[DESTINATIONS] ; The names of the playback and recording panels can be overwritten here. ; For example, the DESTINATION name is used as the caption on the Windows ; '95 Mixer panel. The Mixer Panel/Options/Properties Menu, selects which ; destination is displayed by the Mixer Application. VolShortName=Master Vol VolLongName=Master Volume RecShortName=Rec RecLongName=Recording Control VoiceShortName=Voice VoiceLongName=Voice Commands [SOURCES] ; Applications that refer to sources will get information on the source from ; this section. For example, this is where it would take the name and ; determine whether the SOURCE should be displayed or not. ; CDShortName=xxx ; CDDisable=0 ; The prefix of an entry ("CD" in this example) is the name that is always ; used by the driver. If the ShortName has no assignment in WPUNIMIX.INI ; CDShortName = ; an application program that displays SOURCE names would display "CD". ; If the ShortName does have an assignment in WPUNIMIX.INI. ; CDShortName=xxx ; an application program that displays SOURCE names would display "xxx". ; This section of the WPUNIMIX.INI file is also used to control whether a ; line is displayed or not. For example, if the WPUNIMIX file has an entry ; CDDisable=1 ; an application program that displays SOURCE lines would not display the ; CD line. If this line did not appear at all or if the value was set to ; zero, an application program that displays SOURCE lines would display ; the CD line. ; Lines are enabled by default. CDShortName=CD CDLongName=CD AuxShortName=Aux AuxLongName=Aux VideoShortName=Vid VideoLongName=Vid VideoDisable=1 SynthShortName=Int FM SynthLongName=Internal FM MicShortName=Mic MicLongName=Mic LineShortName=LineI LineLongName=Line In M InDisable=1 M OutDisable=1 ModemDisable=1 LOutShortName=LineO LOutLongName=Line Out I2S0ShortName=I2S0 I2S0LongName=I2S0 I2S0Disable=1 I2S1ShortName=I2S1 I2S1LongName=I2S1 I2S1Disable=1 PhatShortName=3D PhatLongName=3D Voice [CONTROLS] ; This section is used to override the default settings for each control. This ; includes all volume sliders and mute buttons, AGC, 20dB Boost and external ; controls (XC0,XC1). Controls are enabled by default. ; If an application displayed the names of CONTROL, it would take the name from ; this section. However, most applications use the name of the SOURCE. XC0Disable=1 XC1Disable=1 AGC 20dB Record Source Voice Source Master Volume Master Mute CD VolumeShortName=IntCD Aux VolumeShortName=AuxWT Video Volume Wave Volume Synth Volume Mic Out Volume Line-In Volume MonoIn VolumeDisable=1 M Out VolumeDisable=1 Modem VolumeDisable=1 I2S0 VolumeDisable=1 I2S1 Volume CD Mute Aux Mute Video Mute Voice Mute Synth Mute Mic Mute Line-In Mute MonoIn MuteDisable=1 M Out MuteDisable=1 Modem MuteDisable=1 I2S0 MuteDisable=1 I2S1 Mute [SETTINGS] ; This is where the values of all sliders and buttons are set (including ; treble, bass, AGC, 20dB, XC0, XC1). Also the default input lines for ; the record panels can be selected. Furthermore some hardware settings ; are configured here: HW volume, I2S format, Vendor ID. ; These are binary settings. 0 = FALSE, any other number = TRUE DACMute=0 ; Wave output MicMute=1 LineInMute=1 CDMute=0 AuxMute=1 VidMute=1 MonoInMute=1 ModemMute=1 I2S0Mute=1 I2S1Mute=1 WaveMicAGC=0 VoiceMicAGC=0 Mic20dB=1 XCTL0=0 XCTL1=0 MonoOutMute=0 FMMute=0 3DOn=1 HwVolume=0 ; Show control on property page = 1, don't show = 0 EnableHwVol=0 ; Default HwVolume enable setting (1=enable, 0 = disable) CalibrateVolume=0 ; Show Calibration buttons = 1 ;These are volume settings. 0 to 65535 decimal WaveInAux1=32767 WaveInAux2=32767 WaveInAux3=32767 WaveInLine=32767 WaveInLOut=32767 WaveInMic=32767 WaveInModem=32767 VoiceInAux1=32767 VoiceInAux2=32767 VoiceInAux3=32767 VoiceInLine=32767 VoiceInLOut=32767 VoiceInMic=32767 VoiceInModem=32767 DACVol=32767 ; Wave output FMSynthVol=32767 LineInVol=32767 MicVol=0 CDVol=10000 AuxVol=10000 VidVol=0 I2S0Vol=0 I2S1Vol=0 MonoInVol=0 ModemVol=0 3DLevel=50000 MonoOutVol=0 MasterVol=32767 Bass=32767 Treble=32767 I2S0Format=1 ;0=Off, 1=Right justified, 2=I2S justified, 3=Left justified I2S1Format=1 HwVolMin=12 ; Default settings for Hardware volume Min and Max HwVolMax=72 ; ; Set default Capture source ; Line, LOut, CD, Mic, Aux, Video WaveInSource=Mic VoiceInSource=Mic ; New settings for release 4.05.00.0156 and greater ; ;Set the PnP VendorID (used with AD1816/7(A) with external eeprom and VendorID ; different than ADS7180). This is used by the remove program. ; ;Note: you can specify multiple ID's on this line ; (e.g. VendorID=ADS7180,ADS7181,OEM1234 ; ; use for Vendor ID. Replace OEMxxxx with your PnP Vendor ID ;VendorID=OEMxxxx ; ; use for AD1817A ;VendorID=ADS7191 ; New settings for release 4.05.00.0158 and greater ; ;Set the Vendor String. This is displayed in various locations such as the ; Mixer applet, ControlPanel/MultiMedia/Audio (Playback and Record devices), ; and the remove tool. ; The default setting is "ADI Sound Controller" ; ; for legacy compatibility VendorStr=AD1815/6 ; ; use for AD1817A ;VendorStr=AD1817 ;disable display of property sheet controls. For compatibility with ; old driver releases the default is to display the controls. ; 0 = do not display control ; 1 = display the control (default) ShowSingleDMA=1 ; Single Mode DMA ShowDigitalCD=1 ; CheckBox for enableing Digital CD input on I2S0 ShowCNP=1 ; Capture not equal to playback Show3D=1 ; Enable 3D digital ShowI2S0=1 ; I2S format ShowI2S1=1 ShowClkMul=1 ; Clock multiplier ShowTypeF=1 ; Type F DMA usage ; Default settings for property sheet settings. EnableSingleDMA=0 ; driver default is FALSE if not specified here EnableDigitalCD=0 ; driver default is FALSE if not specified here EnableDigital3D=1 ; Apply Phat Stereo to analog and digital signals CNP=1 ; Capture rate not locked to playback rate ClkMult=15 ; Clock multiplierDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.