1. expdrv.exe Driver
2. ANAEXPRE.INI File Contents

ANAEXPRE.INI Driver File Contents (expdrv.exe)

[version]
$Revision:   1.5  $
$Date:   17 Oct 1996 16:58:50  $

[setup]
plottername=Anagraph Express Plotters (HPGL)
page=1010100,13847,1000
*****PageX,PageY,Resolution
notes=When plotting for the first time after a plotter power down select one of the (initialize) tools in the Cut/Plot menu in order to initialze the plotter correctly. Otherwise, the plotter will not plot. 
cut=0,0,0,0,0,0,1,0,0,0,1,369,372,0,3,0,0,0,0,0,10,0,0
tile=0,0,0,0,0,0,0,0
move1=91,130,30,18,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
move2=91,130,30,18,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
move3=91,130,30,18,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
move4=91,130,30,18,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
moveLimit1=0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
moveLimit2=0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
MaxVector=1000000
generic=1
XYMoveAbs=1
ArcAbs=1
ArcSupport=0
SendInitBefore=1
setupplot=307,536

[MoveControl]
Variables=3
V1=Velocity,cm/s,0,91,VS%d
V2=Pressure,grams,50,400,TP%d
V3=Angle Offset,degrees,0,90,AO%d
V4=Tool Offset,units,0,500,TO%d

[Interrogation]
Factors=OF;,200,20,13,%ld,%ld
HardClip=OH;,500,30,13,%*ld,%*ld,%ld,%ld
Digitize=DP;
CurrentPos=OD;DC;,200,30,13,%ld,%ld,%*ld
;PlotterID=OI;,200,50,13,%Fs

[Generic]
AbsMove=PA
RelMove=PR
MoveUp=PU%.0lf,%.0lf
MoveDn=PD%.0lf,%.0lf
AbsArc=AA%.0lf,%.0lf,%.2lf
RelArc=AR%.0lf,%.0lf,%.2lf
Pause=NR
EndJob=
StartJob=RS39.37
;RS=Resolution 39.37, 100, 236.22, 393.7 (steps/mm) default=39.37
Term=;\r\n

[Tool1]
ToolInit=IN;SP0
ToolEnd=

[Tool2]
ToolInit=IN;SP1
ToolEnd=
Variables=2



[TOOLS]
Number Of Tools=2
Tool 1 Name=Knife
Tool 1 Type=1
Tool 2 Name=Pen
Tool 2 Type=0


[Resolution]
;Low=1
;Med=5
;High=25
;CutResBase=.0254
;ArcFitRes=.0254

[Port Setup]
commset=9600,n,8,1,p
;TXThreshold=10000
;TransmitBufSize=10000
;ReceiveBufSize=1024
;handshaking=0,0,0,0,0,0,0,1,1,17,19,100,900,0,0
;ReportError=0xFFFF
Port=1
Spool=0
Use DOS Device=0

[notes]
The plotter performs a service loop when an IN is received. This can be 
annoying and is not necessary between jobs, but only necessary after the 
plotter is first powered up.