PATHWAY.TXT Driver File Contents (AcctonEN2212PCMCIACardEthernetDrivers.exe)

		 Accton EN2212 Ethernet PCMCIA Adapter
	   NDIS Driver for Wollongong Pathway Access Installation
	  ========================================================

The driver ETHPCM.DOS contained in directory \NDIS\DOS is used with
Accton Ethernet PCMCIA adapters in the Wollongong Pathway Access
environment.

This driver conforms to the Network Driver Interface Specification
(NDIS) 2.0 defined by Microsoft/3Com.


1. INSTALLATION PROCEDURE
==========================

  a. NDIS driver Installation Procedure:

    1. Insert your copy of Pathway Drivers diskette into drive A. Enter:

       C:\>A:

    2. To install the software, enter:

       A:\> pwinstal C:

       where C: is the hard drive letter (you could also use D:, E:, and
       so on) that you intend to install your Pathway software on.
       The PWINSTAL program automatically installs the driver software in
       a directory named \PATHWAY on the drive you specified.

       The installation is complete when you receive the following
       message: "The Pathway Drivers have been copied successfully.  Refer
       to documentation to complete driver installation."

    3. Insert the driver diskette in drive A and copy the NDIS driver to the
       subdirectory where you installed the Pathway software:

       A:\> Copy A:\NDIS\DOS\ETHPCM.DOS C:\PATHWAY

    4. Edit the C:\CONFIG.SYS file to contain the following entries:

       DEVICE=C:\PATHWAY\ACCOPEN.EXE /int=5 /port=300
       DEVICE=C:\PATHWAY\PWTCP.SYS
       DEVICE=C:\PATHWAY\PROTMAN.EXE/I:C:\PATHWAY
       DEVICE=C:\PATHWAY\ETHPCM.DOS

       At the same time copy ACCOPEN.EXE from the driver diskette to
       the \PATHWAY directory.

    5. Use a text editor to create a PROTOCOL.INI file in C:\PATHWAY
       with the following section:

       [EN2212]
       DriverName = ETHPCM$

    6. The startup batch file - AUTOEXEC.BAT should have the following entries
       in the order shown:

       path=c:\pathway
       ndis [-d:#]
       pwbind

       where the -d option is used when accessing a specific module number
       within PROTOCOL.INI.  In your PROTOCOL.INI file, a line enclosed by
       square brackets designates the beginning of a new module.  Each module
       is referred to by a hexadecimal number.	The first module is module
       number one. The second is module number two, and so on.

  b. Pathway Kernel Installation Procedure

    1. Insert the Pathway Kernel diskette in drive A.  Enter:

       C:\>A:

    2. To install the software, enter:

       A:\> pwinstal C:

       where C: is the hard drive letter (you could also use D:, E:, and
       so on) that you intend to install your Pathway software on.
       The PWINSTAL program automatically installs the driver software
       in a directory named \PATHWAY on the drive you specified.

       Diskette copying is complete when you see the following message:
       "Pathway Kernel files have been copied successfully.  Reboot and refer
       to the documentation to complete kernel installation."

     3. Remove the diskette from drive A: and reboot your PC by pressing
	<Ctrl>, <Alt>, and <Del> at the same time.

     4. Change current directory to \PATHWAY.

     5. Run the CUSTOM program to set or change the following parameters:

       . The Internet address
       . The subnet mask (if your network has subnetworks)
       . The gateway address (if you are communicating with hosts outside your
	 local network)

     6. Remove the diskette from drive A: and reboot your PC by pressing
	<Ctrl>, <Alt>, and <Del> at the same time.

     7. Enter the following command to load the Kernel:

       C:\PATHWAY> PWTCP

     8. Test your PC by using the PING program:

       C:\PATHWAY> PING hostname

       where hostname is the official name, alias, or Internet address of a
       host on your network that you expect to be able to communicate with.


-- THE END --

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web2, load: 0.72