SN5000TX Fast Ethernet Adapter Installation NetWare Client 32 for DOS/Windows 3.1x/Windows 95 Contents ÍÍÍÍÍÍÍÍ Getting Started Client 32 for Windows 95 Client 32 for DOSWIN Getting Started ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Client 32 for Windows 95 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Method 1: Installing a new Auto Detect Network Card on WIN95 WITHOUT Client 32 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ If you have previously installed Novell Netware Client 32 under your Windows 95 system, skip this section and see "Method 2" below. Client 32 Diskette Installation: . Copy(Override) the SN5000.INF file to Disk 1 (setup) of the Client 32 for Windows 95 software. SN5000.INF file is loacted at A:\NETWARE\32BITLAN . Copy the new SN5000.LAN driver to the Client 32 LAN driver diskette (32-bit). . Add a new reference line into the "INF Files" section of the NWSETUP.INI file. Note: NWSETUP.INI can be found on Disk 1, or in the \NOVELL\CLIENT32\ INSTALL directory after installation. Sample of NWSETUP.INI file: . . . [INF Files] 1=NWClient.inf 2=NWTrans.inf 3=ODINSUP.inf 4=NE3200.inf <--- replace the line to 4=SN5000.inf 5=NE2000.inf 6=NE15_21.inf 7=NE2.inf 8=NE2_32.inf . . Shut down the system, remove the older card, add the new card, turn on the system. Remove adapters from the Network control panel for any cards that are no longer in the system or are going to be removed. In "System Settings Change" window, select "No". Continue to install NetWare Client 32. Run the Client 32 install using SETUP.EXE, check the box to replace NDIS with ODI. (The WIN95 CD will probably be required) In "Select Device" windows, select "AXEL" for Manufacturers, and select proper model for your PCI LAN adapter. After installation completed, reboot the machine. Watch WIN95 auto-detect the hardware. The correct new ODI driver should be installed. Method 2: Installing a new Auto Detect Network Card on WIN95 WITH Client 32 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Remove any adapter from the Network Control Panel for any cards that are no longer in the system or are going to be removed, including ODINSUP and any asscoiated files. Shut down the system, remove the old card, install the new card, and turn on the system. WIN95 will auto-detect the hardware, pop up a "New Hardware Found" dialog box with "PCI Ethernet Controller" and the select item stay at "Driver from disk provided by hardware manufacture". Now click "OK" button, a new dialog box "Install from Disk" will be popped up, then insert the driver diskette into floppy disk driver and click "OK" button. Then follow the instructions which queried by WIN95 to finish the installation. On the "System Setting Change" dialog box, click "Yes" button to restart computer. Client 32 for DOS/Windows 3.1x ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Method 1: Install Driver During Install Novell NetWare Client 32 for DOS/Windows 3.1x ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ In DOS environment, run "INSTALL" command. Follow the installation steps of Novell NetWare Client 32. In "Select a LAN Driver Type" window, select "32-bit" LAN drivers. In "32-Bit Network Board Drivers" window, select "USER SPECIFIED 32 BIT DRIVER". In "Insert The Driver Disk" window, input the path where the LAN driver and .LDI file locate: ex. A:\NETWARE\32BITLAN, if floppy disk is used. Select the desired parameters, eg. Frame Type.... and continue the installation procedure. In MS Windows environment, run "SETUP" command. In "ODI Driver Selection" window, select "32 bit" mode and "other Boards". Enter the path and filename of the ODI driver in "ODI Driver Path" window. Follow the installation setps of Novell NetWare Client 32. After the installation, a STARTNET.BAT batch file will be created. Please check the STARTNET.BAT file contains the right parameters. Content of STARTNET.BAT (for 32-bit LAN driver) ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ SET NWLANGUAGE=ENGLISH C:\NOVELL\DOSCLNT\NIOS.EXE LOAD C:\NOVELL\CLIENT32\LSLC32.NLM LOAD C:\NOVELL\CLIENT32\CMSM.NLM LOAD C:\NOVELL\CLIENT32\ETHERTSM.NLM LOAD C:\NOVELL\CLIENT32\SN5000.LAN FRAME=ETHERNET_802.2 SLOT=?? LOAD C:\NOVELL\CLIENT32\SN5000.LAN FRAME=ETHERNET_802.3 SLOT=?? LOAD C:\NOVELL\CLIENT32\SN5000.LAN FRAME=ETHERNET_II SLOT=?? LOAD C:\NOVELL\CLIENT32\SN5000.LAN FRAME=ETHERNET_SNAP SLOT=?? LOAD C:\NOVELL\CLIENT32\IPX.NLM <-- Binding driver LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM <-- Finding server Content of STARTNET.BAT (for 16-bit DOS driver) ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ SET NWLANGUAGE=ENGLISH C:\NOVELL\CLIENT32\NIOS.EXE C:\NOVELL\CLIENT32\LSL.COM C:\NOVELL\CLIENT32\N16ODI.COM C:\NOVELL\CLIENT32\NESL.COM C:\NOVELL\CLIENT32\SN5000.COM LOAD C:\NOVELL\CLIENT32\LSLC32.NLM LOAD C:\NOVELL\CLIENT32\PC32MLID.LAN LOAD C:\NOVELL\CLIENT32\TCPIP.NLM LOAD C:\NOVELL\CLIENT32\IPX.NLM <-- Binding driver LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM <-- Finding server Content of NET.CFG ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Link Driver SN5000 Frame Ethernet_802.2 Frame Ethernet_802.3 Frame Ethernet_II Frame Ethernet_SNAP NetWare DOS Requester FIRST NETWORK DRIVE = F NETWARE PROTOCOL = NDS BIND NOTE: You can run the NetWare client installation program for each workstation type from the CLIENT directory under SYS:PUBLIC or directly from the CD-ROM. Method 2: Install Driver After Novell NetWare Client 32 for DOS/Windows 3.1x is Installed ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Copy the LAN driver and LDI file to the \Novell\Client32 directory, and use text editor to edit STARTNET.BAT file directly. TroubleShooting ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ If you experience the warning messages displayed when STARTNET.BAT is executed, "Command Line Parameter Prompt for SN5000" then follow the instructions as below: Change LOAD C:\NOVELL\CLIENT32\SN5000.LAN FRAME=ETHERNET_802.3 to LOAD C:\NOVELL\CLIENT32\SN5000.LAN FRAME=ETHERNET_802.3 SLOT=1 in STARTNET.BAT, where SLOT must be the correct value as found by driver.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.