1. epson11919.exe Driver
2. language.ini File Contents

language.ini Driver File Contents (epson11919.exe)

[SYSTEM]
Language=English
font=MS Sans Serif
size=12
charset=0
MailEncLang=US-ASCII
WebEncLang=UTF-8
[MESSAGE]
142=EMP Monitor V4.10
123=&Lamp life warning
226=Replace the projection lamp.
124=&No signal
227=The projector is not receiving selected video source. Check the cable connection and make sure the connected input device is turned on.
125=Replace &Air Filter
228=Clean or replace the air filter.
126=&High-temperature warning
229=The internal temperature of the projector is rising. Remove any obstructions from around the vent and clean or replace the air filter.
115=Lamp failure at &power on
230=Lamp fails to turn on. When the fan has stopped, unplug the power cord from the projector briefly, and then plug it back in again.
116=Open lamp &cover door error (lamp error)
231=Lamp error. Check for visible defects or damage to lamp. Make sure lamp is properly installed and lamp cover door is properly seated.
117=Lamp o&ut
232=Lamp error. Check whether the lamp is damaged or the air filters clogged.
118=&Fan error
233=Fan error. Turn off and unplug projector. Contact Epson support.
119=&Sensor error
234=Sensor error. Turn off and unplug projector. Contact Epson support.
120=High int&ernal temperature error
235=High internal temperature error. Please power down normally and wait for the fan to stop. Then remove and re-insert power plug. Make sure the area around the projector is well ventilated and that the air filter is clean. Refer to user manual for proper preventive maintenance.
121=Internal (s&ystem) error
236=Internal error. Turn off and unplug projector. Contact Epson support.
122=&Other error
237=Direct Power Off function cannot be used. Invalid setting.
101=OK
104=Cancel
130=Yes
131=No
500=The communication logs exceeded 1 MB. Please delete them.
501=Insufficient disk space to save communication log files. Please remove unnecessary files to increase available disk space.
502=Cannot find the required file necessary to run EMP Monitor.\nPlease reinstall EMP Monitor.
503=Internet Explorer is not installed.\nPlease install Internet Explorer 5.0 or later.
504=Security check of the information setup file failed. Please input the correct password again.
600=&File
601=E&xit
602=&Edit
603=Ne&w
604=&Group
605=Projector (&automatic search)
606=Projector (&manual registration)
607=Select &all
608=&Edit
609=&Delete
610=Monitoring e&nabled
611=Monitoring d&isabled
612=&View
613=We&b control
614=Re&arrange
615=E&xpand
616=&Collapse
617=&Refresh (all items)
618=Re&fresh (selected items)
619=&Property
620=Pro&jector list
621=&Warning and Error Projector list
622=&Log
623=&Show
624=&Delete
625=&Tool
626=Application &lock
627=Application &unlock
628=&Environment setup
629=Mail notification &function
630=&Plug-in
631=&Help
632=&Version information
634=&Refresh
143=Refresh
144=Select all
145=Show Warning and Error projector list
146=Power On
147=Power Off
148=Switch source Computer1
149=Switch source Computer2
150=Switch source BNC
151=Switch source S-Video
152=Switch source Video
153=Switch source DVI, HDMI
154=Switch source D-Video
155=Switch source EasyMP
340=Warning or Error has occurred.
633=&Open the main screen
505=Cannot open additional Group Properties because the maximum number (10) of Group Properties is already open.
506=Cannot open additional Projector properties because the maximum number (10)  of Projector properties is already open.
507=OK to delete %s?
508=OK to delete this %s and all groups of projectors included in the %s?
261=Show projector list
181=Create new group
182=Edit group 
105=&Group name
107=Display &icon
108=&Parent group
112=&Monitor
102=&Register
103=&Change
191=Create new projector (automatic registration)
110=Projector &name
111=IP &address
192=&Search
193=&Edit
202=Create new projector (automatic search)
201=Create new projector (manual registration)
203=Edit projector
204=&Search
205=Use Serial <-> &TCP/IP conversion adaptor.
206=P&ort Number
207=Pass&word
509=IP address is invalid. Please enter valid IP address.
510=There is no port number entered. Please enter a port number.
511=The port number is invalid. Please enter a valid port number.
512=A projector has been detected.
513=The projector cannot be found.
514=Projector names cannot consist of only numbers.
515=The specified projector is already registered.
516=Monitor Password is incorrect. Please enter the correct password.
221=Group properties (%s)
222=Warning and Error Projector list
223=Type
106=&Display name
224=Power
113=Lamp Hours
225=Source
114=Error information
252=Projector properties (%s)
271=Environment setup
272=Update &interval
273=minutes
274=Register at &startup
275=Resident in the &task tray
276=Change the application &lock password
277=&Old password
278=&New password
279=New password (&confirm)
517=Please enter update interval.
518=The old password is incorrect. Enter the old password one more time.
519=Password does not match. Please enter new password again.
291=Application unlock
520=Application unlock password is incorrect. Please enter correct password.
521=Failed to unlock the application 
331=Version information
332=EMP Monitor Version 4.10
333=Copyright (C) SEIKO EPSON CORPORATION 2005-2006.
301=Set mail notification function
302=Mail notification &function
303=On
304=Off
305=&Method for sending mail
306=SMTP
307=MAPI
308=&SMTP server IP address
309=Sender mail &address
310=Recipient mail address &1
311=Recipient mail address &2
312=Recipient mail address &3
323=Notification event
522=Please enter an SMTP server address.
523=The SMTP server address is invalid. Please enter a valid address.
524=Please enter an SMTP server port number.
525=The SMTP server port number is invalid. Please enter a valid port number.
526=Please enter a destination email notification address
360=[%s] Projector warning/error notification
361=The following warning/error occurred on %s(%s).\n\n%s\n\nImmediately check the projector.
321=Set mail notification event(%s)
322=Set notification event
527=Cannot monitor all projectors because of the large amount of projectors to be monitored.
132=Communication error
528=Failed to communicate with the projector. Please restart the projector.
133=Other errors
529=The power to the projector may not be turned on, or there may be no projectors available.
109=None
127=Network error (&TCP connection error)
128=Network error (ESC/&VP.net communication error)
129=Network error (&monitor password authentication error)
535=An internal error has occurred.
533=Please wait.
534=Shutting down EMP Monitor. Please wait.
135=Unknown error
542=OK to delete?
536=Version of information setup file is incorrect. Shutting down EMP monitor.
537=Information setup file is corrupt. Shutting down EMP monitor.
538=There are already %d entries registered.No more items can be registered.
539=Failed to update the projector information.
540=Failed to create a projector (automatic registration) editing dialog.
541=Failed to create a mail notification event dialog.
543=There are more than %d entries in the information setup file. Shutting down EMP monitor.
370=Unknown IP address
544=Please enter sender's email address.
545=The specified group has been registered.
546=The specified projector has been registered.
547=The "EMP Monitor.dat" file could not be stored.
380=Group name
381=Display name
382=Projector name
383=IP address
384=Lamp failure at power on
385=Open lamp cover door error (lamp error)
386=Lamp out
387=Fan error
388=Sensor error
389=High internal temperature error
390=Internal (system) error
391=Other error
392=Lamp life warning
393=No signal
394=Replace Air Filter
395=High-temperature warning
396=Network error (TCP connection error)
397=Network error (ESC/VP.net communication error)
398=Network error (monitor password authentication error)
399=Recipient mail address 1
400=Recipient mail address 2
401=Recipient mail address 3
402=Notification &event
403=Notification e&vent
404=Notification eve&nt
194=Specify an address &range and search.
195=S&tart address
196=E&nd address
548=Please enter starting address.
549=Please enter ending address.
550=Starting address is invalid. Please enter a valid address.
551=Ending address is invalid. Please enter a valid address.
552=Specified IP address search range is invalid. Please enter a valid range.
553=The search may take time due to the extended search range. Do you want to start the search?
450=Information
460=Option
461=Display items
462=&Type
463=&Group name
464=Projector &name
465=&Display name
466=IP &address
467=&Power
468=&Lamp Hours
469=&Source
470=Te&mperature level
471=Des&cription
472=&Error information
208=D&escription
209=Monitor Pass&word
136=Temperature level
137=Description
139=Version information
292=T&emperature level display group view
293=L&amp schedule notification
294=Lo&g output
405=No Air Filter
406=Low Air Flow
407=Air Flow Sensor Err.
238=Install the air filter.
239=The air filter is clogged.\nClean or replace the air filter.
240=Air filter malfunction.\nContact service center for repair.
635=&Grouping view
636=&Detail list view
637=&Option
554=Please select one or more display items.
314=Time
408=Temperature level
409=Description
164=No Ai&r Filter
165=Lo&w Air Flow
166=A&ir Flow Sensor Err.
362=[%s] Projector recovery notification
363=The following %s (%s) warning/error has been recovered.\n\n%s
364=[%s] Projector warning/error recovery notification
365=The following warning/error occurred on %s(%s).\n\n%s\n\nThe following %s (%s) warning/error has been recovered.\n\n%s\n\nImmediately check the projector.
366=EMP Monitor log
367=Previous page
368=Next page
369=Duplicate IP address. Monitoring has been disabled.
555=Number of communication log files exceeds maximum limit. Please delete some communication logs.
556=Failed to record as the communication log has been filled. Please delete some communication logs.