****************************************************************************
Solaris8.txt
*****************************************************************************
Installation Guide for the LSI Logic SDMS Solaris Driver, Version 4.07.00
This file describes the features and use of the LSI Logic SDMS Device Driver for
the Solaris 8 Operating system. It is divided into the following sections:
Introduction
Features
LSI Logic Devices Supported
Description
Creating the SYMHISL Driver Update Diskette
How to Install Your SDMS Solaris Driver
Installing the Driver During Solaris Installation
Updating Solaris with the driver
Troubleshooting
******************************* Introduction ********************************
Solaris 8 for x86 is an operating system designed to run on single or multiple
processors. It provides a command line interface environment and a graphical
environment that incorporates many high level features. Refer to the Sun
Microsystems Web site, www.sun.com/docs for Solaris 8 X86 documentation for
further details.
The SDMS driver, symhisl, allows the Solaris operating system to interface with
SCSI devices connected to these LSI Logic SCSI controller chips: LSI53C895A,
LSI53C896, LSI53C1010 and LSI53C1000. A list of features associated with this
driver along with its description is described below. The procedures to install
the symhisl driver during a new installation of Solaris 8 or to update the
driver with an existing installation of Solaris 8 are also included.
Note: Current Solaris 8 drivers can be downloaded from the LSI Logic web
site at http://www.lsilogic.com. After you are connected to this
web site, place your cursor on the Get Drivers option in the menu
bar. Click on the Drivers selection. Choose the Solaris operating
system for SCSI and click on the Go button. Follow the instructions
on subsequent screens to download the driver.
*******************************************************************************
IMPORTANT: This software has been tested on Solaris 8 FCS. This software will not
run on Solaris 7. LSI Logic assumes no responsibility or liability when a user
attempts to use this software with older versions of Solaris that LSI Logic has
not tested.
*******************************************************************************
* * * * * * * * * * * * * Features * * * * * * * * * * *
The symhisl driver supports these features:
o Synchronous negotiation (including Fast SCSI/Ultra SCSI/Ultra2 SCSI)
o Ultra160 Data Transfers (for LSI53C1010 and LSI53C1000)
o Ultra160 Domain Validation
o Ultra160 Double Transition (DT) data transmissions
o Multiple host adapters
o Disconnect/Reselect
o Multiple and non-contiguous Logical Unit Number (LUN) support
o Scatter/Gather
o Wide devices
o Tagged command queuing
o Multiprocessors
o Hot swapping of SCSI devices
* * * * * * * * LSI Logic Devices Supported * * * * * * * * *
All LSI Logic devices and host adapters have undergone a name change. They
have transitioned from a SYM prefix to an LSI prefix. No name changes have
occurred for the SDMS Solaris driver.
The symhisl driver is a Solaris 8 32-bit driver and supports these LSI Logic
devices and their associated host adapters:
o LSI53C895A (LSI8953U)
o LSI53C896 (LSI22910, LSI21002, LSI22902)
o LSI53C1000 (LSI8955U*)
o LSI53C1010 (LSI22915, LSI22903, LSI21040, LSI8955U**)
* 66 MHz
**33 MHz
* * * * * * * * * * * * * Description * * * * * * * * * *
The SDMS symhisl driver is designed to Sun Microsystems SCSA specifications
for device drivers. This driver allows connection of SCSI devices including
disk drives, CD-ROMS, and tape drives for PCI-based machines. To support a new
SCSI device, the Solaris 8 x86 architecture requires that the device complies
to the SCSI standard.
************************Installing the SDMS Solaris 8 Driver*********************
This section provides installation instructions for new and existing systems.
The SYMHISL Driver Update diskette can be used in one of two ways:
1. To use new drivers to install or upgrade the Solaris 8 operating environment
on a machine with new hardware.
-OR-
2. To add new drivers to support new hardware on an already installed and
booted system.
* * * * * * * New System Installation for Solaris * * * * * * *
You have the option of installing from a bootable Solaris 8 CD-ROM labelled
Software 1 of 2 or a Solaris 8 Diskette. These installation steps refer to the
Solaris Device Configuration Assistant Diskette as the boot diskette. If
installing from the Solaris 8 bootable CD-ROM, ignore the information about
reinserting and/or removing the Solaris Device Configuration Assistant Diskette.
The new system installation instructions follow:
To use the driver on the SYMHISL Driver Update diskette to install Solaris 8
(Intel Platform Edition) on a machine, follow the steps below. Use the
appropriate Solaris Device Configuration Assistant Diskette appropriate for
your release of Solaris 8 as the boot diskette.
1. Insert the Solaris Device Configuration Assistant Diskette into your
machine's diskette drive. Also insert the Solaris Installation CD-ROM;
or for network installation, verify with your system administrator that
the Solaris Network Installation image is available on your network.
2. Turn on your machine.
3. When the Solaris Device Configuration Assistant screen appears, choose
F4_Add Driver. The Bus Enumeration screen appears.
Then, the Install Supplemental Drivers screen appears.
4. Remove the Solaris Device Configuration Assistant Diskette from the
diskette drive and insert the first Solaris Driver ITU diskette you want.
5. Press F2_Continue.
6. The Loading Supplemental Driver Software screen appears, along with a
progress bar that shows the percentage of drivers that have been extracted
from the diskette. Drivers are read into memory and survive long enough
for the system to successfully boot to its installation program. When all
the new drivers on the diskette have been processed, the Continue
Supplemental Driver Installation screen appears.
7. Remove the Solaris Driver ITU diskette from the diskette drive and insert
the next Solaris Driver ITU diskette you want, if any for other devices.
If so, continue with Step 8; otherwise, proceed to step 10.
8. Press F2_Continue.
The Loading Driver Update Software screen appears, along with a progress
bar that shows the percentage of drivers that have been extracted from the
diskette. Drivers are read into memory and survive long enough for the
system to successfully boot to its installation program. When all the new
drivers on the diskette have been processed, the Continue Supplemental
Driver Installation screen appears.
9. Repeat Step 4 through Step 8 until all the Solaris Driver ITU
diskettes you want are installed.
10. When all the drivers are processed, remove the Solaris Driver ITU diskette
from the diskette drive and reinsert the Solaris Device Configuration
Assistant Diskette. Press F4 when done adding supplemental drivers.
After pressing F4, the Identified Device Drivers screen appears with a list
of all device drivers. For example, you would see at least symhisl-Device
Driver.
IMPORTANT: Do not remove the Solaris Device Configuration Assistant
Diskette from the diskette drive until you see the following
message displayed in a dialog box:
"If you want to bypass the device configuration and
boot screens when the system reboots, eject the
Device Configuration Assistant/Boot diskette now."
This message actually appears during Step 16.
11. Press F2_Continue.
The Solaris Device Configuration Assistant screen appears.
12. Press F2_Continue.
The Bus Enumeration screen appears.
The Scanning Devices screen appears. System devices are scanned. When
scanning is complete, the Identified Devices screen appears.
13. Press F2_Continue.
The message "Loading driver ..." appears followed by messages about the
drivers that are required to boot your system. After a few seconds, the
Boot Solaris screen appears.
14. At the Boot Solaris screen, select the device controller attached to the
device that contains your install medium.
15. Press F2_Continue.
Drivers for the device controller that you selected are displayed. Your
system boots to run the install program. The install program starts and
your machine begins booting the complete Solaris operating environment.
16. Proceed to configure your system when prompted to do so. After configuring
your system, click on the Begin Installation button.
The message indicated above appears now:
"If you want to bypass the device configuration and
boot screens when the system reboots, eject the
Device Configuration Assistant/Boot diskette now."
17. Remove the Solaris Device Configuration Assistant Diskette.
Some time later, the following messages appear and prompt you to
insert each of the Solaris Driver ITU diskette(s) required to
install into your machine:
Installing unbundled device driver support
Extracting driver list from tree..
<ITU diskette name> driver-name...
Please insert the Driver Update diskette labeled <ITU diskette name>
Press <ENTER> when ready.
18. Reinsert the SYMHISL Driver ITU diskette that you inserted earlier into the
diskette drive.
19. Press Enter.
Packages and/or patches that contain the new drivers are installed from
the diskette onto your machine. Messages about each installation appear
accordingly.
When the prompt asking:
Do you want to create a new instance of this package [y, n, ?, q]
Type y for YES and press Enter.
20. Remove the Driver ITU diskette from the diskette drive if drivers on other
Solaris Driver ITU diskettes are required. The system will prompt you with
this message:
"If you have additional Update diskettes to install (such as video), please
insert diskette now."
"Additional Update Diskettes?"
21. Type y for Yess if applicable.
Repeat this process until all drivers you need are installed.
When you type n for No and press Enter, this message appears:
"Installation of <SYMhisl.2> was successful."
The system automatically reboots your machine.
When the Solaris operating environment is finished booting and running, the
new devices whose drivers that you installed are available for use. To verify
the version number for the Solaris 8 symhisl driver, type at the prompt:
# modinfo | grep sym
The system will display the version number.
* * * * * * Existing System Installation for Solaris * * * * * * *
Before adding new or updated drivers, the newly supported hardware devices
should be installed and configured according to the instructions in the
corresponding Device Reference Page, if any. See the Device Reference Manual
for Solaris (Intel Platform Edition).
When the Solaris Intel Platform Edition software is already installed, the
simplest way to add new or updated drivers is to install the Driver ITU
diskettes as patches on your system. For more information about managing
diskettes and drives, see the System Administration Guide.
To add new or updated drivers, follow these steps:
1. Go to the root directory.
2. To see if the Volume Management software is running on the machine that
you are updating, type at the command prompt:
ps -ef | grep vold
3. To temporarily stop Volume Management if it is running, type this command
at the system prompt:
# /etc/init.d/volmgt stop
4. Insert the Solaris Driver ITU diskette into the diskette drive.
5. Mount the Solaris Driver ITU diskette at the /mnt mount point:
# mount -F pcfs /dev/diskette /mnt
Note: You must mount the Solaris Driver ITU diskette at this point
in the file structure to update your system successfully.
6. Execute the install script on the diskette:
# /mnt/DU/sol_28/i86pc/Tools/install.sh -i
The install.sh script searches for all new or updated drivers on the
diskette. When a new or updated driver is found, this prompt appears:
Unconditionally installing ITUs <ITU driver names>
(Some messages appear stating that your installing).
Then, the message prompts:
"Do you want to create a new instance of this package [y, n, ?, q]"
7. Type n for no.
Then, the message prompts:
"Do you want to overwrite this installed instance [y, n, ?, q]"
8. Type y for yes to overwrite the old driver.
9. When the installation has completed, and the install.sh script exits,
unmount the diskette by typing at the command prompt:
# cd /
# umount /mnt
10. Remove the Solaris Driver ITU diskette from the diskette drive.
11. Reboot your machine by typing at the command prompt:
# touch /reconfigure
# reboot
12. If you have not already done so, turn off your system, add the new
hardware, and turn on your system again.
13. At the << Current Boot Parameters >> prompt, type:
b -r
to force reconfiguration of the machine.
When the Solaris 8 operating environment is finished booting and running, the
new devices whose drivers that you installed are available for use. To verify
the version number of the Solaris 8 symhisl driver, type at the prompt:
# modinfo | grep sym
The system will display the version number.
***********************************Troubleshooting*****************************
Some informational or potential error messages may be preceded by a warning
message and displayed by the operating system. In the listed message
descriptions, the SYMHISL<n> signifies that <n> can be replaced by a number
assigned to it by the operating system. That value helps to identify the
SCSI bus that is reporting the error. <s> and <x> are placeholders for strings
and numbers that the system will display.
SYMHISL<n>: This hardware not supported by this driver
SYMHISL has been told to control a LSI53C895A, LSI53C896, LSI53C1010 or
LSI53C1000 controller, which is made by a manufacturer other than
LSI Logic. This adapter requires a special driver provided by that
manufacturer. Please contact the manufacturer for assistance.
SYMHISL<n>: Failed to map device registers
SYMHISL was unable to access the hardware registers necessary for
operation. The operating system did not properly configure the PCI
device.
SYMHISL<n>: NVS error, failed to restore value of 'reg' property
SYMHISL was able to access the resources needed to determine NVS
configuration but was not able to return the system to its prior state.
Further configuration errors may occur.
SYMHISL<n>: NVS error, failed to map system memory
NVS data can't be used
SYMHISL<n>: NVS error, failed to update 'reg' property
NVS data can't be used
SYMHISL<n>: NVS error, failed to allocate memory
NVS data can't be used
SYMHISL<n>: NVS error, unable to find 'reg' property
NVS data can't be used
For each of the above errors, SYMHISL was not able to access NVS
configuration data to see if it exists. On some systems, this will not
be a problem. On other systems, however, NVS data contains the
configuration information for this adapter and SYMHISL is not able to
use that configuration. This may cause the user to manually configure
the driver using the symhisl.conf configuration file. Please refer to the
man page driver.conf(4), which is the standard reference on how to edit
the symhisl.conf file. The instructions for editing symhisl.conf can also
be found in the path /kernel/drv/symhisl.conf.
SYMHISL<n>: Hardware not properly enabled by system, cmd=xxxxh
The system has not properly enabled the configuration resources that
SYMHISL needs in order to use this hardware. The cmd=xxxxh value needs to
be reported to technical support.
SYMHISL<n>: Unsupported 64-bit register address
Please load 64-bit version of kernel and driver
This version of the SYMHISL driver does not support physical addresses
using 64-bit values. Contact LSI Logic Technical Support at 719-533-7230
to determine if a new driver is available to support 64-bit version.
SYMHISL<n>: The host adapter id in the .conf file is being ignored
because the SCSI BIOS Configuration Utility will override it.
The symhisl.conf file has a line (scsi-initiator-id=x) which is used to
change the host adapter SCSI ID. That line is being ignored because the
SCSI BIOS Configuration Utility has set the SCSI ID. Please use the SCSI
BIOS Configuration Utility to change the SCSI ID.
SYMHISL<n>: Ignored invalid scsi-initiator-id value = <x>
The symhisl.conf file has an invalid scsi-initiator-id value as displayed
in the error message. The allowable values are in the range 0..15.
SYMHISL<n>: <s> property value is too large
Using maximum value of <x>
A property value in the symhisl.conf value is greater than the maximum
allowed value. The driver will use the value <x> instead.
SYMHISL<n>: <s> property value is too small
Using default value of <x>
A property value in the symhisl.conf value is less than the minimum
allowed value. The driver will use the value <x> instead.
SYMHISL<n>: Could not allocate memory to read configuration data
The driver was unable to allocate memory required to process the
configuration data. This means that the configuration was not properly
determined. To fix this you may need to manually configure the driver
using the symhisl.conf file.
SYMHISL<n>: Failure reading NVM configuration data
The driver was unable to read the configuration data supplied by the SCSI
BIOS Configuration Utility. This means that the configuration was not
properly determined. To fix this you may need to manually configure the
driver using the symhisl.conf file.
SYMHISL<n>: Failure reading NVM manufacturing data
The driver was unable to read the configuration data supplied by the
manufacturer. This means that the adapter configuration may be incorrect
and unknown errors may occur. Please contact your manufacturer for a
replacement adapter.
SYMHISL<n>: The boot ROM configuration utility has SCAM enabled
but this driver is not capable of SCAM. Please disable SCAM
in the boot ROM.
Some older versions of the SDMS Boot ROM are capable of using the SCAM
protocol to assign SCSI IDs. The SYMHISL driver is not capable of using
SCAM. In order to properly configure your system, please disable SCAM
using the SCSI BIOS Configuration Utility.
SYMHISL<n>: Configuration data is corrupt and will be ignored
The configuration data provided by the SCSI BIOS Configuration Utility
has been determined to be corrupted. Run the SCSI BIOS Configuration
Utility to correct this error.
SYMHISL<n>: Unknown synchronous value in NVM data = <x>
The SYMHISL driver needs to be updated to understand this new synchronous
configuration data value. Until the driver is updated, synchronous mode
will be disabled.
SYMHISL<n>: Unknown width value in NVM data = <x>
The SYMHISL driver needs to be updated to understand this new wide
configuration data value. Until the driver is updated, wide mode will
be disabled.
SYMHISL<n>: Unable to make reset notification callbacks
The SYMHISL was unable to notify the target device driver of a SCSI bus
reset. The target driver may start to malfunction because of this.
SYMHISL<n>: Disabling queue tags for target ID <x>
The SYMHISL driver has determined that the specified target is no longer
responding to queue tagged I/O in a proper manner and has disabled queue
tags for that device. This usually means that the specified device does
not support queue tags. To disable this message, disable queue tags for
the given device using the SCSI BIOS Configuration Utility.
SYMHISL<n>: Device (ID=<x>, LUN=<x>) not supported
A Solaris target driver attempted to initialize a device whose SCSI target
ID was out of the support range or whose LUN was not zero. This warning is
most likely triggered by illegal entries in the target driver's conf file.
SYMHISL<n>: ddi_dma_sync() failed for data buffer
Data corruption may occur
SYMHISL<n>: ddi_dma_sync() failed for I/O data at <xxxxxxxx>
Data corruption may occur
SYMHISL<n>: ddi_dma_sync() failed for Adapter data
Data corruption may occur
A call to the operating system's ddi_sync_dma function failed. As a
result, the system data caches may not be properly synchronized with
system main memory. This may result in data corruption or failure of
the symhisl driver to function properly.
SYMHISL<n>: ddi_dma_numwin() failed
SYMHISL<n>: ddi_dma_getwin() failed
SYMHISL<n>: ddi_dma_alloc_handle: <xx>h unknown/impossible
SYMHISL<n>: ddi_dma_buf_bind_handle: DDI_DMA_INUSE impossible
SYMHISL<n>: ddi_dma_buf_bind_handle: <xx>h unknown/impossible
SYMHISL<n>: ddi_dma_unbind_handle: failed
The operating system failed to respond to the named routine in a known
manner. This is a fatal error that is not recoverable. Please report this
error to LSI Logic Technical Support by calling 719-533-7230.
SYMHISL<n>: Device in a slave-only slot and is unusable
SYMHISL<n>: Hi-level interrupts not supported.
The adapter is in a slot that cannot be used with this driver. Please
try moving the adapter to a different PCI slot.
SYMHISL<n>: Failed to attach. This adapter will not be installed.
Because of the previous error, this adapter could not be "attached" to the
I/O subsystem and will not be accessible. See the previous error message
and solve that problem.
SYMHISL<n>: Failed to allocate memory
The SYMHISL driver was unable to allocate the memory needed during
initialization. You may have run out of available memory.
SYMHISL<n>: Unbind failed!
The driver had a problem when attempting to unload itself.
This is a fatal error.
SYMHISL<n>: Unable to obtain soft state structure
The SYMHISL driver was unable to initialize a required data structure and
therefore did not load. Please call technical support at 719-533-7230.
SYMHISL<n>: Failed to attach interrupt handler
The SYMHISL driver was unable to initialize the interrupt handler as
required. Please call technical support at 719-533-7230.
SYMHISL<n>: The adapter is malfunctioning
SYMHISL<n>: The adapter is either malfunctioning, of an unknown type,
or a revision that is not supported
The driver is not able to communicate with the hardware. You may need to
update your driver or your hardware.
SYMHISL<n>: Failed to create DMI minor node
The SYMHISL driver was unable to create a device node for the driver's
DMI interface. If you are not using the DMI then you may safely ignore
this message.
SYMHISL<n>: Could not attach to the SCSI subsystem
The SYMHISL driver was unable to communicate with the Solaris 8 SCSA
subsystem. You may need to update your driver.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.