1. 510_300.exe Driver
2. V90wiz.ini File Contents

V90wiz.ini Driver File Contents (510_300.exe)

;;================= V90Wiz.INI ==== this file updated 09/02/98

;;This upgrades the modem to Rockwell release version 2.083

[General]
FileCnt=5
ValidatorCnt=6
PostFlashCmdCnt=5
QuickCheckMode=1
BackupDone=0
BackupFile=

[Options]
BlueScreen=1
OnePortOnly=0   ; faster testing if you set this to a modem port
ForceBackup=1    ;if 1, user can't get past the wizard page without backing up firmware

LogoBmp=OemLogo.bmp
OemAbout=For use with EigerCom 56K modems built with Rockwell chipsets.
OemAboutWebPage=World Wide Web Site: http://www.eigerlabs.com
OemAboutSupport=Tech Support Hotline: 1-510-739-2626
OemWarn=The following operation cannot be halted.\n\nAre you sure you want to continue?
ShowAndWait=1
TimedShow=0
ShowIfItu=0
ShowTrace=0
;ChkMdmRetries=2  ; If the PCMCIA modem has been powered-down, remove the ';' mark.

[Files]
;-----------------------------------------------------------------------
; filename, loadOrder, Flags, friendlyName[64], Description[256]
; Flags:  LOADER or UNLOADER or FIRMWARE
;  and:   TRANS or FINAL or BKUP (BKUP is added by program)
;
; be sure to set [General] FileCnt=
; leading spaces are stripped
;
File01=XmUL003.s37,  1, LOADER,         Firmware Loader,      FlashLoader -- loads via XModem
File02=XmDL003.s37,  1, UNLOADER,       Firmware Unloader,    Used to make Firmware backup via XModem
File03=5102012c.s37, 2, FIRMWARE TRANS, K56flex Firmware V2.012,  K56flex Driver for PCMCIA modems(supports AT-ITU?)
File04=5102083d.s37, 2, FIRMWARE FINAL, ITU V.90 Firmware V2.083, V.90 Driver for PCMCIA modems
File05=OrigBkup.S37,2,FIRMWARE BKUP,Failsafe Backup, Firmware V2.076-K56_DLL - Saved 05/19/98 10:25:22

[Validators]
;-----------------------------------------------------------------------
; ATI3,op,Ati3Text,ugCode,Maker,Model,Remark
; op can be:=(equals), * (contains), ! (notContains),  et.al.
; ugCode can be: UPDATABLE, TRANS, FINAL, or UNKNOWN
;
; leading spaces are stripped
; be sure to set [General] ValidatorCnt=
;
Validator01=ATI3, =, ATI3,           LOADFAULT, (Load Fault?), (Load Fault?), Maybe a modem in 'Load Fault' state
Validator02=ATI3, *, V1.000-K56_DLL, UPDATABLE, Eiger Labs Inc., EigerCom 56K Cellular Fax Modem, a modem I have
Validator03=ATI3, *, V1.120-K56_DLL, UPDATABLE, Eiger Labs Inc., EigerCom 56K Cellular Fax Modem, a modem I have
Validator04=ATI3, *, V1.200-K56_DLL, UPDATABLE, Eiger Labs Inc., EigerCom 56K Cellular Fax Modem, a modem I have
Validator05=ATI3, =, V2.012-K56_DLL, TRANS,     Eiger Labs Inc., EigerCom 56K Cellular Fax Modem, Been updated to Transitional
Validator06=ATI3, =, V2.083-K56_DLL, FINAL,     Eiger Labs Inc., EigerCom 56K Cellular Fax Modem, Been updated to ITU v.90



[PostFlashCmds]
;-----------------------------------------------------------------------
; Cmd##=type,AT_Cmd_Text
; ugCode can be: BKUP, TRANS, or FINAL
; Commands send after a flashload.  Usually start these with AT
; leading spaces are stripped, max len is 128 per command; max cmds: 10
; be sure to set [General] PostFlasCmdCnt=
;
Cmd01=BKUP,AT&F\V1&W
Cmd02=TRANS,AT&F\V1&W
Cmd03=TRANS,AT&Z1=17142218018
Cmd04=FINAL,AT&F\V1&W
Cmd05=FINAL,AT&Z2=17142600154

[Modem]
PortNum=2
RevId=V1.200-K56_DLL
Maker=Eiger Labs Inc.
Model=EigerCom 56K Cellular Fax Modem
IsUpdatable=1
IsK56flex=1
IsITU=0
IsTransitional=0
ItuStatus=2