1. AGPSiS.zip Driver
2. 62010002.TXT File Contents

62010002.TXT Driver File Contents (AGPSiS.zip)

//-------------------------------------------------------------------------//

// 	                       62010002.TXT File                    	   //

//     README file for SiS620     , Version 1.00.02        	           //

// (C)Copyright Silicon Integrated Systems Corporation, 1998               //

//-------------------------------------------------------------------------//



This document describes the release notes for version 1.00.02          

of SiS620   drivers and utilities.                         









<New Feature/Major Change>



Feature list:

Formal Release for WHQL 

(1) Version Update

(2) Bug fix.

(3) Win95 & 98 drivers seperate for fix the multiple monitor bug.

(4) DCT-100 PC98#24~#29 should pass, except the "out of device scope" error.

(5) Fixed using "VerInfo" utility to view the drivers version not correct bug.



<Win2D_NT4.0>

(1) For support modes bug in Non UMA sinbad and Non UMA eagle

    project (memory clock is always 60MHz because the vga bios will

    set Sr33 D=1-- hardware issue)



<Win2D_NT5.0>:

(1) For support modes bug in Non UMA sinbad and Non UMA eagle

    project (memory clock is always 90MHz because the vga bios will

    set Sr33 D=1-- hardware issue)

(2) For the test of pc98 downloadable RAMDAC in DCT 100



<WinDDraw_NT4.0>

(1) Open Src_Blt & Dst_Blt capabilities in 32 bpp modes

(2) Modify about "check available queue length from 8-bits to 13-bits



<WinDDraw_95>

(1) Add Palette capality 

(2) Solve 3D WinBench refresh rate mismatch problem



<WinDDraw_NT5.0>

(1) Modify about "check available queue length from 8-bits to 13-bits

(2) Add primaryGamma capability



<Win95_2D>

  Bugs Fixed:

    (1) Incorrect refresh rate value sent to the DirectDraw under 

        low-resolution modes.

  Work Around:

    (1) Vertical theshold bars flashed when opening a DOS-Prompt window.

    (2) No driver version information in the property sheet of "Device 

        Manager" of "System" of the Control Panel.



<Win95_Utility>

(1) Display Modes - sissh620.dll Change version &  Re-compile-link



<Win95_3D>

(1) Fixed refresh rate problem on 3D Winbench 99

(2) Fixed texture size #2 will hangup on 3D Winbench 99

(3) Tune 3D Winbench performance



<VBIOS>

(1) Modify One Read Two Write (H/W)

(2) Modify Vesa Monitor spec.







<Bug Fixed>

================================================================================



<Title>: The page of Display mode is not the English Version.

<Description>: 1. Install VGA Driver.

               2. Click Display properties.

               3. Click Advance buttom.

               4. There is one page (Display Mode) is in French Version.

<V. Driver>: 1.00.00

<V. Chip>: 620 (Shared)

<S. BIOS>: Phoenix

<O.S.>: Win95/98

================================================================================



<Title>: File version is "Not available".

<Description>: 1.In win95, use Inf install driver then into system

               2.In display the Driver Version is Not Available

<V. Driver>: 1.00.00

<V. Chip>: 620 (Shared)

<S. BIOS>: Phoenix

<O.S.>: Win95

================================================================================



<Title>: MM test :change monitor type will hang.

<Description>: 1.)In win98, run MM test.

               2.)When sis620 as secondary adapter, and change the monitor type 

                  from "Phililis BRILLIANCE 107" to "Plus and Play Monitor", the 

                  system will hang.

               note: The another VGA adapter is S3 Trio 64V+

<V. Driver>: 1.00.01

<V. Chip>: 620 (Shared)

<S. BIOS>: Phoenix

<O.S.>: Win98

================================================================================



<Title>: After install driver by "setup", the system didn't support the "AGP".

<Description>: 1.)In win95 & win98, install the VGA driver by "setup".

               2.)The system didn't support the "AGP".

<V. Driver>: 1.00.02

<V. Chip>: 620 (Shared)

<S. BIOS>: Phoenix

<O.S.>: Win95/98

================================================================================



<Title>: The system is fail to uninstall the VGA driver.

<Description>: 1.)In win95 & win98, uninstall the VGA driver.

               2.)There will has error message: "CreateUninstallBatch-szInfName",

                  "Open Inf file error".

               3.)Restart the system, the system still own the VGA driver.

<V. Driver>: 1.00.02

<V. Chip>: 620 (Shared)

<S. BIOS>: Phoenix

<O.S.>: Win95/98

================================================================================



<Title>: File version didn't match.

<Description>: 1.)In win95 & win98, use "VerInfo" to check Dd620.dll & 

                  Dd620_32.dll version.

               2.)The "Version" is 4.10.01.1000, but the "Version String" 

                  is 4.11.01.1000

<V. Driver>: 1.00.02

<V. Chip>: 620 (Shared)

<S. BIOS>: Phoenix

<O.S.>: Win95/98

================================================================================



<Title>: Lack of the Version String.

<Description>: 1.)In win 98 VGA driver, use "VerInfo" to check "sis620v.vxd".

               2.)There will be lack of the "Version String".

               note: The version string should be "4.11.01.1000".

<V. Driver>: 1.00.02

<V. Chip>: 620 (Shared)

<S. BIOS>: Phoenix

<O.S.>: Win98

================================================================================



<Title>: (WHQL)D3D\overdraw/underdraw test is fail.

<Description>: 1.)In win95 & win98, run DCT100 test.

               2.)The D3D\overdraw/underdraw test is fail.

<V. Driver>: 1.00.02

<V. Chip>: 620 (Shared)

<S. BIOS>: Phoenix

<O.S.>: Win95/98

================================================================================