Accton Technology Corporation
EN2216/2316 PCMCIA Ethernet Adapter
NetWare Client 32 Driver for MS-DOS
Installation Procedure of Client 32 with MS-DOS
------------------------------------------------------------------------
1. From the Novell NetWare Client 32 software, run INSTALL.EXE.
2. Select the NetWare Client 32 products you want to install from the list:
[X] NetWare Client 32 for DOS
[X] NetWare Client 32 for Windows
[ ] NetWare TCP/IP protocol stack[ ] NetWare IP (TCP/IP Required)
[ ] Desktop SNMP
[ ] HOSTMIB for SNMP (SNMP Required)
[ ] NetWare TSA for SMS
Note - "NetWare Client 32 for DOS" and "NetWare Client 32 for
Windows" are usually selected by default.
3. From the Customize Support for Windows menu, specify if you want to
use multiple country codes or if you want to set the shared Windows
path. The default for both of these is NO.
4. From the Select LAN Driver Type menu, select "32-bit LAN drivers".
Copy ACCPCM.LAN and ACCPCM.LDI onto a disk.
In the Novell installation process, select "USER SPECIFIED 32 BIT DRIVER."
5. From the Insert the Driver Disk menu, insert the disk with the
ACCPCM.lan and ACCPCM.ldi files, and then specify the path to those
files.
6. From the Installation Configuration Summary, verify the default
settings for Client 32 are correct, or modify as necessary.
Modify AUTOEXEC.BAT and CONFIG.SYS [YES]
Client Directory: C:\NOVELL\CLIENT32
Windows Directory: C:\WINDOWS
LAN driver type: 32-bit LAN drivers
LAN driver: Accton EN2216/2316 PCMCIA Adapters
7. Novell NetWare will now copy the files to your workstations and
modify the configuration files to match your selected configuration.
Hints and Tips
--------------
1. Check for a LASTDRIVE statement in the CONFIG.SYS file. You must have
LASTDRIVE=Z in config.sys when using Client 32.
2. Verify that you have FIRST NETWORK DRIVE = <SOME DRIVER LETTER LESS THAN z>
in the NET.CFG file under the NetWare DOS Requester section.
NOTE: NET.CFG is position sensitive, so be careful to indent lines
with TWO spaceS or one tab as shown above in the example.
3. You must run ACCOPEN.EXE to enable the Accton EN2216/2316 PCMCIA adapter
before running the client 32 driver. Please check the following sample
STARTNET.BAT file on how to execute ACCOPEN.EXE.
Sample Configurations
---------------------
Below are sample files from a Novell NetWare Client 32 workstation with an
Accton EN2216/2316 PCMCIA adapter installed using the default installation:
CONFIG.SYS
----------
DEVICE=C:\WINDOWS\HIMEM.SYS
DECICE=C:\WINDOWS\EMM386.EXE NOEMS X=D000-DFFF
DOS=HIGH,UMB
BUFFERS=30,0
FILES=60
LASTDRIVE=Z
DEVICEHIGH=C:\CARDSOFT\SSSIS.EXE /SKT:2
DEVICEHIGH=C:\CARDSOFT\CS.EXE
DEVICEHIGH=C:\CARDSOFT\CSALLOC.EXE
AUTOEXEC.BAT
------------
prompt $P$G
path=C:\WINDOWS;C:\DOS;C:\NOVELL\CLIENT32\
SET TEMP=C:\TEMP
@CALL C:\NOVELL\CLIENT32\STARTNET
STARTNET.BAT
------------
C:\ACCOPEN.EXE <------------added by user
SET NWLANGUAGE=ENGLISH
C:\NOVELL\CLIENT32\NIOS.EXE
LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
LOAD C:\NOVELL\CLIENT32\CMSM.NLM
LOAD C:\NOVELL\CLIENT32\ETHERTSM.NLM
LOAD C:\NOVELL\CLIENT32\ACCPCM.LAN int=5 port=300 FRAME=ETHERNET_802.2 PCMCIA
LOAD C:\NOVELL\CLIENT32\ACCPCM.LAN int=5 port=300 FRAME=Ethernet_802.3 PCMCIA
LOAD C:\NOVELL\CLIENT32\ACCPCM.LAN int=5 port=300 FRAME=Ethernet_II PCMCIA
LOAD C:\NOVELL\CLIENT32\ACCPCM.LAN int=5 port=300 FRAME=Ethernet_SNAP PCMCIA
LOAD C:\NOVELL\CLIENT32\IPX.NLM
LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM
NOTE: You must run ACCOPEN.EXE to enable Accton EN2216/2316 PCMCIA adapter, ACCOPEN.EXE will display the Interrupt number
and IO port. When Client32 startup it may prompt to let you input the IO port and interrupt number, be sure to input the
IO port and interrupt number that ACCOPEN.EXE reported.
For example, when run ACCOPEN.EXE it will display:
ACCTON PCMCIA Client Driver Ver. 2.00 º
*Intel PCIC compatible controller found.
PCMCIA Card is enabled OK !
Interrupt number 0x5 (5)
I/O port 0x300 (768)
NET.CFG
-------
NetWare DOS Requester
FIRST NETWORK DRIVE F
NETWARE PROTOCOL NDS BIND
Protocol IPX
IPX SOCKETS 40
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.