===========================================================
SiS PCI Giga Ethernet Adapter Diagnostic Program v2.23
===========================================================
This Diagnostic program contains the following functions:
1. Adapter Information
2. Diagnostic Tests
(1). Adapter Information
1.1 Display Adapter Information, including
Chip ID 0190 (or 0191)
Node ID 00 XX XX XX XX XX
Bus Mode PCI 32-bit
Media type 100 Full Duplex
I/O Base Address e000
Interrupt Number 000b
PHY Address X
MII ID XXXX XXXX
Msater Bus Enable
1.2 Set Media Type -- User can select one of the following
media type here. Once the media type is selected, the
latter Diagnostic Tests will be run with this media type.
Diag will auto detect the link speed and duplex mode
when "Auto Config" is selected.
Note that the operating speed of 1000Mbps cannot be forced.
The link with 1000Mbps only created with auto-detected,
when the link partners both have 1000Mbps capability.
Auto Config
10 Mbps Half
10 Mbps Full
100 Mbps Half
100 Mbps Full
(2). Diagnostic Tests
Basic Tests : Include following 3 basic tests.
PCI registers I/O test
MAC registers I/O test
MII registers I/O test
Controller Loopbacks : Test MAC internal loopback mode.
External Loopback : Type "Diag19x /e", then the item of external loopback will show up
Send Magic Packet : Specify Destination Address and Send a
magic packet to wake-up other PC.
Send Wake-up Frame : Specify wake-up frame to wake-up other
PC.
Set Wake-up Event : Set wake-up event to SIS LAN adapter.
(Note) After you Set wake-up event, you can turn off the power
by press power button. Then wait for wake-up event.
2 Station Test : To run this test, you need two station, Sender and
Reponder, connected with an ethernet cable.
Sender : Send packet and wait for response
Responder: Listen packet from sender and send response to sender
=========================
Steps To test wake-on LAN
=========================
0. Enable the PM Wake Up Events "MACPME" in the "Power Management Setup" of BIOS option.
1. Test Wake-up frame
PC1 that will be waked up PC2 that will wake up PC1
(This M/B should support
Ring-in or Wake-on-LAN)
----------------------------- --------------------------
a. Select "Set wake-up Event" a. Wait until PC1 is ready
b. Set wake-up Frame and b. Send wake-up frame
byte mask
c. Power off
d. Wait for PC2 to wake me
up
2. Test Magic Packet
PC1 that will be waked up PC2 that will wake up PC1
----------------------------- -------------------------
a. Select "Set wake-up Event" a. Wait until PC1 is ready
b. Set Magic Packet b. Send Magic Packet
c. Power off (Destination Address
d. Wait for PC2 to wake me must be PC1 MAC addr)
up
3. Test Link Change
PC1 that will be waked up
-----------------------------
a. Select "Set Wake-Up Event"
b. Select "Link Change"
d. Power off
e. change the condition of network-connection.
(Link on / Link off)
=========================
How to Set wake-up Frame
=========================
SiS190/SiS191 supports 8 wake-up frames.
Each Wake-up frame is up to 128 bytes.
Frame 1: 00XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
BitMask: 1XXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Fill frame with any pattern you want.
Each '1' in Byte mask means byte you want to match.
Ex.
Frame X: 00E00600902212345678XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
BitMask: 0000001111XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
This means you want to match byte 6 to 9 -- 12 34 56 78
Any received packet that matches byte 6 to 9 will be a wake-up
frame.
Note: If you don't select media type ,
the default media type is "Auto Config".
Then all "Diagnostic Tests" will run with "Auto Config".
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.