ASOUND-LINK Version 2.02.12 - December 9, 1998
===================================================
Bug Fixes
----------
795 V.34 CRC problems while calling different providers
791 V.34 does not connect when low SNR
787 Dialing from HyperT with no phone line connected causes machine to hang
758 Livingston modem V90 connection fails (Pre Filter)
747 RTK:Win98 crashes or stops to respond during wake-up on ring
Improvements/Changes/Requirements
---------------------------------
784 USB: drivers kit update - preparing for distribution
800 Move INF parameters from external loading to internal settings
790 Several V.90 problems fix
772 Change of RRN set from V42 parameters
760 Add parameter for delay before resuming error-counting after RRN
ASOUND-LINK Version 2.02.05 - November 29, 1998
===================================================
Bug Fixes
----------
757 Connection to K56surfr modem fails
753 V.90 for USB, A-law RRN calibrations, and general V.90 update
752 Call progress should support filter: 296-504
749 USB: V8 problem with connection to USR
747 RTK: Win98 crashes or stops to respond during wake-up on ring from RealTek
745 Caller ID detection problem
744 Modem fails to connect to Cirrus modem (V8 bug)
739 USB: Sudden explosion of Error Energy in V.90
733 Sine wave transmission mode stopped working
728 Support dial tone threshold with PTT wizard
727 V.42 must not be negotiated when connected with Bell 103, v21 and V23 protocols
724 Incorrect transmission level in V.90 & K56 flex in phase 3
720 Singapore and China should be marked as A-law
716 Modifications for Livingstone modem
697 V.32 - better performance
695 Rate negotiation leads to disconnection
694 USB: V.90 connection problem vs. USR
Improvements/Changes/Requirements
---------------------------------
756 Add homologation parameter for blacklisting timeout
754 Add platform-dependent dynamically loaded data pump parameter for all platforms
751 New Sregs value for V42 RRN command
735 Support V90 mode in which v8bis will not be run in any case
731 Default Country Settings support by new SLCustom
726 Adjust default homologation settings for dial tone wait time
719 USB: Software ROHM (part 1) is added to USB project
714 New (approved) standard for BlackList
713 Implement range checking for the following homologation parameters: Dial Tone Wait Time (SReg 6), No Answer Timeout (SReg 7) and DTMF Dial Speed (SReg 11)Implement range checking
712 Implement datapumps' parameter loading from registry
706 DC removal needed
699 USB: Enable retrain due to ovf. & unf. - while in 'extended' data mode.
693 Show real echo canceler length with mtl_show or showDiag
691 USB: V90 must work with PTC gap of 4 from phase 3
682 Support for Power-Up Notification
565 L: Fax/Data Adaptive Answer (AT+FAE)
564 L: Distinctive Ring Support required
ASOUND-LINK Version 2.00.06 - October 8, 1998
=================================================
Bug Fixes
----------
618 lots of CRC error due to high rate in V.90
590 V.32 connects @ 14400 rather than 9600
582 When Dial string faulty, Modem to return ERROR immediately and NOT go off hook
503 V42 connection problems over V.32 when other modem is set to rate 9600
Improvements/Changes/Requirements
---------------------------------
605 New Modem's property page
603 AT#UD support in V.34
600 Power reduction support in V.90
587 Logging improvements (VxDMon)
583 56KFlex resides in separate VXD
577 Renaming: changing the hard-coded conventions (drivers & Registry entries)
563 Full Homologation and V.90 support
536 RTK: Rate Converter: Support 48 to 9.6 + MMX
499 at%t commands support
ASOUND-LINK Version 1.53.07 - August 18, 1998
================================================
Bug Fixes
----------
SCR #528 - Rtk: CRC Error Problems + Installation problems in OSR2
SCR #543 - Rtk: There is noise during start of modem session when 3D is active
SCR #529 - Rtk: Audio Echo problems with Phone Applications
SCR #538 - Rtk: Mouse stops to move after ALS300 modem installed
Improvements/Changes/Requirements
---------------------------------
SCR #542 - Ksn: Modem may continue carrier after closing com port
ASOUND-LINK Version 1.53.03 - August 5, 1998
================================================
Bug Fixes
----------
SCR #507 - Thc: Incorrect burning file
SCR #483 - AUTOMODE: Does not connect to a B103 caller
SCR #426 - L: V.34 lib incompatibility
SCr #520 - Rtk: Modem's activation changes audio volume
SCR #513 - RTK: Midi support
SCR #290 - Line disconnected immediately when Rx fax/voice/data call
Improvements/Changes/Requirements
---------------------------------
SCR #526 - Changes in mdm*.inf for the SLlite
SCR #513 - RTK: Midi support
SCR #500 - AD1821 : EEPROM support for AD1821 and AD1821A
SCR #498 - Enabled Speaker - Audio mixing during call progress
SCR #495 - Support required from callprog for continuous dtmf dialing when s11=0
ASOUND-LINK Modio Version 1.52 - JUNE 15, 1998
=============================================
Bug Fixes
----------
SCR #251 - Uninstall procedure doen't warn before uninstalling Modio
SCR #349 - Nested interrupts in 56k flex while surfing
SCR #365 - 1 Minute delay after recording from Modem or Handset channel in QuickLink
Message Center ver 3.0 appl
SCR #367 - Typo error in Control Panel->Multimedia->ADI Sound Controller Record (5
SCR #370 - GT: System crashes when running sysmon after establishing a data connect
SCR #377 - TC: Can not record a message and play it to local handset
SCR #378 - In Pulse dialing, 'W' and ',' are treated the same as '1'
SCR #381 - Video Input slider in win95 mixer is reversed
SCR #390 - Problem with Pulse Dialing in voice mode (on some boards)]
SCR #391 - CallProg should support gain corrections to low/high freqs. in DTMF dialing
SCR #393 - CallerID is not detected properly
SCR #396 - DTMF in dialing long press not handled properly
SCR #399 - Fix Korea PTT parameters
SCR #403 - Voice Playback problems when Modem and Handset are selected
SCR #407 - tx power modification when using ATA is required
SCR #409 - Korean PTT problem with S6 and S7 registers
SCR #413 - ATH1 command must not cause a signal to be sent to the line
SCR #414 - K56 is run instead of V8 leading to crash
SCR #427 - Video Input Device not supported when Modem is running
SCR #439 - 56K Flex A Law problem in singapore
SCR #443 - AD1821 does not restore last set value of Mic Mute on initialization
SCR #444 - 56K flex - 46K does not work with 6dB pads
SCR #446 - ThC: S45=11 to be set as default in INF file
Improvements/Changes/Requirements
--------------------------------
- SCR #392 - Voice rx and tx level to be controlled by register s72
- Single DMA used for MO
- SCR #451 - KS: Audio controls to be muted when volume is minimized
ASOUND-LINK Version 1.51 - MARCH 17, 1998
=============================================
Bug Fixes
----------
SCR #359 - System crash upon changing AD1821 MA resources
SCR #347 - Crash in Stream manager when using System Monitor
SCR #311 - Cannot connect to Compuserve's 800 number
SCR #302 - System hangs at start of media player after Modio has been open once
SCR #299 - Connection is always made in Max rate when using the command AT+MS
SCR #362 - Audio Volume changes when Modio connects/disconnects (on some boards)
SCR #341 - Cannot connect to Juno 800 number with specific setup
SCR #275 - Sharp high pitch noise during ath1 and raising VID or AUX slide bar
Improvements
------------
A significant performance improvement has been achieved, resulting
in a lower CPU loading.
Changes
-------
Korea country selection forces now A-Low for K56Flex
ASOUND-LINK Version 1.5 - MARCH 4, 1998
============================================
Changes/Bug Fixes
-----------------
SOME IMPROVEMENTS WERE MADE TO 56K PROTOCOL
ASOUND-LINK Version 1.25 - February 5, 1998
===============================================
Changes/Bug Fixes
-----------------
******** - THIS VERSION SUPPORTS 56K
******** - SOME IMPROVEMENTS WERE MADE TO THE FAX
SCR #300 - Country dependent S-Regs are overridden by ATZ or AT&F
SCR #266 - 1821 problem when full duplex works using DirectSound
SCR #274 - Tx a fax from Apache to Modio, fails during training
SCR #258 - Receiving a fax after answering in voice mode
SCR #57 - ATD command does not support @ , !
SCR #184 - Call Forwarding feature doesn't work in MSphone application
SCR #277 - Modem hangs up after 15 min due to a graphic card
SCR #331 - Shutdown Problem using S3 VIRGE and VREG card
SCR #326 - Answer Tone (2100 ) Level too high
SCR #313 - Flash feature isn't working on some designs
ASOUND-LINK Version 1.24 - November 30, 1997
=================================================
Changes/Bug Fixes
-----------------
- SCR #203 - When dialing from Phone Dialer, sometimes the other side can't hear you
- SCR #278 - Adjust default values for S6,S7 for Korean PTT, HS Record level for Canadian PTT
- SCR #265 - When calling Modio using Connectix VP appl, ring isn't detected by appl.
- - Low rate connections problem - improved decision for 24000/26400 & 26400/28000
ASOUND-LINK Version 1.23 - October 22, 1997
=================================================
Changes/Bug Fixes
-----------------
- SCR #243 - Microphone is muted when switching from handset to speakerphone
- SCR #256 - Sometimes voice modem can't accept calls
- SCR #266 - Problem when using DirectSound in full duplex mode
The new Key:
HandsetRecordingGain [128]
CallProgWaitForDialTone [2] /// Sec (sreg 6)
CallProgWaitForCarrier [60] /// Sec (sreg 7)
ASOUND-LINK Version 1.22 - September 30, 1997
=================================================
Changes/Bug Fixes
-----------------
- SCR #186 - Monitor Incoming call in Bitware
- SCR #189 - Connectix Videophone recognizes Modio
- SCR #193 - Support partial Dialing (;)
- SCR #207 - Quicklink Message Center recognizes Modio
- SCR #218 - Dialtone isn't detected when Modio dial out to TNC Mertz modem using HyperTerm
- SCR #221 - Fax Tx problem with TNC Mertz using RingCentral appl.
- SCR #230 - Fax Connects in 2400 bps
- SCR #231,#232, #235, #236 - Fax Sending problems with Murrata/Panafax
- SCR #233, #234 - Fax Tx/Rx problems with PCTEL 288 fax/modem card using BitWare appl
- SCR #237 - Ring is not detected after playing back a message through the handset
- SCR #239 - Connection fails when trying to connect with no automode
- SCR #240 - ATW does not work properly
- SCR #241 - V34 33.600 connection problems with ZoomK56
- SLLights Modio monitor was added
- Cyrix M1,M2 processors supported
- Joystick problems in DOS Box games
ADI Singapore bug list:
- (30) - V.22 problems with USR
- (53) - hyperterminal window defocused
- (35,44-49) - Fax problems
- (33) - Dialtone isn't detected when Modio dial out to TNC Mertz modem using HyperTerm
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.