1. 500TX_C5.EXE Driver
2. DOSODI.TXT File Contents

DOSODI.TXT Driver File Contents (500TX_C5.EXE)

              D-Link PCI Fast Ethernet Adapter Installation
                     for NetWare DOS ODI Driver

 Contents
 ÍÍÍÍÍÍÍÍ
    Introduction
    Getting Started
        First installation from CD ROM
        Manual Installation
        How to creat Diskettes for installation
        Installation from Diskettes


 Introduction
 ÍÍÍÍÍÍÍÍÍÍÍÍ
        The ODI driver program allows you to run multiple protocol
        stacks and install up to two network adapters in a workstation.
        This ODI driver supports the Port, Node Address, Protocol and
        Frame options for creating your own NET.CFG file. For more
        information on these keywords, please refer to Novell's
        "NetWare ODI shell for DOS - NET.CFG options". This installation
        assumes that the drivers are working properly.


 Getting Started
 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ
    The NOVELL installation diskettes or CD ROM are needed to
    complete this install.

    First installation from CD ROM
    ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
         Please make sure CD ROM player work fine under DOS environment.
         Run INSTALL.BAT and press any key to accept the agreement.

          Ex. >INSTALL

         Select "Client Installation" in Select the type of installation
          desired window.

         Select "NetWare DOS/WINDOWS Client (VLM)" in Select Client to
          be installed window.

         Specify your target directory, installation default path is
          C:\NWCLIENT. (suggestion: DON'T CHANGE)

         Allow system to modified your AUTOEXEC.BAT and CONFIG.SYS.

         Specify YES to install support for MS Windows, if you accept.

         Move the highlight bar to Select the driver for your network
          board and press <Enter>.

         Put the released diskette into floppy disk and go to bottom
          Select "OTHER DRIVERS" under Network Board.

         Please insert release driver diskette into floppy disk.

         Specify the full path of ODI for DOS driver, A:\<PATH>.

          Ex. A:\

         Select "D-Link PCI" for Ethernet Adapter.

         Move to "Highlight here and press <Enter> to install".

         Press <Enter> after you configure correctly, then installation
          will copy necessary file to your hard disk.

          Restart your system and connect to NetWare server.

    Manual Installation
    ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
         Assume you have installed NetWare Client for DOS system.

         Copy <PATH>\DLKPCI.COM file from released diskette into the
          NetWare client directory containing LSL.COM, IPXODI.COM,
          NETx.COM or VLM.COM, VLM files.

          Ex. >COPY A:\DLKPCI.COM C:\NWCLIENT

         A typical Client for DOS startup batch file includes:

        Content of STARTNET.BAT
        -----------------------
        SET NWLANGUAGE=English
        C:\NWCLIENT\LSL.COM
        C:\NWCLIENT\DLKPCI.COM
        C:\NWCLIENT\IPXODI.COM
        C:\NWCLIENT\VLM.EXE
        F:                      ; According FIRST NETWORK DRIVE of
                                  NET.CFG
        LOGIN XXXX              ; Login to server, XXXX is user name

        ; Notes: C:\NWCLIENT\VLM.EXE /PS=SSSS   ; SSSS is server name


        Content of NET.CFG
        ------------------
        Link Driver DLKPCI

              FRAME ETHERNET_802.2
              FRAME ETHERNET_802.3
              FRAME ETHERNET_II
              FRAME ETHERNET_SNAP


    How to creat Diskettes for installation
    ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
         Please make sure CD ROM player work fine under DOS environment.
         Run INSTALL.BAT and press any key to accept the agreement.

          Ex. >INSTALL

         Select "Diskette Creation" in Select the type of installation
          desired window.

         Select "NetWare DOS/WINDOWS Client (VLM)" in Select the
          Diskette set to be created window.

         Following screen's instruction.

    Installation from Diskettes
    ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
         Run INSTALL program and press any key to accept the agreement.

          Ex. >INSTALL

         Please reference above "First installation from CD ROM".