<?XML Version="1.0"> <nidocument> <nicomment> SM2044/SMX2044 Series DMM error codes </nicomment> <nierror code="0"> SMX2044: no error </nierror> <nierror code="-1"> SMX2044: Error: cannot find valid calibration file </nierror> <nierror code="-2"> SMX2044: Error: DMM number invalid (not configured) </nierror> <nierror code="-3"> SMX2044: Warning: DMM overrange error </nierror> <nierror code="-4"> SMX2044: Error: DMM error occurred during operation </nierror> <nierror code="-5"> SMX2044: Warning: Invalid rate value used </nierror> <nierror code="-6"> SMX2044: Warning: Invalid function value used </nierror> <nierror code="-7"> SMX2044: Error: Cannot find valid configuration file </nierror> <nierror code="-8"> SMX2044: Error: Card ID in error, could be H/W fault </nierror> <nierror code="-9"> SMX2044: Warning: Invalid range value used </nierror> <nierror code="-10"> SMX2044: Error: Dmm not initialized </nierror> <nierror code="-11"> SMX2044: Error: DMM not responding </nierror> <nierror code="-12"> SMX2044: Warning: DMM counter out of range </nierror> <nierror code="-13"> SMX2044: Warning: Trigger buffer count error </nierror> <nierror code="-14"> SMX2044: Error: Trigger disarm error </nierror> <nierror code="-15"> SMX2044: Error: DMM Not found on PCI bus </nierror> <nierror code="-16"> SMX2044: Error: Cannot find valid calibration record </nierror> <nierror code="-17"> SMX2044: Warning: Dmm already initialized: in use </nierror> <nierror code="-18"> SMX2044: Error: Fail H/W init </nierror> <nierror code="-19"> SMX2044: Warning: Can't change rate in Cap mode. </nierror> <nierror code="-20"> SMX2044: Error: can't open dmm.cfg file </nierror> <nierror code="-21"> SMX2044: Error: can't access H/W, wrong address of fail </nierror> <nierror code="-22"> SMX2044: Error: can't find calibration record for DMM </nierror> <nierror code="-23"> SMX2044: Warning: Illegal function selection </nierror> <nierror code="-24"> SMX2044: Error: Not defined </nierror> <nierror code="-25"> SMX2044: Warning: Wrong rate parameter, see rate definition </nierror> <nierror code="-26"> SMX2044: Error: Can't read ID from DMM </nierror> <nierror code="-27"> SMX2044: Error: Trigger circuit error </nierror> <nierror code="-28"> SMX2044: Warning: wrong value in the number of samples </nierror> <nierror code="-29"> SMX2044: Warning: wrong parameter value </nierror> <nierror code="-30"> SMX2044: Error: Communication error with DMM uP </nierror> <nierror code="-31"> SMX2044: Warning: Function can not be selected, or not available </nierror> <nierror code="-32"> SMX2044: Error: Cal record error </nierror> <nierror code="-33"> SMX2044: Error: A process timed out </nierror> <nierror code="-34"> SMX2044: Error: Guard crossing is broken </nierror> <nierror code="-35"> SMX2044: Error: Microcontroller communication error </nierror> <nierror code="-36"> SMX2044: Error: Communication overrun </nierror> <nierror code="-37"> SMX2044: Error: Communication frame </nierror> <nierror code="-38"> SMX2044: Error: Communication receive FIFO </nierror> <nierror code="-39"> SMX2044: Error: Communication parity error </nierror> <nierror code="-40"> SMX2044: Warning: Overrange reading </nierror> <nierror code="-41"> SMX2044: Warning: Underrange reading </nierror> <nierror code="-42"> SMX2044: Error: Type missmatch between Cal file and H/W </nierror> <nierror code="-43"> SMX2044: Error: Serial number missmatch between Cal file and H/W </nierror> <nierror code="-44"> SMX2044: Warning: Controller version does not suppor this function </nierror> <nierror code="-45"> SMX2044: Warning: DMM Requires calibration by (more than just self cal) </nierror> <nierror code="-46"> SMX2044: Error: Can't open PCI device. Already open ? </nierror> <nierror code="-47"> SMX2044: Warning: Temperature too low </nierror> <nierror code="-48"> SMX2044: Warning: Temperature too high </nierror> <nierror code="-49"> SMX2044: Warning: Wrong TC type </nierror> <nierror code="-50"> SMX2044: Error: Card does not have all PCI items. </nierror> </nidocument>Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.