1. 1800001g.exe Driver
2. README.TXT File Contents

README.TXT Driver File Contents (1800001g.exe)

RocketPort/RocketModem(R) Device Driver for Windows 2000(TM),
Windows XP(TM), and Windows 2003(TM) Operating Systems

---------------------------------
INSTALLING THE BOARD

For detailed installation instructions, see the Manual and
Reference Card that came with the RocketPort/RocketModem Board.
The Setup program that you install for the RocketPort/RocketModem
board has complete installation information.  To access this
information prior to installing the board, you can
Run>"HH ctmasetp.chm", or double click on the ctmasetp.chm file
from the Explorer.

---------------------------------------
RocketModemIII ONLY: FAX Class 1 & 1.0.

When using the Microsoft TAPI, there may be a long delay in 
responding to adaptive answer. You may receive the CONNECT message 
twice.

Some FAX applications including Microsoft FAX, may have problems 
operating in FAX class 1 & 1.0.  

For these reasons, Comtrol Technical Support recommends using FAX 
class 2.

---------------------------------
INSTALLING THE DEVICE DRIVER(PCI board)

Use the following procedure to install the device driver for
the first time with a RocketPort PCI board.

After the board is installed in the machine, when Windows 2000
powers up the Found New Hardware Wizard will see this new PCI
board as a PCI Simple Communications Controller.  Select
search for driver files and click next.  On the next sheet
select "Other Locations" to search for drivers.
You will then need to type in the path to the driver disk
or directory with the RocketPort drivers.

After the driver files are copied over, you can set the starting
com-port name by starting the Device Manager in the control panel,
select Multiport serial adapters and then
select the RocketPort card.  An options sheet is available
to adjust these options.

---------------------------------
INSTALLING THE DEVICE DRIVER(Pass 2 - RocketModem II PCI board)

If you are installing a RocketModem II PCI board for the first
time, the Found New Hardware wizard will start a second time 
after the driver for the RocketModem board has been installed.  
This second pass is necessary to locate and install the modems.

Initially, the wizard will see the (first) new PCI modem as a
Conexant Compatible External PnP Modem.  Select search for driver
 files and click next.  On the next sheet select "Other Locations" 
to search for drivers.  You will then need to type in the path to 
the driver disk or directory with the RocketModem drivers.

The remaining modems on the RocketModem II board will be installed
automatically once the installation for the first modem is done.

---------------------------------
INSTALLING THE DEVICE DRIVER(ISA board)

Use the following procedure to install the device driver for
the first time with a RocketPort ISA board.

After the board is installed in the machine, run the Add Hardware
Wizard from the Windows 2000 control panel.  Select Multiport serial
adapter to install.  Then select the <Have Disk> button.
You will need to type in the path to the driver disk or
directory with the RocketPort drivers.

The resources should be selected according to your switch
selection on the RocketPort board.  The RocketPort ISA board
switch setting default from the factory are 180H io-address.

After the driver is installed, you can set the starting
com-port name by starting the Device Manager in the control panel,
select Multiport serial adapters and then select the RocketPort card.
An options sheet should be available to adjust the options.

Reboot the machine after the installation.

---------------------------------
REGISTRY AND FILE DETAILS

You should not have to manually perform any registry of file
operations.  This information is included only for informational
purposes.

The following registry entries are made during the installation:

An entry for each board is made under the MultiPortSerial GUID:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Class\{50906CB8-...}

An entry for each port is made under the Ports GUID:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Class\{4D36E978-...}

Service entry is made as:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\RocketPort

The Enum branch is hidden from the user, a special tool(pnpreg /U)
has been known to un-hide it, generally speaking you should not need
to go into this registry area.
For PCI RocketPort boards, a node(PCI Vendor ID: 11FE) is made under:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Enum\Pci\xxxx

For ISA RocketPort boards, a node is made under:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Enum\Root\MultiportSerial\xxxx

For all ports, nodes are made under:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Enum\CtmPort\RkPort\

The rocket.sys file is copied to \WINNT\SYSTEM32\DRIVERS.
The ctmasetp.dll, ctmasetp.chm files are copied to \WINNT\SYSTEM32.
The netctmrk.inf, ctmaport.inf, mdmctm1.inf files are copied to \WINNT\INF,
  they may be renamed to oem#.inf.
The remaining files are copied to \WINNT\SYSTEM32\ROCKET.
---------------------------------
CONTACTING TECHNICAL SUPPORT


CORPORATE HEADQUARTERS:
  email:  support@comtrol.com
  web:    http://www.comtrol.com
  ftp:    ftp://ftp.comtrol.com
  fax:    (763) 494-4199
  phone:  (763) 494-4100

COMTROL EUROPE:
  email:  support@comtrol.co.uk
  web:    http://www.comtrol.co.uk
  fax:    +44 (0) 1 869-323-211
  phone:  +44 (0) 1 869-323-220


---------------------------------

Comtrol is a trademark of Comtrol Corporation.
RocketPort and RocketModem is a registered trademark of Comtrol Corporation.
Windows is a trademark of Microsoft Corporation.


DOCUMENT NUMBER: 8000165