; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; File: SIRDASMC.INF ; ; Based on IRDASMC.INF. ; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; "SMC IrCC - Fast Infrared Port, SP1" (Special version 1) ; ; This INF is identical as IRDASMC.INF except that this will install ; "RxForceDrq" string value to the registry ; that is required for SiS and VIA chipsets. ; The device description name in the device manager has "SP1" in it. ; ; "RxForceDrq" is implemented in v.5.1.3600.2 or later, but not in ; v.5.2.3630.0. ; ; In the future, IrCC bundled with SiS and VIA chipsets should have ; SMCF020 PnP ID in BIOS rather than SMCF010 so that INF can figure ; out what to install. For now, this special version of INF ; file treats both SMCF010 and SMCF020 as the same device that ; is bundled with SiS or VIA chipsets. ; ; 6/5/02, 5/30/02, 5/15/02, 5/3/02 (yo) ; 4/30/02 (yo) ; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; File: IRDASMC.INF ; ; INF to install SmcIrda.Sys NDIS 5.0 Miniport for SMC IrCC ; on Windows 2000 and Windows XP ; ; Copyright 1997 - 2002 Standard Microsystems Corp. ; (nw) ; ; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; [version] CatalogFile=irdasmc.cat ;LayoutFile=layout.inf ; should only use this if installing as part of OS signature="$Windows NT$" Class = Infrared ClassGUID = {6bdd1fc5-810f-11d0-BEC7-08002BE2092F} provider=%strSMC% DriverVer=05/15/2002, 5.1.3600.2 [DestinationDirs] DefaultDestDir=12 ; %windir%\system32\drivers SysCopyFiles=12 [Manufacturer] %strSMC%=SMC_IRCC [ControlFlags] ExcludeFromSelect=*SMCF010 ExcludeFromSelect=*SMCF020 [SMC_IRCC] %*SMCF010.DeviceDesc%=*SMCF010.ndi, *SMCF010 %*SMCF020.DeviceDesc%=*SMCF020.ndi, *SMCF020 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; SMCF010, SMCF020 Block ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; If this INF file is used for IrCC with Intel Chipset, ; then *SMCF020.ndi.reg must be deleted from *SMCF010.ndi section. [*SMCF010.ndi] DelReg=SMC_DelReg AddReg=*SMCF010.ndi.reg,*SMCF010.ndi.param,*SMCF020.ndi.reg BusType=14 ; ISAPNP Bus Characteristics = 0x84 ; NCF_PHYSICAL, NCF_HAS_UI CopyFiles=SysCopyFiles DriverVer=05/15/2002, 5.1.3600.2 [*SMCF020.ndi] DelReg=SMC_DelReg AddReg=*SMCF010.ndi.reg,*SMCF010.ndi.param,*SMCF020.ndi.reg BusType=14 ; ISAPNP Bus Characteristics = 0x84 ; NCF_PHYSICAL, NCF_HAS_UI CopyFiles=SysCopyFiles DriverVer=05/15/2002, 5.1.3600.2 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Add Registry Section for Install ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [*SMCF010.ndi.reg] HKR,Ndi,Service,0,"SMCIRDA" HKR,Ndi\Interfaces,DefUpper,0,"ndisirda" HKR,Ndi\Interfaces,UpperRange,0,"ndisirda" HKR,Ndi\Interfaces,DefLower,0,"nolower" HKR,Ndi\Interfaces,LowerRange,0,"nolower" HKR,Ndi,BoardType,0,"3" HKR,Ndi,RequiredAll,0,"MS_IrDA" ; ; This is the text that shows in the display area at the bottom ; of the Network dialog when this Adapter is selected in the ; scrolling window above. ; HKR,Ndi,HelpText,,%strSmcIrdaHelp% [SMC_DelReg] HKR,,EnumPropPages32 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Special section for SMCF020 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [*SMCF020.ndi.reg] ; ; SiS & VIA DMAC Options ; ; RxForceDrq: Any TRUE value enables Force Drq when RX is enabled. ; HKR,,RxForceDrq,0,"1" ; Only for SiS & VIA chipset. ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Parameters Section -- part of AddReg on Install ; Key values are adjustable on ADVANCED Property Sheet ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [*SMCF010.ndi.param] ; ; Infrared Transceiver Selection ; ; If AUTO [default], then driver will auto-detect at initialization, ; which will produce a single spurious Tx pulse if HP/Sharp. ; This key can be used to prevent this from happening, if desired. ; HKR,Ndi\params\RxSel,ParamDesc,,%strRXSEL% HKR,Ndi\params\RxSel,default,,"0" HKR,Ndi\params\RxSel,type,,enum HKR,Ndi\params\RxSel\enum,"0",,%strRXSEL_0% HKR,Ndi\params\RxSel\enum,"1",,%strRXSEL_1% HKR,Ndi\params\RxSel\enum,"2",,%strRXSEL_2% HKR,Ndi\params\RxSel\enum,"3",,%strRXSEL_3% HKR,Ndi\params\RxSel\enum,"4",,%strRXSEL_4% HKR,,RxSel,,"0" ; For some reason defaults are not being picked up. ; ; IrDA Minimum Turnaround Time (value in microseconds) ; HKR,Ndi\params\MinTurnTime,ParamDesc,,%strIRDATURNTIME% HKR,Ndi\params\MinTurnTime,default,,"1000" HKR,Ndi\params\MinTurnTime,type,,enum HKR,Ndi\params\MinTurnTime\enum,"500",,%strMinTurnTime_500% HKR,Ndi\params\MinTurnTime\enum,"1000",,%strMinTurnTime_1000% HKR,Ndi\params\MinTurnTime\enum,"5000",,%strMinTurnTime_5000% HKR,Ndi\params\MinTurnTime\enum,"10000",,%strMinTurnTime_10000% HKR,,MinTurnTime,,"1000" ; For some reason defaults are not being picked up. ; ; Maximum Speed ; HKR,Ndi\params\MaxSpeed,ParamDesc,,%strMAXSPEED% HKR,Ndi\params\MaxSpeed,flag,1,20,00,00,00 HKR,Ndi\params\MaxSpeed,default,,"8" HKR,Ndi\params\MaxSpeed,type,,enum HKR,Ndi\params\MaxSpeed\enum,"1",,%strMaxSpeed_1% HKR,Ndi\params\MaxSpeed\enum,"2",,%strMaxSpeed_2% HKR,Ndi\params\MaxSpeed\enum,"3",,%strMaxSpeed_3% HKR,Ndi\params\MaxSpeed\enum,"4",,%strMaxSpeed_4% HKR,Ndi\params\MaxSpeed\enum,"5",,%strMaxSpeed_5% HKR,Ndi\params\MaxSpeed\enum,"6",,%strMaxSpeed_6% HKR,Ndi\params\MaxSpeed\enum,"7",,%strMaxSpeed_7% HKR,Ndi\params\MaxSpeed\enum,"8",,%strMaxSpeed_8% HKR,,MaxSpeed,,"8" ; For some reason defaults are not being picked up. ; ; IrDA Speed enables ; ; bit=1 enables corresponding speed, 1FF is all speeds [default]) ; ; d0 = 2400 d4 = 57600 d8 = 4000000 ; d1 = 9600 d5 = 115200 ; d2 = 19200 d6 = 576000 ; d3 = 38400 d7 = 1152000 ; ; Note: Miniport will always enable 9600, ; no matter what this key says ; HKR,,SpeedEnable,,"1FF" ; For some reason defaults are not being picked up. ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Services Section ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [*SMCF010.ndi.Services] AddService=SMCIRDA,2,SMCIRDA.AddService, common.EventLog [*SMCF020.ndi.Services] AddService=SMCIRDA,2,SMCIRDA.AddService, common.EventLog [SMCIRDA.AddService] DisplayName=%*SMCF010.ServiceDesc% ServiceType=1 ; SERVICE_KERNEL_DRIVER StartType=3 ; SERVICE_DEMAND_START ErrorControl=1 ; SERVICE_ERROR_NORMAL ServiceBinary=%12%\smcirda.sys ; where the driver is ; Note: the same bin can not be used ; in multiple services LoadOrderGroup=NDIS [common.EventLog] AddReg=common.AddEventLog.reg [common.AddEventLog.reg] HKR,,EventMessageFile,0x00020000,"%%SystemRoot%%\System32\netevent.dll;%%SystemRoot%%\System32\Drivers\SmcIrda.Sys" HKR,,TypesSupported,0x00010001,7 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; File/Directory Sections ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [SysCopyFiles] smcirda.sys,,,2 ; Do not skip file ; SourceDisksNames not required if installing as part of OS [SourceDisksNames] ;1=%strDiskName%,%fileTagFile%, 1=%strDiskName%,,, ; Specifies the location of each file referencing the ; [SourceDisksNames] section [SourceDisksFiles] smcirda.sys = 1 ; smcirda.inf = 1 ; irdasmc.cat=1 ; required by WHQL in case of Win9x ; not to have, required by ChkInf in case of Win2K or later ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Localizable Strings ; ; If the INF is used for IrCC with Intel Chipset, take out "SP1" ; form DeviceDesc. ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [strings] strSMC="SMC" *SMCF010.DeviceDesc="SMC IrCC - Fast Infrared Port, SP1" *SMCF020.DeviceDesc="SMC IrCC - Fast Infrared Port, SP1" *SMCF010.ServiceDesc="SMC IrCC Miniport Device Driver" strSmcIrdaHelp="The SMC IrCC Device permits wireless communication with other devices conforming to IrDA standards using invisible infrared light." strDiskName="SMC IR_NDIS" fileTagFile="SmcIrda.Tag" ; is this still used? strRXSEL="Infrared Transceiver Type" strIRDATURNTIME="Min. Turn-Around Time" strMAXSPEED="Speed Limit" strRXSEL_0="AUTO [Default]" strRXSEL_1="IBM / Infineon / Temic" strRXSEL_2="HP" strRXSEL_3="Sharp" strRXSEL_4="VISHAY Telefunken" strMinTurnTime_500=" 0.5 mS" strMinTurnTime_1000=" 1.0 mS [Default]" strMinTurnTime_5000=" 5.0 mS" strMinTurnTime_10000="10.0 mS" strMaxSpeed_1=" 9.6 kbps" strMaxSpeed_2=" 19.2 kbps" strMaxSpeed_3=" 38.4 kbps" strMaxSpeed_4=" 57.6 kbps" strMaxSpeed_5=" 115.2 kbps" strMaxSpeed_6=" 576 kbps" strMaxSpeed_7="1.152 Mbps" strMaxSpeed_8="4 Mbps" V_CLASSNAME="Infrared Adapters"Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.