[00] MAIN = No error [02] MAIN = not ready 0481 = Unit is offline. 0483 = Not ready; the front door is open. [04] MAIN = hardware 1581 = Pick error. 1583 = Put error. 1584 = Mechanical problem: Stalled while picking from drive. 3B82 = Cannot close drive door. 3B87 = Cannot open drive door. 4082 = Flash memory CHECKSUM error. 4090 = Normal force position overflow 4095 = Cartridge destination or PUT error. 40A1 = X-axis stuck. 40A2 = X-axis HOME failure. 40A3 = X-axis MOVE timed out 40A4 = X-axis controller failure; wrap error. 40A7 = Motor controller reset failure. 40A8 = X-axis servo busy bit set. 40B1 = X-axis position error. 40B2 = X-HOME failure. 40B3 = Move time-out error. 40B4 = X WRAP error. 40B6 = X-Axis home with cartridge failure 40B8 = Servo busy bit set, command error. 40C1 = Z-axis stuck. 40C2 = Z-axis HOME failure 40C3 = Z-axis MOVE timed out. 40C4 = Z-axis controller failure, wrap error. 40C8 = Z-axis servo busy bit set. 40CA = Read cartridge labels timed out. 40D1 = SCIE Initialization Error 40D7 = SCIE Extend Error 40D8 = SCIE Retract Error 8017 = Barcode retries exceeded limits. 8400 = Internal software error. [05] MAIN = illegal request 3B80 = User intervention required. 3B83 = Bad drive response. 3B84 = Destination drive door is closed 3B85 = Destination cannot be cartridge handler. 3B86 = Source cannot be cartridge handler. 3B87 = Data cartridge stuck in drive. 40E1 = SCIE Destination Full 40E4 = SCIE Failed Extend / Retract 40EO = SCIE Source Empty 8003 = No source magazine. 8004 = No destination magazine. 8005 = No source drive. 8006 = No destination drive. [06] MAIN = unit attention [0B] MAIN = aborted command 4300 = SCSI message error. 3F80 = Flash firmware upgrade error: Unable to erase. 3F81 = Write firmware, incomplete code data. 3F84 = Flash firmware upgrade error: Unable to program. 3F86 = Firmware upgrade error: Flash CHECKSUM error. [SCSI2] 0000 = NO ADDITIONAL SENSE INFORMATION 0001 = FILEMARK DETECTED 0002 = END-OF-PARTITION/MEDIUM DETECTED 0003 = SETMARK DETECTED 0004 = BEGINNING-OF-PARTITION/MEDIUM DETECTED 0005 = END-OF-DATA DETECTED 0006 = I/O PROCESS TERMINATED 0011 = AUDIO PLAY OPERATION IN PROGRESS 0012 = AUDIO PLAY OPERATION PAUSED 0013 = AUDIO PLAY OPERATION SUCCESSFULLY COMPLETED 0014 = AUDIO PLAY OPERATION STOPPED DUE TO ERROR 0015 = NO CURRENT AUDIO STATUS TO RETURN 0016 = OPERATION IN PROGRESS 0017 = CLEANING REQUESTED 0018 = ERASE OPERATION IN PROGRESS 0019 = LOCATE OPERATION IN PROGRESS 001A = REWIND OPERATION IN PROGRESS 001B = SET CAPACITY OPERATION IN PROGRESS 001C = VERIFY OPERATION IN PROGRESS 0100 = INDEX/SECTOR SIGNAL 0200 = NO SEEK COMPLETE 0300 = PERIPHERAL DEVICE WRITE FAULT 0301 = NO WRITE CURRENT 0302 = EXCESSIVE WRITE ERRORS 0400 = LOGICAL UNIT NOT READY, CAUSE NOT REPORTABLE 0401 = LOGICAL UNIT IS IN PROCESS OF BECOMING READY 0402 = LOGICAL UNIT NOT READY, INITIALIZING COMMAND REQUIRED 0403 = LOGICAL UNIT NOT READY, MANUAL INTERVENTION REQUIRED 0404 = LOGICAL UNIT NOT READY, FORMAT IN PROGRESS 0405 = LOGICAL UNIT NOT READY, REBUILD IN PROGRESS 0406 = LOGICAL UNIT NOT READY, RECALCULATION IN PROGRESS 0407 = LOGICAL UNIT NOT READY, OPERATION IN PROGRESS 0408 = LOGICAL UNIT NOT READY, LONG WRITE IN PROGRESS 0409 = LOGICAL UNIT NOT READY, SELF-TEST IN PROGRESS 040A = LOGICAL UNIT NOT ACCESSIBLE, ASYMMETRIC ACCESS STATE TRANSITION 040B = LOGICAL UNIT NOT ACCESSIBLE, TARGET PORT IN STANDBY STATE 040C = LOGICAL UNIT NOT ACCESSIBLE, TARGET PORT IN UNAVAILABLE STATE 0410 = LOGICAL UNIT NOT READY, AUXILIARY MEMORY NOT ACCESSIBLE 0411 = LOGICAL UNIT NOT READY, NOTIFY (ENABLE_SPINUP) REQUIRED 0500 = LOGICAL UNIT DOES NOT RESPOND TO SELECTION 0600 = NO REFERENCE POSITION FOUND 0700 = MULTIPLE PERIPHERAL DEVICES SELECTED 0800 = LOGICAL UNIT COMMUNICATION FAILURE 0801 = LOGICAL UNIT COMMUNICATION TIME-OUT 0802 = LOGICAL UNIT COMMUNICATION PARITY ERROR 0803 = LOGICAL UNIT COMMUNICATION CRC ERROR (ULTRA-DMA/32) 0804 = UNREACHABLE COPY TARGET 0900 = TRACK FOLLOWING ERROR 0901 = TRACKING SERVO FAILURE 0902 = FOCUS SERVO FAILURE 0903 = SPINDLE SERVO FAILURE 0904 = HEAD SELECT FAULT 0A00 = ERROR LOG OVERFLOW 0B00 = WARNING 0B01 = WARNING - SPECIFIED TEMPERATURE EXCEEDED 0B02 = WARNING - ENCLOSURE DEGRADED 0C00 = WRITE ERROR 0C01 = WRITE ERROR RECOVERED WITH AUTO REALLOCATION 0C02 = WRITE ERROR - AUTO REALLOCATION FAILED 0C03 = WRITE ERROR - RECOMMEND REASSIGNMENT 0C04 = COMPRESSION CHECK MISCOMPARE ERROR 0C05 = DATA EXPANSION OCCURRED DURING COMPRESSION 0C06 = BLOCK NOT COMPRESSIBLE 0C07 = WRITE ERROR - RECOVERY NEEDED 0C08 = WRITE ERROR - RECOVERY FAILED 0C09 = WRITE ERROR - LOSS OF STREAMING 0C0A = WRITE ERROR - PADDING BLOCKS ADDED 0C0B = AUXILIARY MEMORY WRITE ERROR 0C0C = WRITE ERROR - UNEXPECTED UNSOLICITED DATA 0C0D = WRITE ERROR - NOT ENOUGH UNSOLICITED DATA 0D00 = ERROR DETECTED BY THIRD PARTY TEMPORARY INITIATOR 0D01 = THIRD PARTY DEVICE FAILURE 0D02 = COPY TARGET DEVICE NOT REACHABLE 0D03 = INCORRECT COPY TARGET DEVICE TYPE 0D04 = COPY TARGET DEVICE DATA UNDERRUN 0D05 = COPY TARGET DEVICE DATA OVERRUN 0E00 = INVALID INFORMATION UNIT 0E01 = INFORMATION UNIT TOO SHORT 0E02 = INFORMATION UNIT TOO LONG 0F00 = RESERVED 1000 = CRC OR ECC ERROR 1100 = UNRECOVERED READ ERROR 1101 = READ RETRIES EXHAUSTED 1102 = ERROR TOO LONG TO CORRECT 1103 = MULTIPLE READ ERRORS 1104 = UNRECOVERED READ ERROR - AUTO REALLOCATE FAILED 1105 = UNCORRECTABLE ERROR 1106 = UNRECOVERED ERROR 1107 = DATA RESYNCHRONIZATION ERROR 1108 = INCOMPLETE BLOCK READ 1109 = NO GAP FOUND 110A = MISCORRECTED ERROR 110B = UNRECOVERED READ ERROR - RECOMMEND REASSIGNMENT 110C = UNRECOVERED READ ERROR - RECOMMEND REWRITE THE DATA 110D = DE-COMPRESSION CRC ERROR 110E = CANNOT DECOMPRESS USING DECLARED ALGORITHM 110F = ERROR READING UPC/EAN NUMBER 1110 = ERROR READING ISRC NUMBER 1111 = READ ERROR - LOSS OF STREAMING 1112 = AUXILIARY MEMORY READ ERROR 1113 = READ ERROR - FAILED RETRANSMISSION REQUEST 1200 = ADDRESS MARK NOT FOUND FOR ID FIELD 1300 = ADDRESS MARK NOT FOUND FOR DATA FIELD 1400 = RECORDED ENTITY NOT FOUND 1401 = RECORD NOT FOUND 1402 = FILEMARK OR SETMARK NOT FOUND 1403 = END-OF-DATA NOT FOUND 1404 = BLOCK SEQUENCE ERROR 1405 = RECORD NOT FOUND - RECOMMEND REASSIGNMENT 1406 = RECORD NOT FOUND - DATA AUTO-REALLOCATED 1407 = LOCATE OPERATION FAILURE 1500 = RANDOM POSITIONING ERROR 1501 = MECHANICAL POSITIONING ERROR 1502 = POSITIONING ERROR DETECTED BY READ OF MEDIUM 1600 = SYNCHRONIZATION MARK ERROR 1601 = DATA SYNC ERROR - DATA REWRITTEN 1602 = DATA SYNC ERROR - RECOMMEND REWRITE 1603 = DATA SYNC ERROR - DATA AUTO-REALLOCATED 1604 = DATA SYNC ERROR - RECOMMEND REASSIGNMENT 1700 = RECOVERED DATA WITH NO ERROR CORRECTION APPLIED 1701 = RECOVERED DATA WITH RETRIES 1702 = RECOVERED DATA WITH POSITIVE HEAD OFFSET 1703 = RECOVERED DATA WITH NEGATIVE HEAD OFFSET 1704 = RECOVERED DATA WITH RETRIES AND/OR CIRC APPLIED 1705 = RECOVERED DATA USING PREVIOUS SECTOR ID 1706 = RECOVERED DATA WITHOUT ECC - DATA AUTO-REALLOCATED 1707 = RECOVERED DATA WITHOUT ECC - RECOMMEND REASSIGNMENT 1708 = RECOVERED DATA WITHOUT ECC - RECOMMEND REWRITE 1709 = RECOVERED DATA WITHOUT ECC - DATA REWRITTEN 1800 = RECOVERED DATA WITH ERROR CORRECTION APPLIED 1801 = RECOVERED DATA WITH ERROR CORRECTION & RETRIES APPLIED 1802 = RECOVERED DATA - DATA AUTO-REALLOCATED 1803 = RECOVERED DATA WITH CIRC 1804 = RECOVERED DATA WITH LEC 1805 = RECOVERED DATA - RECOMMEND REASSIGNMENT 1806 = RECOVERED DATA - RECOMMEND REWRITE 1807 = RECOVERED DATA WITH ECC - DATA REWRITTEN 1808 = RECOVERED DATA WITH LINKING 1900 = DEFECT LIST ERROR 1901 = DEFECT LIST NOT AVAILABLE 1902 = DEFECT LIST ERROR IN PRIMARY LIST 1903 = DEFECT LIST ERROR IN GROWN LIST 1A00 = PARAMETER LIST LENGTH ERROR 1B00 = SYNCHRONOUS DATA TRANSFER ERROR 1C00 = DEFECT LIST NOT FOUND 1C01 = PRIMARY DEFECT LIST NOT FOUND 1C02 = GROWN DEFECT LIST NOT FOUND 1D00 = MISCOMPARE DURING VERIFY OPERATION 1E00 = RECOVERED ID WITH ECC 1F00 = RESERVED 2000 = INVALID COMMAND OPERATION CODE 2001 = ACCESS DENIED - INITIATOR PENDING-ENROLLED 2002 = ACCESS DENIED - NO ACCESS RIGHTS 2003 = ACCESS DENIED - INVALID MGMT ID KEY 2004 = ILLEGAL COMMAND WHILE IN WRITE CAPABLE STATE 2005 = Obsolete 2006 = ILLEGAL COMMAND WHILE IN EXPLICIT ADDRESS MODE 2007 = ILLEGAL COMMAND WHILE IN IMPLICIT ADDRESS MODE 2008 = ACCESS DENIED - ENROLLMENT CONFLICT 2009 = ACCESS DENIED - INVALID LU IDENTIFIER 200A = ACCESS DENIED - INVALID PROXY TOKEN 200B = ACCESS DENIED - ACL LUN CONFLICT 2100 = LOGICAL BLOCK ADDRESS OUT OF RANGE 2101 = INVALID ELEMENT ADDRESS 2102 = INVALID ADDRESS FOR WRITE 2200 = ILLEGAL FUNCTION (SHOULD USE 20 00, 24 00, OR 26 00) 2300 = RESERVED 2400 = INVALID FIELD IN CDB 2401 = CDB DECRYPTION ERROR 2402 = Obsolete 2403 = Obsolete 2404 = SECURITY AUDIT VALUE FROZEN 2405 = SECURITY WORKING KEY FROZEN 2406 = NONCE NOT UNIQUE 2407 = NONCE TIMESTAMP OUT OF RANGE 2500 = LOGICAL UNIT NOT SUPPORTED 2600 = INVALID FIELD IN PARAMETER LIST 2601 = PARAMETER NOT SUPPORTED 2602 = PARAMETER VALUE INVALID 2603 = THRESHOLD PARAMETERS NOT SUPPORTED 2604 = INVALID RELEASE OF PERSISTENT RESERVATION 2605 = DATA DECRYPTION ERROR 2606 = TOO MANY TARGET DESCRIPTORS 2607 = UNSUPPORTED TARGET DESCRIPTOR TYPE CODE 2608 = TOO MANY SEGMENT DESCRIPTORS 2609 = UNSUPPORTED SEGMENT DESCRIPTOR TYPE CODE 260A = UNEXPECTED INEXACT SEGMENT 260B = INLINE DATA LENGTH EXCEEDED 260C = INVALID OPERATION FOR COPY SOURCE OR DESTINATION 260D = COPY SEGMENT GRANULARITY VIOLATION 260E = INVALID PARAMETER WHILE PORT IS ENABLED 2700 = WRITE PROTECTED 2701 = HARDWARE WRITE PROTECTED 2702 = LOGICAL UNIT SOFTWARE WRITE PROTECTED 2703 = ASSOCIATED WRITE PROTECT 2704 = PERSISTENT WRITE PROTECT 2705 = PERMANENT WRITE PROTECT 2706 = CONDITIONAL WRITE PROTECT 2800 = NOT READY TO READY TRANSITION(MEDIUM MAY HAVE CHANGED) 2801 = IMPORT OR EXPORT ELEMENT ACCESSED 2900 = POWER ON, RESET, OR BUS DEVICE RESET OCCURRED 2901 = POWER ON OCCURRED 2902 = SCSI BUS RESET OCCURRED 2903 = BUS DEVICE RESET FUNCTION OCCURRED 2904 = DEVICE INTERNAL RESET 2905 = TRANSCEIVER MODE CHANGED TO SINGLE-ENDED 2906 = TRANSCEIVER MODE CHANGED TO LVD 2907 = NEXUS LOSS OCCURRED 2A00 = PARAMETERS CHANGED 2A01 = MODE PARAMETERS CHANGED 2A02 = LOG PARAMETERS CHANGED 2A03 = RESERVATIONS PREEMPTED 2A04 = RESERVATIONS RELEASED 2A05 = REGISTRATIONS PREEMPTED 2A06 = ASYMMETRIC ACCESS STATE CHANGED 2A07 = IMPLICIT ASYMMETRIC ACCESS STATE TRANSITION FAILED 2B00 = COPY CANNOT EXECUTE SINCE HOST CANNOT DISCONNECT 2C00 = COMMAND SEQUENCE ERROR 2C01 = TOO MANY WINDOWS SPECIFIED 2C02 = INVALID COMBINATION OF WINDOWS SPECIFIED 2C03 = CURRENT PROGRAM AREA IS NOT EMPTY 2C04 = CURRENT PROGRAM AREA IS EMPTY 2C05 = ILLEGAL POWER CONDITION REQUEST 2C06 = PERSISTENT PREVENT CONFLICT 2C07 = PREVIOUS BUSY STATUS 2C08 = PREVIOUS TASK SET FULL STATUS 2C09 = PREVIOUS RESERVATION CONFLICT STATUS 2C0A = PARTITION OR COLLECTION CONTAINS USER OBJECTS 2D00 = OVERWRITE ERROR ON UPDATE IN PLACE 2E00 = RESERVED 2F00 = COMMANDS CLEARED BY ANOTHER INITIATOR 3000 = INCOMPATIBLE MEDIUM INSTALLED 3001 = CANNOT READ MEDIUM - UNKNOWN FORMAT 3002 = CANNOT READ MEDIUM - INCOMPATIBLE FORMAT 3003 = CLEANING CARTRIDGE INSTALLED 3004 = CANNOT WRITE MEDIUM - UNKNOWN FORMAT 3005 = CANNOT WRITE MEDIUM - INCOMPATIBLE FORMAT 3006 = CANNOT FORMAT MEDIUM - INCOMPATIBLE MEDIUM 3007 = CLEANING FAILURE 3008 = CANNOT WRITE - APPLICATION CODE MISMATCH 3009 = CURRENT SESSION NOT FIXATED FOR APPEND 300A = CLEANING REQUEST REJECTED 3010 = MEDIUM NOT FORMATTED 3100 = MEDIUM FORMAT CORRUPTED 3101 = FORMAT COMMAND FAILED 3102 = ZONED FORMATTING FAILED DUE TO SPARE LINKING 3200 = NO DEFECT SPARE LOCATION AVAILABLE 3201 = DEFECT LIST UPDATE FAILURE 3300 = TAPE LENGTH ERROR 3400 = ENCLOSURE FAILURE 3500 = ENCLOSURE SERVICES FAILURE 3501 = UNSUPPORTED ENCLOSURE FUNCTION 3502 = ENCLOSURE SERVICES UNAVAILABLE 3503 = ENCLOSURE SERVICES TRANSFER FAILURE 3504 = ENCLOSURE SERVICES TRANSFER REFUSED 3600 = RIBBON, INK, OR TONER FAILURE 3700 = ROUNDED PARAMETER 3800 = EVENT STATUS NOTIFICATION 3802 = ESN - POWER MANAGEMENT CLASS EVENT 3804 = ESN - MEDIA CLASS EVENT 3806 = ESN - DEVICE BUSY CLASS EVENT 3900 = SAVING PARAMETERS NOT SUPPORTED 3A00 = MEDIUM NOT PRESENT 3A01 = MEDIUM NOT PRESENT - TRAY CLOSED 3A02 = MEDIUM NOT PRESENT - TRAY OPEN 3A03 = MEDIUM NOT PRESENT - LOADABLE 3A04 = MEDIUM NOT PRESENT - MEDIUM AUXILIARY MEMORY ACCESSIBLE 3B00 = SEQUENTIAL POSITIONING ERROR 3B01 = TAPE POSITION ERROR AT BEGINNING-OF-MEDIUM 3B02 = TAPE POSITION ERROR AT END-OF-MEDIUM 3B03 = TAPE OR ELECTRONIC VERTICAL FORMS UNIT NOT READY 3B04 = SLEW FAILURE 3B05 = PAPER JAM 3B06 = FAILED TO SENSE TOP-OF-FORM 3B07 = FAILED TO SENSE BOTTOM-OF-FORM 3B08 = REPOSITION ERROR 3B09 = READ PAST END OF MEDIUM 3B0A = READ PAST BEGINNING OF MEDIUM 3B0B = POSITION PAST END OF MEDIUM 3B0C = POSITION PAST BEGINNING OF MEDIUM 3B0D = MEDIUM DESTINATION ELEMENT FULL 3B0E = MEDIUM SOURCE ELEMENT EMPTY 3B0F = END OF MEDIUM REACHED 3B11 = MEDIUM MAGAZINE NOT ACCESSIBLE 3B12 = MEDIUM MAGAZINE REMOVED 3B13 = MEDIUM MAGAZINE INSERTED 3B14 = MEDIUM MAGAZINE LOCKED 3B15 = MEDIUM MAGAZINE UNLOCKED 3B16 = MECHANICAL POSITIONING OR CHANGER ERROR 3C00 = RESERVED 3D00 = INVALID BITS IN IDENTIFY MESSAGE 3E00 = LOGICAL UNIT HAS NOT SELF-CONFIGURED YET 3E01 = LOGICAL UNIT FAILURE 3E02 = TIMEOUT ON LOGICAL UNIT 3E03 = LOGICAL UNIT FAILED SELF-TEST 3E04 = LOGICAL UNIT UNABLE TO UPDATE SELF-TEST LOG 3F00 = TARGET OPERATING CONDITIONS HAVE CHANGED 3F01 = MICROCODE HAS BEEN CHANGED 3F02 = CHANGED OPERATING DEFINITION 3F03 = INQUIRY DATA HAS CHANGED 3F04 = COMPONENT DEVICE ATTACHED 3F05 = DEVICE IDENTIFIER CHANGED 3F06 = REDUNDANCY GROUP CREATED OR MODIFIED 3F07 = REDUNDANCY GROUP DELETED 3F08 = SPARE CREATED OR MODIFIED 3F09 = SPARE DELETED 3F0A = VOLUME SET CREATED OR MODIFIED 3F0B = VOLUME SET DELETED 3F0C = VOLUME SET DEASSIGNED 3F0D = VOLUME SET REASSIGNED 3F0E = REPORTED LUNS DATA HAS CHANGED 3F0F = ECHO BUFFER OVERWRITTEN 3F10 = MEDIUM LOADABLE 3F11 = MEDIUM AUXILIARY MEMORY ACCESSIBLE 4000 = RAM FAILURE (SHOULD USE 40 NN) 40NN = DIAGNOSTIC FAILURE ON COMPONENT NN (80H-FFH) 4100 = DATA PATH FAILURE (SHOULD USE 40 NN) 4200 = POWER-ON OR SELF-TEST FAILURE (SHOULD USE 40 NN) 4300 = MESSAGE ERROR 4400 = INTERNAL TARGET FAILURE 4500 = SELECT OR RESELECT FAILURE 4600 = UNSUCCESSFUL SOFT RESET 4700 = SCSI PARITY ERROR 4701 = DATA PHASE CRC ERROR DETECTED 4702 = SCSI PARITY ERROR DETECTED DURING ST DATA PHASE 4703 = INFORMATION UNIT iuCRC ERROR DETECTED 4704 = ASYNCHRONOUS INFORMATION PROTECTION ERROR DETECTED 4705 = PROTOCOL SERVICE CRC ERROR 477F = SOME COMMANDS CLEARED BY ISCSI PROTOCOL EVENT 4800 = INITIATOR DETECTED ERROR MESSAGE RECEIVED 4900 = INVALID MESSAGE ERROR 4A00 = COMMAND PHASE ERROR 4B00 = DATA PHASE ERROR 4B01 = INVALID TARGET PORT TRANSFER TAG RECEIVED 4B02 = TOO MUCH WRITE DATA 4B03 = ACK/NAK TIMEOUT 4B04 = NAK RECEIVED 4B05 = DATA OFFSET ERROR 4B06 = INITIATOR RESPONSE TIMEOUT 4C00 = LOGICAL UNIT FAILED SELF-CONFIGURATION 4D00 = TAGGED OVERLAPPED COMMANDS (NN = QUEUE TAG) 4E00 = OVERLAPPED COMMANDS ATTEMPTED 4F00 = RESERVED 5000 = WRITE APPEND ERROR 5001 = WRITE APPEND POSITION ERROR 5002 = POSITION ERROR RELATED TO TIMING 5100 = ERASE FAILURE 5101 = ERASE FAILURE - INCOMPLETE ERASE OPERATION DETECTED 5200 = CARTRIDGE FAULT 5300 = MEDIA LOAD OR EJECT FAILED 5301 = UNLOAD TAPE FAILURE 5302 = MEDIUM REMOVAL PREVENTED 5400 = SCSI TO HOST SYSTEM INTERFACE FAILURE 5500 = SYSTEM RESOURCE FAILURE 5501 = SYSTEM BUFFER FULL 5502 = INSUFFICIENT RESERVATION RESOURCES 5503 = INSUFFICIENT RESOURCES 5504 = INSUFFICIENT REGISTRATION RESOURCES 5505 = INSUFFICIENT ACCESS CONTROL RESOURCES 5506 = AUXILIARY MEMORY OUT OF SPACE 5600 = RESERVED 5700 = UNABLE TO RECOVER TABLE-OF-CONTENTS 5800 = GENERATION DOES NOT EXIST 5900 = UPDATED BLOCK READ 5A00 = OPERATOR REQUEST OR STATE CHANGE INPUT (UNSPECIFIED) 5A01 = OPERATOR MEDIUM REMOVAL REQUEST 5A02 = OPERATOR SELECTED WRITE PROTECT 5A03 = OPERATOR SELECTED WRITE PERMIT 5B00 = LOG EXCEPTION 5B01 = THRESHOLD CONDITION MET 5B02 = LOG COUNTER AT MAXIMUM 5B03 = LOG LIST CODES EXHAUSTED 5C00 = STATUS CHANGE 5C01 = SPINDLES SYNCHRONIZED 5C02 = SPINDLES NOT SYNCHRONIZED 5D00 = FAILURE PREDICTION THRESHOLD EXCEEDED 5D01 = MEDIA FAILURE PREDICTION THRESHOLD EXCEEDED 5D02 = LOGICAL UNIT FAILURE PREDICTION THRESHOLD EXCEEDED 5D03 = SPARE AREA EXHAUSTION PREDICTION THRESHOLD EXCEEDED 5D10 = HARDWARE IMPENDING FAILURE GENERAL HARD DRIVE FAILURE 5D11 = HARDWARE IMPENDING FAILURE DRIVE ERROR RATE TOO HIGH 5D12 = HARDWARE IMPENDING FAILURE DATA ERROR RATE TOO HIGH 5D13 = HARDWARE IMPENDING FAILURE SEEK ERROR RATE TOO HIGH 5D14 = HARDWARE IMPENDING FAILURE TOO MANY BLOCK REASSIGNS 5D15 = HARDWARE IMPENDING FAILURE ACCESS TIMES TOO HIGH 5D16 = HARDWARE IMPENDING FAILURE START UNIT TIMES TOO HIGH 5D17 = HARDWARE IMPENDING FAILURE CHANNEL PARAMETRICS 5D18 = HARDWARE IMPENDING FAILURE CONTROLLER DETECTED 5D19 = HARDWARE IMPENDING FAILURE THROUGHPUT PERFORMANCE 5D1A = HARDWARE IMPENDING FAILURE SEEK TIME PERFORMANCE 5D1B = HARDWARE IMPENDING FAILURE SPIN-UP RETRY COUNT 5D1C = HARDWARE IMPENDING FAILURE DRIVE CALIBRATION RETRY COUNT 5D20 = CONTROLLER IMPENDING FAILURE GENERAL HARD DRIVE FAILURE 5D21 = CONTROLLER IMPENDING FAILURE DRIVE ERROR RATE TOO HIGH 5D22 = CONTROLLER IMPENDING FAILURE DATA ERROR RATE TOO HIGH 5D23 = CONTROLLER IMPENDING FAILURE SEEK ERROR RATE TOO HIGH 5D24 = CONTROLLER IMPENDING FAILURE TOO MANY BLOCK REASSIGNS 5D25 = CONTROLLER IMPENDING FAILURE ACCESS TIMES TOO HIGH 5D26 = CONTROLLER IMPENDING FAILURE START UNIT TIMES TOO HIGH 5D27 = CONTROLLER IMPENDING FAILURE CHANNEL PARAMETRICS 5D28 = CONTROLLER IMPENDING FAILURE CONTROLLER DETECTED 5D29 = CONTROLLER IMPENDING FAILURE THROUGHPUT PERFORMANCE 5D2A = CONTROLLER IMPENDING FAILURE SEEK TIME PERFORMANCE 5D2B = CONTROLLER IMPENDING FAILURE SPIN-UP RETRY COUNT 5D2C = CONTROLLER IMPENDING FAILURE DRIVE CALIBRATION RETRY COUNT 5D30 = DATA CHANNEL IMPENDING FAILURE GENERAL HARD DRIVE FAILURE 5D31 = DATA CHANNEL IMPENDING FAILURE DRIVE ERROR RATE TOO HIGH 5D32 = DATA CHANNEL IMPENDING FAILURE DATA ERROR RATE TOO HIGH 5D33 = DATA CHANNEL IMPENDING FAILURE SEEK ERROR RATE TOO HIGH 5D34 = DATA CHANNEL IMPENDING FAILURE TOO MANY BLOCK REASSIGNS 5D35 = DATA CHANNEL IMPENDING FAILURE ACCESS TIMES TOO HIGH 5D36 = DATA CHANNEL IMPENDING FAILURE START UNIT TIMES TOO HIGH 5D37 = DATA CHANNEL IMPENDING FAILURE CHANNEL PARAMETRICS 5D38 = DATA CHANNEL IMPENDING FAILURE CONTROLLER DETECTED 5D39 = DATA CHANNEL IMPENDING FAILURE THROUGHPUT PERFORMANCE 5D3A = DATA CHANNEL IMPENDING FAILURE SEEK TIME PERFORMANCE 5D3B = DATA CHANNEL IMPENDING FAILURE SPIN-UP RETRY COUNT 5D3C = DATA CHANNEL IMPENDING FAILURE DRIVE CALIBRATION RETRY COUNT 5D40 = SERVO IMPENDING FAILURE GENERAL HARD DRIVE FAILURE 5D41 = SERVO IMPENDING FAILURE DRIVE ERROR RATE TOO HIGH 5D42 = SERVO IMPENDING FAILURE DATA ERROR RATE TOO HIGH 5D43 = SERVO IMPENDING FAILURE SEEK ERROR RATE TOO HIGH 5D44 = SERVO IMPENDING FAILURE TOO MANY BLOCK REASSIGNS 5D45 = SERVO IMPENDING FAILURE ACCESS TIMES TOO HIGH 5D46 = SERVO IMPENDING FAILURE START UNIT TIMES TOO HIGH 5D47 = SERVO IMPENDING FAILURE CHANNEL PARAMETRICS 5D48 = SERVO IMPENDING FAILURE CONTROLLER DETECTED 5D49 = SERVO IMPENDING FAILURE THROUGHPUT PERFORMANCE 5D4A = SERVO IMPENDING FAILURE SEEK TIME PERFORMANCE 5D4B = SERVO IMPENDING FAILURE SPIN-UP RETRY COUNT 5D4C = SERVO IMPENDING FAILURE DRIVE CALIBRATION RETRY COUNT 5D50 = SPINDLE IMPENDING FAILURE GENERAL HARD DRIVE FAILURE 5D51 = SPINDLE IMPENDING FAILURE DRIVE ERROR RATE TOO HIGH 5D52 = SPINDLE IMPENDING FAILURE DATA ERROR RATE TOO HIGH 5D53 = SPINDLE IMPENDING FAILURE SEEK ERROR RATE TOO HIGH 5D54 = SPINDLE IMPENDING FAILURE TOO MANY BLOCK REASSIGNS 5D55 = SPINDLE IMPENDING FAILURE ACCESS TIMES TOO HIGH 5D56 = SPINDLE IMPENDING FAILURE START UNIT TIMES TOO HIGH 5D57 = SPINDLE IMPENDING FAILURE CHANNEL PARAMETRICS 5D58 = SPINDLE IMPENDING FAILURE CONTROLLER DETECTED 5D59 = SPINDLE IMPENDING FAILURE THROUGHPUT PERFORMANCE 5D5A = SPINDLE IMPENDING FAILURE SEEK TIME PERFORMANCE 5D5B = SPINDLE IMPENDING FAILURE SPIN-UP RETRY COUNT 5D5C = SPINDLE IMPENDING FAILURE DRIVE CALIBRATION RETRY COUNT 5D60 = FIRMWARE IMPENDING FAILURE GENERAL HARD DRIVE FAILURE 5D61 = FIRMWARE IMPENDING FAILURE DRIVE ERROR RATE TOO HIGH 5D62 = FIRMWARE IMPENDING FAILURE DATA ERROR RATE TOO HIGH 5D63 = FIRMWARE IMPENDING FAILURE SEEK ERROR RATE TOO HIGH 5D64 = FIRMWARE IMPENDING FAILURE TOO MANY BLOCK REASSIGNS 5D65 = FIRMWARE IMPENDING FAILURE ACCESS TIMES TOO HIGH 5D66 = FIRMWARE IMPENDING FAILURE START UNIT TIMES TOO HIGH 5D67 = FIRMWARE IMPENDING FAILURE CHANNEL PARAMETRICS 5D68 = FIRMWARE IMPENDING FAILURE CONTROLLER DETECTED 5D69 = FIRMWARE IMPENDING FAILURE THROUGHPUT PERFORMANCE 5D6A = FIRMWARE IMPENDING FAILURE SEEK TIME PERFORMANCE 5D6B = FIRMWARE IMPENDING FAILURE SPIN-UP RETRY COUNT 5D6C = FIRMWARE IMPENDING FAILURE DRIVE CALIBRATION RETRY COUNT 5DFF = FAILURE PREDICTION THRESHOLD EXCEEDED (FALSE) 5E00 = LOW POWER CONDITION ON 5E01 = IDLE CONDITION ACTIVATED BY TIMER 5E02 = STANDBY CONDITION ACTIVATED BY TIMER 5E03 = IDLE CONDITION ACTIVATED BY COMMAND 5E04 = STANDBY CONDITION ACTIVATED BY COMMAND 5E41 = POWER STATE CHANGE TO ACTIVE 5E42 = POWER STATE CHANGE TO IDLE 5E43 = POWER STATE CHANGE TO STANDBY 5E45 = POWER STATE CHANGE TO SLEEP 5E47 = POWER STATE CHANGE TO DEVICE CONTROL 5F00 = RESERVED 6000 = LAMP FAILURE 6100 = VIDEO ACQUISITION ERROR 6101 = UNABLE TO ACQUIRE VIDEO 6102 = OUT OF FOCUS 6200 = SCAN HEAD POSITIONING ERROR 6300 = END OF USER AREA ENCOUNTERED ON THIS TRACK 6301 = PACKET DOES NOT FIT IN AVAILABLE SPACE 6400 = ILLEGAL MODE FOR THIS TRACK 6401 = INVALID PACKET SIZE 6500 = VOLTAGE FAULT 6600 = AUTOMATIC DOCUMENT FEEDER COVER UP 6601 = AUTOMATIC DOCUMENT FEEDER LIFT UP 6602 = DOCUMENT JAM IN AUTOMATIC DOCUMENT FEEDER 6603 = DOCUMENT MISS FEED AUTOMATIC IN DOCUMENT FEEDER 6700 = CONFIGURATION FAILURE 6701 = CONFIGURATION OF INCAPABLE LOGICAL UNITS FAILED 6702 = ADD LOGICAL UNIT FAILED 6703 = MODIFICATION OF LOGICAL UNIT FAILED 6704 = EXCHANGE OF LOGICAL UNIT FAILED 6705 = REMOVE OF LOGICAL UNIT FAILED 6706 = ATTACHMENT OF LOGICAL UNIT FAILED 6707 = CREATION OF LOGICAL UNIT FAILED 6708 = ASSIGN FAILURE OCCURRED 6709 = MULTIPLY ASSIGNED LOGICAL UNIT 670A = SET TARGET PORT GROUPS COMMAND FAILED 6800 = LOGICAL UNIT NOT CONFIGURED 6900 = DATA LOSS ON LOGICAL UNIT 6901 = MULTIPLE LOGICAL UNIT FAILURES 6902 = PARITY/DATA MISMATCH 6A00 = INFORMATIONAL, REFER TO LOG 6B00 = STATE CHANGE HAS OCCURRED 6B01 = REDUNDANCY LEVEL GOT BETTER 6B02 = REDUNDANCY LEVEL GOT WORSE 6C00 = REBUILD FAILURE OCCURRED 6D00 = RECALCULATE FAILURE OCCURRED 6E00 = COMMAND TO LOGICAL UNIT FAILED 6F00 = COPY PROTECTION KEY EXCHANGE FAILURE - AUTHENTICATION FAILURE 6F01 = COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT PRESENT 6F02 = COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED 6F03 = READ OF SCRAMBLED SECTOR WITHOUT AUTHENTICATION 6F04 = MEDIA REGION CODE IS MISMATCHED TO LOGICAL UNIT REGION 6F05 = DRIVE REGION MUST BE PERMANENT/REGION RESET COUNT ERROR 7000 = DECOMPRESSION EXCEPTION SHORT ALGORITHM ID OF 0 7100 = DECOMPRESSION EXCEPTION LONG ALGORITHM ID 7200 = SESSION FIXATION ERROR 7201 = SESSION FIXATION ERROR WRITING LEAD-IN 7202 = SESSION FIXATION ERROR WRITING LEAD-OUT 7203 = SESSION FIXATION ERROR - INCOMPLETE TRACK IN SESSION 7204 = EMPTY OR PARTIALLY WRITTEN RESERVED TRACK 7205 = NO MORE TRACK RESERVATIONS ALLOWED 7300 = CD CONTROL ERROR 7301 = POWER CALIBRATION AREA ALMOST FULL 7302 = POWER CALIBRATION AREA IS FULL 7303 = POWER CALIBRATION AREA ERROR 7304 = PROGRAM MEMORY AREA UPDATE FAILURE 7305 = PROGRAM MEMORY AREA IS FULL 7306 = RMA/PMA IS ALMOST FULL 7400 = RESERVED 7500 = RESERVED 7600 = RESERVED 7700 = RESERVED 7800 = RESERVED 7900 = RESERVED 7A00 = RESERVED 7B00 = RESERVED 7C00 = RESERVED 7D00 = RESERVED 7E00 = RESERVED 7F00 = RESERVEDDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.