Samsung PCI Network Driver Installation Guide for NetWare 3.x/4.x Client
========================================================================
Samsung PCI Network Driver Installation for NetWare 3.x Client
==============================================================
This document describes how to install Novell NetWare 3.x ODI client
software to work with the Samsung PCI Network adapter.
1. Create a directory named NETWARE on your C drive.
2. Insert the NetWare WSGEN disk that came with NetWare 3.x disk into drive A.
3. Copy the following three files to the NETWARE directory on your C drive:
LSL.COM
IPXODI.COM
NETX.COM
4. Remove the NetWare WSGEN disk from drive A.
5. Insert the Samsung PCI Network Driver Disk into drive A.
6. Copy NET.CFG and SE100ODI.COM to the NETWARE directory on your C drive.
7. Check your CONFIG.SYS file to make sure that the following line appears:
DEVICE=C:\DOS\SETVER.EXE
assuming that \DOS is the directory where you have all your DOS
files including SETVER.EXE.
8. Remove the Samsung PCI Network Driver Disk from drive A.
9. Restart your computer.
10. To run NetWare, type the following four commands (in the following
sequence) at the C:\NETWARE prompt:
LSL
SE100ODI
IPXODI
NETX
11. Change to the network drive (usually F) and login to your network.
NOTES1:
=======
1. NETX.EXE (dated 930217) will work with DOS 6.0 or lower version only.
You will need NETX.EXE (dated 931117) to work with DOS 6.22.
2. If you choose to use the Netware Client Install program, follow the
instructions for Netware 4.x Client Installation document.
3. Remove the line LASTDRIVE=Z from your CONFIG.SYS file, if it exists.
4. A sample NET.CFG file is shown below:
Link Driver SEC100
RX_BUFFERS 64
; LINE_SPEED 100
TX_THRESHOLD 1500
; NODE ADDRESS 222222222222
FRAME Ethernet_802.3
PROTOCOL IPX 0 Ethernet_802.3
; FULL_DUPLEX
Samsung PCI Network Driver Installation for NetWare 4.x Client
==============================================================
This document describes how to install the Samsung PCI Network driver for
the Novell NetWare version 4.x client software.
1. Run the NetWare Client Install program that comes with NetWare 4.x.
Follow the instructions for the first three steps of the NetWare
Client Install program as required.
2. At step 4, press Enter to install the Samsung PCI driver for your adapter.
3. When prompted, insert the Samsung Driver Disk into drive A (or B) and
type the following:
A:\NOVELL\CLIENT\DOS <ENTER>
4. The Network Board window appears. Select Samsung PCI Ethernet Adapter and
press Enter.
5. In the "Network Board" window, press Enter to continue with the NetWare
installation.
7. When prompted, insert the appropriate NetWare Client Install disk.
8. Press Enter to exit to the DOS prompt.
9. Restart the computer.
10. To run NetWare, type the following commands (in sequence) at the DOS
prompt:
LSL
SE100ODI
IPXODI
VLM
11. Change to the network drive (usually F), and login to your network.
NOTES2:
=======
Make sure your NET.CFG file is setup properly. A sample file is shown below:
Link Support
Protocol
Bind SEC100
Link Driver SEC100
RX_BUFFERS 64
; LINE_SPEED 100
TX_THRESHOLD 1500
; NODE ADDRESS 222222222222
FRAME Ethernet_802.3
PROTOCOL IPX 0 Ethernet_802.3
; FULL_DUPLEX
NetWare DOS Requester
FIRST NETWORK DRIVE = F
NETWARE PROTOCOL = NDS BIND
NOTES3:
=======
Following is the description of keywords.
RX_BUFFERS -- Number of receive buffer in 256 bytes. Valid
range from 32 to 128 with 64 (meaning 16K of rx
buffer) as the default.
LINE_SPEED -- Line speed selection. Can be either 10 or 100.
If this keyword is absent, Autonegotiation mode is
used (recommended).
TX_THRESHOLD -- Transmit threshold. Valid range from 0 to
1500 with 1500 as the default.
NODE ADDRESS -- Node ID override. If it is absent, driver will
use the one in the serial eeprom (recommended).
FULL_DUPLEX -- Full duplex mode. If absent, half duplex mode.
This keyword is valid only when LINE_SPEED keyword
is specified.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.