1. EZ_2000.zip Driver
2. README File Contents

README Driver File Contents (EZ_2000.zip)

								MAY 1994

	   Release Note for EZ-2000 series Ethernet Card
	==========================================================

Thank you for purchasing the EZ-2000 series Ethernet cards.
The driver programs in this diskette support all EZ-2000 series Ethernet
cards.

********************************************************************
*								   *
*  EZ-2000 series Ethernet cards do not have any on-board jumpers  *
*  or switches. All the hardware settings can be specified	   *
*  through our SETUP.EXE program. Please run SETUP.EXE		   *
*  program toset up and test the hardware configuration.	   *
*								   *
********************************************************************

	EZ-2000 series Ethernet Card Setup/Diagnostic program
	====================================================
The SETUP.EXE program (Setup/Diagnostic) lets you configure the EZ-2000
hardware settings, and test the state and cable connection of the card.

To run the program, insert the EZ-2000 driver program diskette in drive
'A' and do the following:

	> SETUP 	     --run the SETUP.EXE program
	or
	> SETUP /D	     --run the SETUP.EXE with parameter /D
			       this parameter lets you setup the EZ-2000 by
			       reading SETUP.DAT file. This way, you can
			       quickly configure your card without going
			       through the menus.


Sample of SETUP.DAT
======================

Connector Type	 UTP
I/O Base Address 0x300
Interrupt Number 3
ROM Size	 16K
ROM Address	 0xd000


NOTE 1: The keywords must appear in the exact format as listed in the
	parameter file table.

	Only those keywords persent in the SETUP.DAT file will be
	written to the EZ-2000 NIC.

NOTE 2: If there no entries for 'ROM Size' and 'ROM Address', Boot ROM
	will be disabled.

	       EZ-2000 Series Adapter parameter file table
	 +----------------------+----------------------------------+
	 | KEYWORDS		|  AVAILABLE SELECTIONS 	   |
	 +----------------------+----------------------------------+
	 | Connector Type	|  UTP, BNC,			   |
	 +----------------------+----------------------------------+
	 | IRQ			|  *3, 4, 5, 9, 10, 11, 12, 15	   |
	 +----------------------+----------------------------------+
	 | I/O Base		|  240H, 280H, 2C0H,		   |
	 | Address		|  *300H, 320H, 340H, 360H	   |
	 +----------------------+----------------------------------+
	 | Boot ROM Sizes	|  Base Memory			   |
	 +----------------------+----------------------------------+
	 | 8K/16K		|  C400H			   |
	 |			|  CC00H			   |
	 |			|  D400H			   |
	 |			| *DC00H			   |
	 |			|				   |
	 | 32K			|  C000H			   |
	 |			|  C800H			   |
	 |			|  D000H			   |
	 |			|  D800H			   |
	 +----------------------+----------------------------------+
	  *default value

Menu Options
============

1.  SETUP lets you configure the hardware settings of EZ-2000.
    You have the option to view/change :

		 <1> Node ID
		 <2> Bus Mode
		 <3> Card Type
		 <4> Connector Type
		 <5> I/O Base Address
		 <6> Interrupt Number
		 <7> Remote Boot ROM Size
		 <8> Base Memory Address

2.  DIAGNOSTIC lets you diagnose the state and cable connections of EZ-2000.

****************************************
* THE DRIVER PROGRAMS IN THIS DISKETTE *
****************************************

The driver programs in this diskette is organized in the following manner.
Each directory contains a README.DOC file which provides you with detailed
installation instructions:

Directory	  Contents
----------    ---------------------------------------------------------
\3COM	      3Com 3+ Share Driver program
\AT&TUNIX     AT&T UNIX Driver program
\NDIS	      NDIS Driver program
\NDIS3	      NDIS V.3.X Driver program
\NETWARE      Novell NetWare version 3.x, 4.x(ODI driver included)
\NEXOS	      NEXOS workstation driver program
\PCNFS	      Sun MicroSystems PC-NFS Driver Program
\PCTCP	      FTP PC/TCP Driver Program
\SCOUNIX      SCO UNIX driver program (TCPIP V1.1X & V1.2X included)