LAN Server 2.0/3.0 Introduction: ------------- This document describes the procedure to install NDIS driver on DOS LAN Requester and OS/2 LAN server 2.0 (or 3.0) for Realtek RTL8139 Fast PCI ethernet adapter. Location of Driver: \NDIS\DOS\RTSND.DOS (for DOS LAN Requester) \NDIS\OS2\RTSND.OS2 (for OS/2 LAN Server) Installing driver procedure on DOS LAN Requester : -------------------------------------------------- 1. Insert the IBM LAN Support Program (LSP) Version 1.30 (or 1.31) Diskette into your floppy drive A: . 2. Type A:\dxmaid and press <Enter> . 3. The screen will display the IBM logo. Press <Enter> twice until the "Environment Information" appears on screen. 4. Responds to the screen prompts, specifying the following values for each field,use the <Space Bar> to toggle between choices: Configuration for this computer? Yes Use existing configuration information? Yes Do you have adapter option diskettes? Yes Are you configuring for two adapters? No Do you need 802.2 interface support? Yes Source for LSP A:\ Target for new configuration C:\LSP Make sure that the values given above are correct, then press <Enter> to store your choices. 5. Insert the Realtek RTL8139 driver diskette in floppy A,and specify your pathname A:\NDIS\DOS,then press ENTER. 6. Follow screen instructions to complete the process. Simply pressing <Enter> for each screen display will select the default options. Press <Enter> until you reach the display prompting you to insert the LSP diskette. 7. Insert the LSP diskette as prompted. Press <Enter> to acknowledge completion of the action. 8. A screen showing the current configuration detected will be displayed. It should show the Realtek RTL8139 adapter and the protocols already selected (i.e., "IBM IEEE 802.2" and "IBM OS/2 NETBIOS"). 9. Press <F4>. to save the new configuration. This completes the LSP installation. 10. Save the configuration and reboot your computer. 11. Insert the DOS LAN Requester Install Diskette 1 into your floppy drive. 12. Type A:\INSTALL <Enter> 13. The IBM logo will again appear on the screen. Press <Enter> to move on to the next screen. 14. Follow screen instructions, pressing <Enter> to move from screen-to-screen until you are prompted to indicate the pathname of the DOS LAN Requester directory (C:\DOSLAN ). 15. Specify the pathname (C:\DOSLAN is the default) for the DOS LAN Requester directory . Then press <Enter> to continue. 16. The program will ask you for the services that you require. 17. Highlight the appropriate option. Select either "Send messages" or "Send, View, Edit, and Log message" option. (Normally, second option "Send, View, Edit and Log message" is selected). 18. Specify the PC's ID and domain ID. 19. Follow screen prompts to complete the installation. Installing driver procedure on OS/2 LAN Server 2.0/3.0 : ------------------------------------------------------ Before you start with the installation process, make sure that OS/2 LAN Server is properly installed. Similarly, your adapter should also be properly installed in your server. 1. Copy RTSND.OS2 and RTL8139.NIF files from your Driver diskette (\NDIS\OS2) to C:\IBMCOM\MACS. 2. Click the OS/2 LAN Service icon. 3. Select "Installation and configuration". The IBM logo should appear onscreen. 4. Click <OK>. 5. Select <Advance> and press <Enter>. 6. Select "Install or Configuration this Workstation." 7. Select server type, adding a server or domain controller. The "install or remove" selections should appear. 8. Select "Configure a component." 10. Click the "Configure" button. 11. Select "Configure workstation." 12. Select "RTL8139 Fast ethernet adapter" when prompted to identify you Network Adapter. Then click the <Add> button. 13. Select IBM NETBIOS from the list and click the <Add> button. 14. Select <OK> to confirm all selections. 15. Follow screen instructions to complete the process, selecting <OK> to accept default selections. 16. Continue pressing <OK> until your screen prompts you to backup old CONFIG.SYS and AUTOEXEC.BAT and create a new CONFIG.SYS and AUTOEXEC.BAT. Also select <OK> to confirm this. 17. Installation is complete now. Reset your PC by turning it off and on. Note: ----- 1. The DOS version must be bellow DOS 5.0 when install DOS LAN requester into your system. 2.sample protocol.ini: [RTL8139] DriverName=RTSND$ EtherID=@52544C111111 ;This keyword is used to desinate a RTL8139 ;adapter by assigning it's ethernet ID ;when more than one adapters exist on one ; system. BusNo=@00 ;This keyword is used to desinate a RTL8139 ;adapter by assigning it's PCI bus number ;when more than one adapters exist on one ; system.(must be used with 'DeviceNo' keyword) DeviceNo=@0A ;This keyword is used to desinate a RTL8139 ;adapter by assigning it's PCI Device number ;when more than one adapters exist on one ; system.(must be used with 'BusNo' keyword) Speed= 100/10 ;This keyword is used to force RTL8139 adapter ;to speed 10M or 100M mode. If not present, ;the driver will auto-detect the speed.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.