6/14/00- Appian Graphics Jeronimo 2000 Readme information for Windows 98 CONTENTS ================================================================ 1) How to Contact Appian 2) How to Install Jeronimo 2000 Windows 98 Drivers 3) How to Install Multiple Jeronimo 2000 Cards 4) How to Uninstall Jeronimo 2000 Windows 98 Drivers 5) International Support 6) HydraVision 98 Desktop Management Support 7) Legal Information 1) How to Contact Appian ================================================================ Appian Technical Support may be reached at 1-800-422-7369 or by email at support@appian.com. Appian Sales may be reached at 1-800-727-7426. Appian is available on the Web at http://www.appian.com 2) How to Install Jeronimo 2000 Windows 98 Drivers ================================================================ These installation instructions are for Jeronimo 2000 Windows 98 drivers only. HydraVision 98 multiple monitor desktop management software is available separately from Appian Graphics for Windows 98 and can be downloaded from the Appian web site. Installation instructions for the Jeronimo 2000 PCI and AGP versions are shown separately. To install multiple Jeronimo 2000 cards and drivers, see section 3 below. NOTE: If you downloaded the Jeronimo 2000 driver package from the internet, unzip the downloaded file to a temporary subdirectory on your hard drive. Appian recommends unzipping files to your hard drive rather than to floppy disks as the driver files may be larger than the 1.44 MB capacity of a single diskette. The subdirectory you create on your hard drive should be empty of all files prior to unzipping the Jeronimo 2000 driver files. This temporary subdirectory can be deleted after driver installation. To install the Jeronimo 2000 PCI Windows 98 drivers, perform the following steps: a) Upon boot up of the system, the Add New Hardware Wizard will appear. A generic "Standard PCI Graphics Adapter (VGA)" device has been detected. Click NEXT. b) Select the "Display a list of all drivers..." option and click NEXT. c) Click HAVE DISK. Select the path to the Windows 98 driver files using the BROWSE button. d) Click OK. The Select Device dialog box appears with the Jeronimo 2000 Windows 98 driver selected. e) Click OK. You are returned to the Add New Hardware Wizard and informed that Windows is ready to install the Jeronimo 2000 driver. f) Click NEXT. A dialog box appears informing you that the driver files are being copied. A message then appears, confirming successful installation. g) Click FINISH. h) You are prompted to restart the system. Click YES. i) Because there are multiple graphics processors on the Jeronimo 2000, the Add New Hardware Wizard will appear upon reboot of the system. The "Appian J2000 Win98" device has been detected. Click NEXT. j) Select the "Search for the best driver..." option and click NEXT. k) Click NEXT, click NEXT again, then click FINISH. l) You are prompted to restart the system. Click YES. m) Upon reboot of the system, the Add New Hardware Wizard will appear. A "PCI Multimedia Video" device has been detected. Click NEXT. n) Select the "Search for the best driver..." option and click NEXT. o) Click NEXT, click NEXT again, then click FINISH. p) The Add New Hardware Wizard will appear. A "PCI Multimedia" device has been detected. Click NEXT. q) Select the "Search for the best driver..." option and click NEXT. r) Click NEXT, click NEXT again, then click FINISH. s) Windows 98 now restarts in 640x480 single monitor mode. You can change this and other settings using the Display Properties dialog box. To install the Jeronimo 2000 AGP Windows 98 drivers, perform the following steps: a) Upon boot up of the system, the Add New Hardware Wizard will appear. A generic "PCI Coprocessor CPU" device has been detected. Click NEXT. b) Select the "Search for the best driver..." option and click NEXT. c) Click NEXT, click NEXT again, then click FINISH. d) The Add New Hardware Wizard will appear. A "Standard PCI Graphics Adapter (VGA)" device has been detected. Click NEXT. e) Select the "Display a list of all drivers..." option and click NEXT. f) Click HAVE DISK. Select the path to the Windows 98 driver files using the BROWSE button. g) Click NEXT, then click FINISH. h) The "Appian J2000 Win98" device has been detected. Click NEXT. Windows installs the driver. i) You are prompted to restart the system. Click YES. j) Windows 98 now restarts in 640x480 single monitor mode. You can change this and other settings using the Display Properties dialog box. 3) How to Install Multiple Jeronimo 2000 Cards ================================================================ When using multiple Jeronimo 2000 cards in a single system, Appian recommends installing each card separately. To install multiple Jeronimo 2000 cards, perform the following steps: a) Complete the hardware installation for a single Jeronimo 2000 card, using the instructions in the Jeronimo 2000 User's Guide. b) Boot up the system. c) Install the Jeronimo 2000 Windows 98 driver files, using the instructions in the Jeronimo 2000 User's Guide. d) Verify that the system is operating properly. e) Shut down the system and turn the power off. f) Repeat steps a) through e) for each remaining Jeronimo 2000 card. g) When the last Jeronimo 2000 card and driver has been installed, boot up the system and verify that all monitors are detected and available. 4) How to Uninstall Jeronimo 2000 Windows 98 Drivers ================================================================ To uninstall Jeronimo 2000 drivers in Windows 98, use the Windows Add/Remove programs control panel utility. 5) International Support ================================================================ HydraVision 98 provides support for Brazilian Portuguese, Danish, Dutch, Finnish, French, German, Italian, Japanese, Korean, Norwegian, Spanish, Swedish, Simplified Chinese and Traditional Chinese. If you are running Windows 98 in any of these languages, HydraVision 98 will automatically load the appropriate localized Control Panel. If you are running Windows 98 in a non-supported language, the HydraVision 98 Control Panel will be available in English only. 6) HydraVision 98 Desktop Management Support ================================================================ In Windows 98, Appian HydraVision desktop management software is installed separately from the Jeronimo 2000 driver. HydraVision software for both Windows 98 and Windows 2000 is called HydraVision 98. To install HydraVision 98, please download the software from the Appian Graphics FTP site at http://ftp.appian.com or refer to the Jeronimo 2000 CD-ROM or diskettes and install per the instructions in that package. 7) Legal Information ================================================================ This material is made available for use under a license from Appian Graphics and its use is subject to all conditions and restrictions provided by the license agreement. Appian software programs and Appian hardware devices are covered by one or more of the following U.S. patents: 5,835,090 5,848,294 5,949,437 Additional patents are pending.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.