CLIENT32.TXT Driver File Contents (500TX_C5.EXE)

             D-Link PCI Fast Ethernet Adapter Installation
           NetWare Client 32 for DOS/Windows 3.1x/Windows 95

 Contents
 ÍÍÍÍÍÍÍÍ
     Getting Started
       Client 32 for Windows 95
       Client 32 for DOSWIN

 Getting Started
 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ

   Client 32 for Windows 95
   ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

     Method 1:
     Installing a new Auto Detect Network Card on WIN95 WITHOUT Client 32
     ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

       If you have previously installed Novell Netware Client 32 under
       your Windows 95 system, skip this section and see
       "Method 2" below.

      Client 32 Diskette Installation:
       . Copy(Override) the NWDLKPCI.INF file to Disk 1 (setup) of the
         Client 32 for Windows 95 software.
       . Copy the new DLKPCI.LAN driver to the Client 32 LAN driver
         diskette (32-bit).
       . Add a new reference line into the "INF Files" section of
         the NWSETUP.INI file.
         Note: NWSETUP.INI can be found on Disk 1, or in the
               \NOVELL\CLIENT32\ INSTALL directory after installation.
         Sample of NWSETUP.INI file:
                 .
                 .
                 .
               [INF Files]
               1=NWClient.inf
               2=NWTrans.inf
               3=ODINSUP.inf
               4=NE3200.inf     <--- replace the line to 4=NWDLKPCI.inf
               5=NE2000.inf
               6=NE15_21.inf
               7=NE2.inf
               8=NE2_32.inf
                 .
                 .


      Shut down the system, remove the older card, add the new card,
       turn on the system.

      Remove adapters from the Network control panel for any cards that
       are no longer in the system or are going to be removed.

      In "System Settings Change" window, select "No".

      Continue to install NetWare Client 32.

      Run the Client 32 install using SETUP.EXE, check the box to
       replace NDIS with ODI.
       (The WIN95 CD will probably be required)

      In "Select Device" windows, select "D-Link" for Manufacturers,
       and select proper model for your PCI LAN adapter.

      After installation completed, reboot the machine.

      Watch WIN95 auto-detect the hardware. The correct new ODI driver
       should be installed.


     Method 2:
     Installing a new Auto Detect Network Card on WIN95 WITH Client 32
     ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

      To Install NetWare 32 bit LAN Driver, in order to ensure the
       INF file will be searched first by WIN95 system, please run
       PUTINF32.BAT first in Windows95 DOS prompt.

      PUTINF32.BAT will to do below step 1-6 procedure.

       Ex. > PUTINF32.bat C:\WINDOWS    ; C:\WINDOWS is Windows 95
                                        ; default directory.

        1. In Windows 95, go to the \Windows\INF\ directory.

        2. Remove the old NWDLKPCI.INF file (if it exists).

        3. Create a temporary directory and copy all the files from the
           \Windows\INF\ directory to this temporary directory.

        4. Delete all the files (*.INF) in the \Windows\INF\ directory.

        5. Copy the new NWDLKPCI.INF into \Windows\INF\ directory.

        6. Now copy all the files back from the temporary directory you
           created to the \Windows\INF\ directory.

      NWDLKPCI.INF should now be the first one Windows sees in the
       loading process, and be loaded before any others for the same
       adapter.

      Remove any adapter from the Network Control Panel for any cards
       that are no longer in the system or are going to be removed,
       including ODINSUP and any asscoiated files.

      Shut down the system, remove the old card, install the new card,
       and turn on the system.

      Watch WIN95 auto-detect the hardware, and select correct new ODI
       driver to be installed. If not, you may select the "Have Disk"
       option for installation, in which case you will be prompted to
       input the path where the driver located:
          ex. A:\NETWARE\32BITLAN, if floppy disk is used.

      You will then be prompted for Client 32 diskettes.

     Complete the Client 32 installation.



   Client 32 for DOS/Windows 3.1x
   ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

     Method 1: Install Driver During Install
               Novell NetWare Client 32 for DOS/Windows 3.1x
     ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

      In DOS environment, run "INSTALL" command.

      Follow the installation steps of Novell NetWare Client 32.

      In "Select a LAN Driver Type" window, select "32-bit" LAN drivers.

      In "32-Bit Network Board Drivers" window, select
       "USER SPECIFIED 32 BIT DRIVER".

      In "Insert The Driver Disk" window, input the path
       where the LAN driver and .LDI file locate:
          ex. A:\NETWARE\32BITLAN, if floppy disk is used.

      Select the desired parameters, eg. SLOT number....
       and continue the installation procedure.

      In MS Windows environment, run "SETUP" command.

      In "ODI Driver Selection" window, select "32 bit" mode
       and "other Boards".

      Enter the path and filename of the ODI driver in "ODI Driver Path"
       window.

      Follow the installation setps of Novell NetWare Client 32.

      After the installation, a STARTNET.BAT batch file will be created.
       Please check the STARTNET.BAT file contains the right parameters.

       Content of STARTNET.BAT (for 32-bit LAN driver)
       ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
       SET NWLANGUAGE=ENGLISH
       C:\NOVELL\DOSCLNT\NIOS.EXE
       LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
       LOAD C:\NOVELL\CLIENT32\CMSM.NLM
       LOAD C:\NOVELL\CLIENT32\ETHERTSM.NLM
       LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_802.2 SLOT=??
       LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_802.3 SLOT=??
       LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_II    SLOT=??
       LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_SNAP  SLOT=??
       LOAD C:\NOVELL\CLIENT32\IPX.NLM           <-- Binding driver
       LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM      <-- Finding server


       Content of STARTNET.BAT (for 16-bit DOS driver)
       ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
       SET NWLANGUAGE=ENGLISH
       C:\NOVELL\CLIENT32\NIOS.EXE
       C:\NOVELL\CLIENT32\LSL.COM
       C:\NOVELL\CLIENT32\N16ODI.COM
       C:\NOVELL\CLIENT32\NESL.COM
       C:\NOVELL\CLIENT32\DLKPCI.COM
       LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
       LOAD C:\NOVELL\CLIENT32\PC32MLID.LAN
       LOAD C:\NOVELL\CLIENT32\TCPIP.NLM
       LOAD C:\NOVELL\CLIENT32\IPX.NLM           <-- Binding driver
       LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM      <-- Finding server


       Content of NET.CFG
       ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
        Link Driver DLKPCI
                Frame Ethernet_802.2
                Frame Ethernet_802.3
                Frame Ethernet_II
                Frame Ethernet_SNAP

        NetWare DOS Requester
                FIRST NETWORK DRIVE = F
                NETWARE PROTOCOL = NDS BIND



     NOTE: You can run the NetWare client installation program for each
           workstation type from the CLIENT directory under SYS:PUBLIC or
           directly from the CD-ROM.


     Method 2: Install Driver After Novell NetWare Client 32 for
               DOS/Windows 3.1x is Installed
     ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

      Copy the LAN driver and LDI file to the \Novell\Client32 directory,
       and use text editor to edit STARTNET.BAT file directly.


     TroubleShooting
     ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

        If you experience the warning messages displayed when STARTNET.BAT
        is executed, "Command Line Parameter Prompt for DLKPCI" then
        follow the instructions as below:

         Change
          LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_802.3
          to
          LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_802.3 SLOT=1
          in STARTNET.BAT, where SLOT must be the correct value as found
          by driver.

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web5, load: 0.79