Network Control Panel for any cards
that are no longer in the system or are going to be removed,
including ODINSUP and any asscoiated files.
Shut down the system, remove the old card, install the new card,
and turn on the system.
Watch WIN95 auto-detect the hardware, and select correct new ODI
driver to be installed. If not, you may select the "Have Disk"
option for installation, in which case you will be prompted to
input the path where the driver located:
ex. A:\NETWARE\32BITLAN, if floppy disk is used.
You will then be prompted for Client 32 diskettes.
Complete the Client 32 installation.
Client 32 for DOS/Windows 3.1x
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Method 1: Install Driver During Install
Novell NetWare Client 32 for DOS/Windows 3.1x
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
In DOS environment, run "INSTALL" command.
Follow the installation steps of Novell NetWare Client 32.
In "Select a LAN Driver Type" window, select "32-bit" LAN drivers.
In "32-Bit Network Board Drivers" window, select
"USER SPECIFIED 32 BIT DRIVER".
In "Insert The Driver Disk" window, input the path
where the LAN driver and .LDI file locate:
ex. A:\NETWARE\32BITLAN, if floppy disk is used.
Select the desired parameters, eg. SLOT number....
and continue the installation procedure.
In MS Windows environment, run "SETUP" command.
In "ODI Driver Selection" window, select "32 bit" mode
and "other Boards".
Enter the path and filename of the ODI driver in "ODI Driver Path"
window.
Follow the installation setps of Novell NetWare Client 32.
After the installation, a STARTNET.BAT batch file will be created.
Please check the STARTNET.BAT file contains the right parameters.
Content of STARTNET.BAT (for 32-bit LAN driver)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
SET NWLANGUAGE=ENGLISH
C:\NOVELL\DOSCLNT\NIOS.EXE
LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
LOAD C:\NOVELL\CLIENT32\CMSM.NLM
LOAD C:\NOVELL\CLIENT32\ETHERTSM.NLM
LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_802.2 SLOT=??
LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_802.3 SLOT=??
LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_II SLOT=??
LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_SNAP SLOT=??
LOAD C:\NOVELL\CLIENT32\IPX.NLM <-- Binding driver
LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM <-- Finding server
Content of STARTNET.BAT (for 16-bit DOS driver)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
SET NWLANGUAGE=ENGLISH
C:\NOVELL\CLIENT32\NIOS.EXE
C:\NOVELL\CLIENT32\LSL.COM
C:\NOVELL\CLIENT32\N16ODI.COM
C:\NOVELL\CLIENT32\NESL.COM
C:\NOVELL\CLIENT32\DLKPCI.COM
LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
LOAD C:\NOVELL\CLIENT32\PC32MLID.LAN
LOAD C:\NOVELL\CLIENT32\TCPIP.NLM
LOAD C:\NOVELL\CLIENT32\IPX.NLM <-- Binding driver
LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM <-- Finding server
Content of NET.CFG
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Link Driver DLKPCI
Frame Ethernet_802.2
Frame Ethernet_802.3
Frame Ethernet_II
Frame Ethernet_SNAP
NetWare DOS Requester
FIRST NETWORK DRIVE = F
NETWARE PROTOCOL = NDS BIND
NOTE: You can run the NetWare client installation program for each
workstation type from the CLIENT directory under SYS:PUBLIC or
directly from the CD-ROM.
Method 2: Install Driver After Novell NetWare Client 32 for
DOS/Windows 3.1x is Installed
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Copy the LAN driver and LDI file to the \Novell\Client32 directory,
and use text editor to edit STARTNET.BAT file directly.
TroubleShooting
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
If you experience the warning messages displayed when STARTNET.BAT
is executed, "Command Line Parameter Prompt for DLKPCI" then
follow the instructions as below:
Change
LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_802.3
to
LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_802.3 SLOT=1
in STARTNET.BAT, where SLOT must be the correct value as found
by driver.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.