=========================================================
Digital PCI Fast Ethernet Adapter Diagnostic Program
=========================================================
This Diagnostic program contains the following functions:
1. Adapter Information
2. Diagnostic Tests
(1). Adapter Information
Display Card information, including
Chip ID 0900
Node ID 00 E0 06 XX XX XX
Bus Mode PCI 32-bit
Media type 100 Half Duplex
I/O Base Address 6000
Interrupt Number 0B
(2). Diagnostic Tests
Controller Loopbacks : Test MAC internal loopback mode.
External Loopbacks : Test external loopback through loopback
connector.
(Note) You should have a loopback connector. You can make such
a connector by connecting pin 1 and pin 3, pin 2 and
pin 6.
Send Magic Packet : Specify Destination Address and Send a
magic packet to wake-up other PC.
Send Wake-up Frame : Specify wake-up frame to wake-up other
PC.
Set Wake-up Event : Set wake-up event to Digital Data LAN adapter.
(Note) After you Set wake-up event, you can turn off the power
by press power button. Then wait for wake-up event.
=========================
Steps To test wake-on LAN
=========================
0. Connect the 3-pin Wake-on-LAN header to M/B.
1. Test Wake-up frame
PC1 that will be waked up PC2 that will wake up PC1
(This M/B should support
Ring-in or Wake-on-LAN)
----------------------------- --------------------------
a. Select "Set wake-up Event" a. Wait until PC1 is ready
b. Set wake-up Frame and b. Send wake-up frame
byte mask
c. Power off
d. Wait for PC2 to wake me
up
2. Test Magic Packet
PC1 that will be waked up PC2 that will wake up PC1
----------------------------- -------------------------
a. Select "Set wake-up Event" a. Wait until PC1 is ready
b. Set Magic Packet b. Send Magic Packet
c. Power off (Destination Address
d. Wait for PC2 to wake me must be PC1 MAC addr)
up
3. Test Link On
PC1 that will be waked up
-----------------------------
a. Do not Connect Cable
(Force Link Off)
b. Select "Set Wake-Up Event"
c. Select "Link On"
d. Power off
e. Plug a loopback connector.
(Force link-on Event)
4. Test Link Off
PC1 that will be waked up
-----------------------------
a. Plug a loopback connector.
(Force Link On)
b. Select "Set Wake-Up Event"
c. Select "Link Off"
d. Power off
e. Unplug the loopback connector.
(Force link-off Event)
=========================
How to Set wake-up Frame
=========================
Digital FN100 supports 3 wake-up frames.
Each Wake-up frame is up to 128 bytes.
Frame 1: 00XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
BitMask: 1XXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Fill frame with any pattern you want.
Each '1' in Byte mask means byte you want to match.
Ex.
Frame X: 00E00600902212345678XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
BitMask: 0000001111XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
This means you want to match byte 6 to 9 -- 12 34 56 78
Any received packet that matches byte 6 to 9 will be a wake-up
frame.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.