ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ACCTON TECHNOLOGY CORPORATION ³ ³ EtherDuo-PCI NETWORK TESTING PROGRAM (ACCTEST) USER GUIDE ³ ³ ³ ³ Copyright 1992-1995 ACCTON Technology Corporation ³ ³ All rights reserved. ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º Release History º ÌÍÍÍÍÍÍÍÍÍÍÍÍËÍÍÍÍÍÍÍÍÍËÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹ º date º version º description º ÌÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹ º 02-18-1994 º v1.00 º 1. New release. º º º º º º 11-12-1994 º v1.03 º 1. Support multiple adapters. º º º º 2. Modify the medium selection method.º º º º º º 01-09-1995 º v1.04 º 1. Support medium auto-sense function.º º º º 2. Reset NIC before each functional º º º º testing. º º º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÊÍÍÍÍÍÍÍÍÍÊÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ 1. The ACCTON EtherDuo-PCI Network Testing Program - ACCTEST The ACCTON Hardware Driver Disk includes a network testing program called ACCTEST. Run this program to check if your adapter is properly installed. The ACCTEST program works for the following EtherDuo-PCI LAN adapters: ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Product Name Product Number ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ EtherDuo-PCI EN1203 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ This ACCTEST program performs the following tests on your adapter : a. Configuration Test b. I/O Test c. ID Test d. Internal Loopback Test e. External Loopback Test f. Interrupt Test g. Network Function Test 2. Test Requirements To run ACCTEST, you need at least two workstations, each with an installed EtherDuo_PCI or any ACCTON Ethernet adapter. You should run the program in both workstations, one after the other. 3. Running the ACCTEST Program Insert the ACCTON EtherDuo_PCI Hardware Driver Disk into drive A:, then type: A:\> ACCTEST <Enter> ------------------------------------------------------------------- 3.0. As you enter ACCTEST program, the program first finds all the EtherDuo PCI adapters on your PC. If your PC dose not support PCI BIOS, or there is no EtherDuo PCI adapter on your PC, then the program will show you an error message. Otherwise, ACCTEST will display information of all the adapters (at most 4) on your PCI machine. Each adapter information is consisted of adapter no., IRQ used, I/O port used, and a predefined medium type (AUTO, means medium AUTO-sense). You can use UP, DOWN arrow keys to select the adapter for testing, or use RIGHT, LEFT arrow keys to select medium type from AUTO, TP or BNC. Notice, AUI port is not supported for this version of EN-1203 adapter. Finally, you must press ENTER to confirm your selection for entering the test procedure, or press ESC to exit the ACCTEST program. 3.1. After you selected an adapter, then Testing Report showing the result of each test conducted appears on your screen. The test results are indicated by a 'PASS' or 'FAIL' remark. The screen display on your monitor is like Figure 1. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ11:51:55 AM º EtherDuo-PCI Network Testing Program º º Ver 1.04 01-09-95 Copyright (C) ACCTON Technology Corp. 1992 - 1995 º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °ÉÍÍÍ Testing Report ÍÍÍÍÍÍÍÍÍÍÍ»°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °º Adapter #0 IRQ: 9 Port:D000 º°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °ÇÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĶ°°°°° W E L C O M E T O °°°°°°°°°°°°°°°°°°° °º Configuration test : PASS º°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °º I/O test : PASS º°°°°ÝÝ°°°°°ÝÝÝÝ°°°ÝÝÝÝ°°ÝÝÝÝÝÝ°°ÝÝÝÝ°°ÝÝ°°°ÝÝ°° °º ID test : PASS º°°°ÝÝÝÝ°°°ÝÝ°°ÝÝ°ÝÝ°°ÝÝ°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝÝ°°ÝÝ°° °º Internal Loopback Test: PASS º°°ÝÝ°°ÝÝ°°ÝÝ°°°°°ÝÝ°°°°°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝÝÝ°ÝÝ°° °º External Loopback Test: PASS º°°ÝÝ°°ÝÝ°°ÝÝ°°°°°ÝÝ°°°°°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝ°ÝÝÝÝ°° °º Interrupt test : _ º°°ÝÝÝÝÝÝ°°ÝÝ°°ÝÝ°ÝÝ°°ÝÝ°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝ°°ÝÝÝ°° °º º°ÝÝÝ°°ÝÝÝ°°ÝÝÝÝ°°°ÝÝÝÝ°°°°ÝÝ°°°°ÝÝÝÝ°°ÝÝ°°°ÝÝ°° °ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ°ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ°° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° ESC to Exit 3.2 Figure 1 - EtherDuo-PCI Test Screen This screen will present you with a Testing Report to indicate the result of each test conducted. The test results will be indicated by a 'PASS' or 'FAIL' remark. When the network function test is running, the EtherDuo-PCI Test Screen layout given in Figure 2 will be shown on your screen. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ11:51:55 AM º EtherDuo-PCI Network Testing Program º º Ver 1.04 01-09-95 Copyright (C) ACCTON Technology Corp. 1992 - 1995 º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °ÉÍÍÍ Testing Report ÍÍÍÍÍÍÍÍÍÍÍ»°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °º Adapter #0 IRQ: 9 Port:D000 º°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °ÇÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĶ°°°°° W E L C O M E T O °°°°°°°°°°°°°°°°°°° °º Configuration test : PASS º°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °º I/O test : PASS º°°°°ÝÝ°°°°°ÝÝÝÝ°°°ÝÝÝÝ°°ÝÝÝÝÝÝ°°ÝÝÝÝ°°ÝÝ°°°ÝÝ°° °º ID test : PASS º°°°ÝÝÝÝ°°°ÝÝ°°ÝÝ°ÝÝ°°ÝÝ°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝÝ°°ÝÝ°° °º Internal Loopback Test: PASS º°°ÝÝ°°ÝÝ°°ÝÝ°°°°°ÝÝ°°°°°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝÝÝ°ÝÝ°° °º External Loopback Test: PASS º°°ÝÝ°°ÝÝ°°ÝÝ°°°°°ÝÝ°°°°°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝ°ÝÝÝÝ°° °º Interrupt test : PASS º°°ÝÝÝÝÝÝ°°ÝÝ°°ÝÝ°ÝÝ°°ÝÝ°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝ°°ÝÝÝ°° °º Network Function Test : ON º°ÝÝÝ°°ÝÝÝ°°ÝÝÝÝ°°°ÝÝÝÝ°°°°ÝÝ°°°°ÝÝÝÝ°°ÝÝ°°°ÝÝ°° °ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ°ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ°° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Node ID: [ xx xx xx xx xx xx ] ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º Tx Count : 0 Packets Rx Count : 0 Packets º º CRC Error : 0 º º ALG Error : 0 º º COLLISION : 0 º º Time : 0 Seconds Performance: 0.000e+000 BPS º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Press <F1> to Reset Counters, <F2> to Toggle ON/OFF, <ESC> to Exit Figure 2 - EtherDuo-PCI Test Screen with Network Function Test Running There are three functional keys which could be used during execute ACCTEST.EXE program, they are <F1> To reset all counters which report the real network status. <F2> To toggle the network function test ON or OFF. It is a toggle switch makes the network function test to be in reversed way. <ESC> To terminate and return to the Board-Selection menu. The real network status report on this ACCTEST.EXE program including TX count, RX count and two errors CRC and ALG are shown on the Test Screen. The Time that is accumulated by this program and the Performance which is calculated by this program are also shown on the Test Screen. After you press the <F2> key once, the network function test now is entering into the 'ON' condition, that is, TX count is going to increase quickly (single station). And if there is more than one station are running DIAG with network function test 'ON' on your network system (multiple stations), then RX count is also increasing quickly to reflect the real network traffic. The Test Screen layout given in Figure 3 will be shown on your screen while there is only one station running ACCTEST program. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ11:51:55 AM º EtherDuo-PCI Network Testing Program º º Ver 1.04 01-09-95 Copyright (C) ACCTON Technology Corp. 1992 - 1995 º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °ÉÍÍÍ Testing Report ÍÍÍÍÍÍÍÍÍÍÍ»°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °º Adapter #0 IRQ: 9 Port:D000 º°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °ÇÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĶ°°°°° W E L C O M E T O °°°°°°°°°°°°°°°°°°° °º Configuration test : PASS º°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °º I/O test : PASS º°°°°ÝÝ°°°°°ÝÝÝÝ°°°ÝÝÝÝ°°ÝÝÝÝÝÝ°°ÝÝÝÝ°°ÝÝ°°°ÝÝ°° °º ID test : PASS º°°°ÝÝÝÝ°°°ÝÝ°°ÝÝ°ÝÝ°°ÝÝ°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝÝ°°ÝÝ°° °º Internal Loopback Test: PASS º°°ÝÝ°°ÝÝ°°ÝÝ°°°°°ÝÝ°°°°°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝÝÝ°ÝÝ°° °º External Loopback Test: PASS º°°ÝÝ°°ÝÝ°°ÝÝ°°°°°ÝÝ°°°°°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝ°ÝÝÝÝ°° °º Interrupt test : PASS º°°ÝÝÝÝÝÝ°°ÝÝ°°ÝÝ°ÝÝ°°ÝÝ°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝ°°ÝÝÝ°° °º Network Function Test : ON º°ÝÝÝ°°ÝÝÝ°°ÝÝÝÝ°°°ÝÝÝÝ°°°°ÝÝ°°°°ÝÝÝÝ°°ÝÝ°°°ÝÝ°° °ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ°ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ°° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Node ID: [ xx xx xx xx xx xx ] ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º Tx Count : 68 Packets Rx Count : 0 Packets º º CRC Error : 0 º º ALG Error : 0 º º COLLISION : 0 º º Time : 5 Seconds Performance: 1.114e+005 BPS º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Press <F1> to Reset Counters, <F2> to Toggle ON/OFF, <ESC> to Exit Figure 3 - Test Screen with Network Function Test 'ON' (Single Station) When any of a diagnosis test results to a 'FAIL' remark, your screen will change to give you a description of the malfunction and at the same time also give you some advices to solve that problem. Figure 4 presents a layout of this screen. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ11:51:55 AM º EtherDuo-PCI Network Testing Program º º Ver 1.04 01-09-95 Copyright (C) ACCTON Technology Corp. 1992 - 1995 º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °ÉÍÍÍ Testing Report ÍÍÍÍÍÍÍÍÍÍÍ»°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °º Adapter #0 IRQ: 9 Port:D000 º°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °ÇÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĶ°°°°° W E L C O M E T O °°°°°°°°°°°°°°°°°°° °º Configuration test : PASS º°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °º I/O test : PASS º°°°°ÝÝ°°°°°ÝÝÝÝ°°°ÝÝÝÝ°°ÝÝÝÝÝÝ°°ÝÝÝÝ°°ÝÝ°°°ÝÝ°° °º ID test : PASS º°°°ÝÝÝÝ°°°ÝÝ°°ÝÝ°ÝÝ°°ÝÝ°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝÝ°°ÝÝ°° °º Internal Loopback Test: PASS º°°ÝÝ°°ÝÝ°°ÝÝ°°°°°ÝÝ°°°°°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝÝÝ°ÝÝ°° °º External Loopback Test: PASS º°°ÝÝ°°ÝÝ°°ÝÝ°°°°°ÝÝ°°°°°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝ°ÝÝÝÝ°° °º Interrupt test : FAIL º°°ÝÝÝÝÝÝ°°ÝÝ°°ÝÝ°ÝÝ°°ÝÝ°°°ÝÝ°°°ÝÝ°°ÝÝ°ÝÝ°°ÝÝÝ°° °º º°ÝÝÝ°°ÝÝÝ°°ÝÝÝÝ°°°ÝÝÝÝ°°°°ÝÝ°°°°ÝÝÝÝ°°ÝÝ°°°ÝÝ°° °ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ°ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ°° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °°ÉÍÍÍÍÍÍÍÍÍÍ Description : ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»°° °°º Please check your IRQ setting in PCI configuration, check if IRQ º°° °°º number is conflict with other adapters. And run ACCTEST.EXE again. º°° °°º Please also check the cabling system if it is connected correctly. º°° °°º If all the IRQ setting is OK and cabling system is correct too, º°° °°º contact your dealer or ACCTON Technology Corporation. º°° °°ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ°° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° ESC to Exit Figure 4 - EtherDuo-PCI Test Screen when Testing Report Results to 'FAIL' Remarks 4. Test Fail Messages Possible results and suggested solutions for the diagnostics test are listed below : ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍËÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º Test Result º Suggested Solution º ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹ º Configuration º 1. Check PCI BIOS setup about PCI º º Test Fail º adpter . º º º 2. Contact your dealer or ACCTON º º º Technology Corporation. º ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹ º I/O Test Fail º 1. Check the parameter with PCI º º º adapter in BIOS setup is correctº º º or not. º º º 2. Check if you are now running º º º EMM386.EXE. If your EMM386.EXE º º º has a version less than 4.49, º º º it can not handle properly º º º DWORD accesses and may cause º º º the I/O Test to fail. º º º 3. Contact your dealer or ACCTON º º º Technology Corporation. º ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹ º ID Test Fail º 1. ID checksum error. º º º 2. Contact your dealer or ACCTON º º º Technology Corporation º ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹ º Internal Loopback º 1. Contact your dealer or ACCTON º º Test Fail º Technology Corporation. º ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹ º External Loopback º 1. Check your cables, connectors º º Test Fail º and terminators(Coaxial cables).º º º 2. Check if you have selected the º º º right medium type. º º º 3. Contact your dealer or ACCTON º º º Technology Corporation. º ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹ º Interrupt Test º 1. Check IRQ setting in your PCI º º Fail º configuration of your computer. º º º 2. Check your cables, connectors º º º and terminators(Coaxial cables).º º º 3. Check your BIOS configuration º º º Setting, re-setup your º º º Adapter. º º º 4. Contact your dealer or ACCTON º º º Technology Corporation. º ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹ º Network Function º º º Test : º º º Receive Test Fail º 1. Check cables, connectors, and º º (Rx packet count º board connections. º º not running) º 2. Re-install the adapter board. º º º 3. Reset the stations and run the º º º ACCTEST program in various º º º sequence to decide which º º º adapter board is defective. º º º 4. Contact your dealer or ACCTON º º º Technology Corporation º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÊÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ - END -Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.