Standard Microsystems Corporation
SMC8022T EZ PCMCIA 10Base-T Adapter
SMC8022BT EZ PCMCIA Combo Adapter for
NetWare Server, Netware client for DOS/WIN
======================================================================
IMPORTANT NOTE:
***** Before you install the driver in server and client, *****
***** you have to enable the EZ PCMCIA Adatper first. *****
***** Use "SMCOPEN.EXE /int=x /port=xxx " located *****
***** in the root of the driverDisk to activate the *****
***** card first (In DOS prompt). *****
Novell NetWare V3.12 AND V4.10 Server Driver Installation
=========================================================
1. Things You Need
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Before you start with the installation process make sure you have
the following :
a) Hardware Driver Disk
b) Novell NetWare Version 3.12 AND V4.10 System Diskette
2. How To Install O.S. Driver
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
a) Insert the SMC EZ PCMCIA 10Base-T Adapter
Driver Disk into drive A
and check the contents of subdirectory \NETWARE
It should contain the following file :
SMC8022.LAN ÄÄ Novell NetWare V3.12 Server Driver
b) Copy the contents of the Novell NetWare 386 Version
3.11 System Diskette into your NetWare 386 server
station hard disk. Please refer to your Novell
NetWare 386 Installation Manual for details.
c) Copy the SMC8022.LAN file from the Hardware Driver Disk
into the NetWare server station hard disk.
d) Run SERVER.EXE on the server station. Several NetWare
messages will be shown on-screen.
e) At the NetWare prompt (indicated by a colon), run
the driver program, type the following line if using one adapter:
: LOAD [d:]SMC8022 Frame=frame_type <Enter>
or type the following line if more adapters are used:
: LOAD [d:]SMC8022 SLOT=board# Frame=frame_type
where board# starts 0 to 4, because number of adapters supported is 4
(You can reference the autoexec.ncf example included in the floppy)
LOAD SMC8022 SLOT=0 FRAME=Ethernet_802.3
BIND IPX SMC8022
LOAD SMC8022 SLOT=0 FRAME=Ethernet_802.2
BIND IPX SMC8022
LOAD SMC8022 SLOT=0 FRAME=Ethernet_SNAP
BIND IPX SMC8022
LOAD SMC8022 SLOT=0 FRAME=Ethernet_II
BIND IPX SMC8022
f) Bind IPX with LAN driver, at the Netware server prompt,
type :
:BIND IPX SMC8022 <Enter>
After pressing <Enter> the computer prompts you for
the Network Number. For details on how to assign this
number, please consult your NetWare 386 Installation
Manual.
If problems occur during the binding process, your
screen will prompt you with error messages. Please
refer to your NetWare 386 manual for details on these
messages. The LAN driver installation is completed
when you see the following message on-screen :
IPX LAN Protocol bound to NE Mode vx.xxRxx (yymmdd).
Novell NetWare V4.11 Server Driver Installation
===============================================
Requirements
------------
Make sure you have the following:
1. Driver Diskette
Installation Procedure
----------------------
1. Insert the Driver Diskette that comes with the package
into drive A: and check the contents of the
subdirectory \NETWARE. It should have
the following files:
SMC8022.LAN ----> your Novell NetWare v4.x Server Driver
SMC8022.LDI ----> your Novell NetWare v4.x Server Driver
configuration file
2. At the NetWare prompt (indicated by the Server name), run
the INSTALL.NLM program by typing:
server name: LOAD INSTALL <Enter>
3. Follow screen instruction to complete the process. Respond
to prompts displayed on the screen. Select the following
items in the order given below. Press <Enter> to confirm
each choice:
Maintenance/Selective Install <Enter>
LAN Driver Options (Configure/Load/...) <Enter>
4. Press the <Ins> key to insert other drivers you wish
to install.
5. Press <F3> to display the driver loading path as follows:
A:\NETWARE <Enter>
6. The SMC8022.LAN will appear as an item under the
"Select a LAN Driver" menu. Choose the correct board number
and Select it to load the driver and start the binding
process. This will allow you to load and bind all 4 frame
types supported by NetWare.
7. Next time you reboot your NetWare 4.11 server, do so by
following steps 2 to 4 above.
Notes about the Novell v4.x and the v3.1x drivers
--------------------------------------------------
Installation Procedure
----------------------
1. The NetWare v4.x and v3.11 drivers have different
architectures. When using NetWare v4.x, you should
load the NBI.NLM ,MSM.NLM and ETHERTSM.NLM modules
before loading server driver SMC8022.LAN.
2. SMC8022.LAN is your server driver for NetWare v4.x. When
loading SMC8022.LAN, it will check whether or not
these three modules (NBI.NLM ,MSM.NLM and ETHERTSM.NLM) have been
loaded. If not, it will load them automatically.
3. After the SMC8022.LAN is loaded, type the "MODULES" command to
view and confirm that the additional modules, MSM.NLM and
ETHERTSM.NLM loaded.
4. The default frame type SMC8022.LAN binding for NetWare v4.x
is Ethernet_802.2 and not Ethernet_802.3.
5. If you have any trouble to load NLM modules , Please refer autoexec.ncf
in each directory.
Novell Netware Client for DOS32 installation
============================================
1.> If you have completed installed the Netware Client 32 for DOS,
all you have to do is to modify STARTNET.BAT. Please see the
sample STARTNET.BAT below.
if not, Please follow the next step 2 - step 7.
Sample STARTNET.BAT is as follow:
SET NWLANGUAGE=English
C:\NOVELL\CLIENT32\NIOS.EXE
LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
LOAD C:\NOVELL\CLIENT32\CMSM.NLM
LOAD C:\NOVELL\CLIENT32\ETHERTSM.NLM
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=ETHERNET_802.2 PnP_Mode=1 SLOT=10001
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=Ethernet_802.3 PnP_Mode=1 SLOT=10001
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=Ethernet_II PnP_Mode=1 SLOT=10001
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=Ethernet_SNAP PnP_Mode=1 SLOT=10001
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=ETHERNET_802.2 PnP_Mode=1 SLOT=10002
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=Ethernet_802.3 PnP_Mode=1 SLOT=10002
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=Ethernet_II PnP_Mode=1 SLOT=10002
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=Ethernet_SNAP PnP_Mode=1 SLOT=10002
LOAD C:\NOVELL\CLIENT32\IPX.NLM
LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM
C:
SET NWLANGUAGE=English
C:\NOVELL\CLIENT32\NIOS.EXE
LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
LOAD C:\NOVELL\CLIENT32\CMSM.NLM
LOAD C:\NOVELL\CLIENT32\ETHERTSM.NLM
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=ETHERNET_802.2 port=300
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=Ethernet_802.3 port=300
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=Ethernet_II port=300
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=Ethernet_SNAP port=300
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=ETHERNET_802.2 port=2a0
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=Ethernet_802.3 port=2a0
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=Ethernet_II port=2a0
LOAD C:\NOVELL\CLIENT32\NW41.LAN FRAME=Ethernet_SNAP port=2a0
LOAD C:\NOVELL\CLIENT32\IPX.NLM
LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM
C:
2.> Run INSTALL.EXE from Netware DOS 32 diskette 1 (or from Netware
4.11 CD). When the product manual appears, mark the
"Netware Client 32 for DOS" item, then press <Enter>.
3.> Select "OTHER DRIVERS" item from "32-bit Network Board Drivers" menu,
then press <Enter>.
4.> select "USER SPECIFIED 32 BIT DRIVER." press <Enter>.
5.> Insert SMC EZ PCMCIA 10Base-T Adapter
Driver Diskette into your floppy
diskette drive,then specify the driver path like A: or B:.
6.> Following instructions to complete the Client32 for DOS software
installation.
7.> Reboot your machine.
Novell Netware Client for Microsoft Windows 3.X installation
============================================================
Please refer to Content B.), in step 2, mark "Netware Client 32 for DOS"
and "Client 32 for Windows"; in step 5, specify the driver path like
A:\LANDRV32 or B:\LANDRV32. then following step 3..7
to complete the installation.
TRADEMARKS
==========
All trademarks or brand names mentioned are trademarks of their
respective companies.
==End of File ==
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.