1. LG10_100_tp.zip Driver
2. lanman.txt File Contents

lanman.txt Driver File Contents (LG10_100_tp.zip)

 
                 PRO120 100/10 Mbps PCI Bus Fast Ethernet Adapter
                                 NDIS MAC Driver
              for LAN Manager Workstation/Server Installation Guide
              =====================================================


Installation Procedure
======================

 1. Introduction
 ===============
 This document describes the procedure to setup LAN Manager 2.x
 Workstation/Server driver for the PCI Fast Ethernet Adapter.

 2. Location of Driver
 =====================
 (DOS) \NDIS2\DOS\MXNICF.DOS
 (OS/2)\NDIS2\OS2\MXNICF.OS2

 3. Sample Configuration Files
 =============================
 CONFIG.SYS (for DOS will contain) 
   DEVICE=C:\LANMAN.DOS\DRIVERS\PROTMAN\PROTMAN.DOS /I:C:\LANMAN.DOS
   DEVICE=C:\LANMAN.DOS\DRIVERS\ETHERNET\MXNICF\MXNICF.DOS


 CONFIG.SYS (for OS/2 will contain)
   DEVICE=C:\LANMAN.OS2\DRIVERS\PROTMAN\PROTMAN.OS2 /I:C:\LANMAN.OS2
   DEVICE=C:\LANMAN.OS2\DRIVERS\ETHERNET\MXNICF\MXNICF.OS2

 PROTOCOL.INI (will contain)
   [MXNICF_NIF]
   ; PROTOCOL.INI SAMPLE

     DriverName = MXNICF$

   ;; Range: 0-7.
   ;; Usage: "Board=nn"
   ;------------------
   ;  Board = 0

   ;; Options: NWAY, TX10, TX10FD, TX100, TX100FD.
   ;; Usage: "MEDIA_TYPE=xxx"
   ;-------------------------
      MEDIA_TYPE = NWAY

   Note: If you request 10Mbps Full Duplex mode, please change the statement
         ;;MEDIA_TYPE=NWAY which inside PROTOCOL.INI as 
         ;;MEDIA_TYPE=TX10FD and delete its semi-colon. Please change 
	 corresponding option for another mode.


 4. NDIS Driver Installation on LAN Manager v2.1
 ===============================================
 Before you start with the installation process, make sure that the adapter is
 properly installed and configured. Besides, make sure your Microsoft LAN
 Manager is properly installed too.

  a. Run the appropriate Microsoft LAN Manager SETUP for computer you are
     setting up.(DOS, OS/2 or OS/2 Server). Select "Configuration" item since
     the adapter driver isn't included on the LAN Manager disk, insert the
     adapter driver diskette, select the item "PCI Fast Ethernet Adapters NDIS2
     MAC Driver" and follow the directions.

  b. When completed, reboot your computer.


 5. NDIS Driver Installation on LAN Manager v2.2
 ===============================================

  a. Type setup in the LAN Manager directory and press <Enter>.  The Microsoft
     LAN Manager Setup screen should appear.

  b. Choose "Network Drivers" from the "Configuration" field.  Press <Enter> to
     confirm your choice.

  c. Choose <Add New Config> and press <Enter> to display a list of Network
     Adapter Drivers.

  d. Choose <Other Driver> and press <Enter>.

  e. Insert the Driver Diskette into drive A: or B: of your PC.  Indicate the
     drive location A: or B: of the diskette and select <OK> to proceed.

  f. Select the appropriate Network Adapter Driver from the list.
     For example, select

      "PRO120 100/10 Mbps PCI Bus Fast Ethernet Adapter"

       Select <OK> to confirm your choice.

  g. Select an appropriate protocol. Use the <Space bar> to mark your choice. 
     If you have chosen the TCP/IP protocol, you will be prompted to issue the
     IP address, the subnet mask, and the default gateway (router).  By the
     default, the workstation number of NetBIOS session is set to 6.  Please 
     consult Microsoft LAN Manager Installation Manual for more detail or check
     the online help.

  h. Select <OK> to confirm your choice.  A Configuration Complete messages
     should appear on the screen.

  i. Save the configuration. Select <Save>.

  j. Press <F3> to exit.