1. 2x16_v200.zip Driver
2. LANMAN.TXT File Contents

LANMAN.TXT Driver File Contents (2x16_v200.zip)

		      Accton Technology Corporation
                     EN2216/2316 PCMCIA Ethernet Adapter 
                  NDIS Driver for LAN Manager Installation
     

The driver ETHPCM.DOS contained under directory \MSLANMAN.DOS
conforms to the Network Driver Interface Specification
(NDIS) 2.0 defined by Microsoft/3Com.



1. Installation Procedure for LAN Manager V2.0
--------------------------------------------------

 a. Type "Setup" in the Lan Manager Directory.  Press <Enter>.

 b. Press <Enter>.

 c. Select "Import Network Drivers..." in "Action".  Press <Enter>.

 d. Type the source drive letter (A: or B:).

 e. Insert Driver Disk in the source drive.  Press <Enter>.
    "Import Network Drivers" appears.

 f. Press the <SPACEBAR> to select Network Adapter Card, "Accton EN2216/2316
    Adapter Card".  Press <Enter>.

 g. Press the <NO> button.

 h. Press <Enter> three times.	"Network Driver" appears.

 i. Select "Accton EN2216/2316 Ethernet Card" in the "Network Adapter Cards"
    menu.  Press <Add driver>, <Add protocol>, and <OK>.
    "Workstation Primary parameters" appears.  Press <OK>.

 k. Press <OK> three times.

 l. Select "Save" in "Action".

 m. Press <F3> to Exit.

*******************************************************************************



2. Installation Introduction for LAN Manager V2.1
--------------------------------------------------

 a. Type "lmsetup" in the Lan Manager Directory.  Press Enter.
    Microsoft LAN Manger Setup appears.

 b. Select "Network Drivers..." in "Configuration".  Press Enter.

 c. Select <Add New Configs>.  Press Enter.
    "Network Adapter Driver" appears.

 d. Select <Other Driver>.  Press Enter.

 e. Insert the Driver Disk in the source drive.  Type the
    drive letter (A: or B:).  Push the <OK> button.

 f. In "Available Network Adapter Driver", select "Accton EN2216/2316 Ethernet
    adapter".  Push the <OK> button.

 g. Press the SPACEBAR to select the protocols.

 h. Push the <OK> button.  "Configuration Complete" appears.

 i. Push the <Save> button.

 j. Press "F3" to exit.

 k. Press Enter.


Sample configuration files:

3. Config.sys

   a. <V2.0>
      LASTDRIVE=Z
      BUFFERS = 35
      FILES = 35
      SHELL=C:\DOS50\COMMAND.COM C:\DOS50\e:1000 /p /E:1024
      DEVICE=C:\HIMEM.SYS
      DEVICE=C:\DOS50\SETVER.EXE
      DOS=HIGH,UMB

      DEVICE=C:\LANMAN.DOS\DRIVERS\PROTMAN\PROTMAN.DOS /i:C:\LANMAN.DOS
      DEVICE=C:\LANMAN.DOS\DRIVERS\ACCTON\ACCNE\ETHPCM.DOS
      DEVICE=C:\LANMAN.DOS\DRIVERS\PROTOCOL\NETBEUI\NETBEUI.DOS


    b.<V2.1>
      LASTDRIVE=Z
      BUFFERS = 35
      FILES = 35
      SHELL=C:\DOS50\COMMAND.COM C:\DOS50\e:1000 /p /E:1024
      DEVICE=C:\HIMEM.SYS
      DEVICE=C:\LANMAN.DOS\DRIVERS\DOSUTILS\EMM386.EXE NoEMS
      DEVICE=C:\DOS50\SETVER.EXE
      DOS=HIGH,UMB

      DEVICE=C:\LANMAN.DOS\DRIVERS\PROTMAN\PROTMAN.DOS /i:C:\LANMAN.DOS
      DEVICE=C:\LANMAN.DOS\DRIVERS\ACCTON\ACCNE\ETHPCM.DOS


4. Protocol.ini file for LAN Manager.

  a. V2.0
       [PROTOCOL MANAGER]
	DRIVERNAME = PROTMAN$

       [NETBEUI_XIF]
	Drivername = netbeui$
	BINDINGS = "ACCNE_NIF"

       [ACCNE_NIF]
       ; PROTOCOL.INI for Accton EN2216/2316 ethernet adapter

	  drivername = ETHPCM$
	  irq = 5
	  iobase = 0x300

       ; End of this sample file



   b. V2.1
       [PROTMAN]
	DRIVERNAME = PROTMAN$
	DYNAMIC = YES
	PRIORITY = NETBEUI

       [NETBEUI_XIF]
	Drivername = netbeui$
	SESSIONS = 6
	NCBS = 12
	BINDINGS = "ACCNE_NIF"
	LANABASE = 0

       [ACCNE_NIF]
       ; PROTOCOL.INI for Accton EN2216/2316 ethernet adapter

	  drivername = ETHPCM$
	  irq = 5
	  iobase = 0x300

       ; End of this sample file



5. Autoexec.bat file for LAN Manager.

   a. V2.0

   @echo off
   PROMPT $P$G
   PATH=c:\PE2;C:\DOS50;C:\NC;
   APPEND=C:\PE2;C:\DOS50;
   REM ====== LANMAN 2.0 === DO NOT MODIFY BETWEEN THESE LINES ===== LANMAN 2.0 ====
   SET PATH=C:\LANMAN.DOS\NETPROG;%PATH%
   C:\LANMAN.DOS\DRIVERS\PROTMAN\NETBIND
   NET START WORKSTATION
   REM ====== LANMAN 2.0 === DO NOT MODIFY BETWEEN THESE LINES ===== LANMAN 2.0 ====

   b. V2.1
   @echo off
   PROMPT $P$G
   PATH=c:\PE2;C:\DOS50;C:\NC;
   APPEND=C:\PE2;C:\DOS50;

   @REM ====== LANMAN 2.1 === DO NOT MODIFY BETWEEN THESE LINES === LANMAN 2.1 ===
   SET PATH=C:\LANMAN.DOS\NETPROG;%PATH%
   NET START WORKSTATION
   LOAD NETBEUI
   @REM ====== LANMAN 2.1 === DO NOT MODIFY BETWEEN THESE LINES === LANMAN 2.1 ===