Release Notes ============= Broadcom NetXtreme Gigabit Ethernet Driver For Netware 4.x, 5.x, 6.x Copyright (c) 2000-2003 Broadcom Corporation All rights reserved. Version 6.04 May 12, 2003 ------------------------- Fixes: ======== 1. Problem: (CQ #4441) Cause: Only seen on NetWare 4.2 server & only seen on specific machines when sharing IRQs w\multiple Broadcom Adapters: OS occasionally loops on the wrong adapter driver entry point. The System appears non functional. Change: Code was added to detect this condition and allow the OS to call a different driver entry point. Impact: All adapters. There should be no noticable difference if earlier driver versions function properly. 2. Problem: (CQ #7729) Cause: Driver displayed 570x when 5901 was loaded. Change: The driver displays a non adapter specific string. Impact: Same string is displayed for all adapters. Version 6.03 April 29, 2003 ------------------------- Fixes: ======== 1. Problem: (CQ #7280) Cause: Phy Locks up when continual resets to phy occur. Note: This a very rare condition and may not be reproducible. Change: Check the phy after each phy reset to determine if lockup occurs. Additional phy reset clears lockup. Impact: The fix to this problem should not be noticeable. Fix is activated in 5703, 5704, 5705 adapters. 03/20/03 v6.02 Added support for 5788. Removed WireSpeed keyword. 02/14/03 v6.01 Changed jumbo support from 9100 max to 9000 max. Link message is changed. Fixed CarrierSense Counter. Added new Device IDs. 01/13/03 v5.09 Fixed cable disconnect delay for server. 01/02/03 v5.06 Fixed cable disconnect delay for Client32. 12/20/02 v5.05 Enhanced client32 support. 12/09/02 v5.04 Added PCIX mode status in custom stats. Fixed Link mode. 11/22/02 v5.03 Fixed client32 slow connection problem. Checksum offload is default off. 11/08/02 v5.02 Fixed checksum problem found in NW6 support pack 2. 10/29/02 v5.01 Fixed rare eeprom read bug. 09/26/02 v5.00 This version has 5705 support. 09/26/02 v4.00 Fixed client32 cable disconnect bug. Took out 5705 support. 08/21/02 v3.03 Added support for 5705. 05/13/02 v3.02 Changed water marks for performance tuning. 05/13/02 v3.01 Fixed bug in tx checksum that prevented snmp events. Fixed bug preventing completion of 72 hour stress test. 05/03/02 v3.00 Added support for 5704 controller. 05/07/02 v2.32 Fixed bug in tx checksum that prevented snmp events. 04/19/02 v2.31 Added delays in driver for initialization. 03/22/02 v2.29 Fix of Jumbo size reported to Netware certification. 03/20/02 v2.28 Added changes to control LEDs. 03/19/02 v2.27 Added two command line keywords: fiber=auto/force & MagicP=0/1. 03/14/02 v2.26 Changed driver to work in DOS CLIENT32. VLAN support broken on older versions of BASP use only on BASP 2.09 or later. 02/25/02 v2.25 Fixed some keywords that were not being reset properly. Added WireSpeed feature. 02/07/02 v2.24 Added Jumbo frame dynamic size. Poll mode display. 01/22/02 v2.23 Fixed dropped client problem. 01/22/02 v2.22 Further enhancement of the spurious int fix. 01/19/02 v2.21 Spurious int fix is now default on. 12/19/01 v2.20 Added code to better handle spurious interrupts on some machines. 12/06/01 v2.19 Fixed ipx vlan problem. 11/28/01 v2.18 Fixed 100 hr stress problem. 11/16/01 v2.17 Fixed multicast address size, performance improvement. 11/07/01 v2.16 Fixed backward compatibility probs. 10/30/01 v2.15 Jumbo certified. 09/18/01 v2.14 Fixed cable fault problem. 09/12/01 v2.12 Fixed FrameAlignment & ChecksumError counters. 08/24/01 v2.10 Fixed a PCIX problem. 08/17/01 v2.09 Fixed a jumbo mode problem. 08/03/01 v2.08 Fixed Perform3 problem. 07/20/01 v2.07 Improved fiber support. 07/06/01 v2.06 802.3 bug fix. 07/02/01 v2.05 Fix for fiber link. Fix for shutdown. 06/14/01 v2.02 Fixed fiber support/performance improvements. 06/04/01 v2.01 Rebuild for new release. 05/04/01 v1.27 Added registration for advanced server program. 04/24/01 v1.25 supports 5701 04/12/01 v1.23 Reset bug fix. 03/27/01 v1.22 Jumbo frame support added. 02/26/01 v1.20 Checksum is default off. 02/15/01 v1.18 Fix for vlan bug in ipx, and min packet size with vlan. 02/08/01 v1.16 Fixed bug for 4.x primary install. 02/05/01 v1.15 Fixed new persistent driver bug, multicast bug, and basp support bug. 01/30/01 v1.12 Fix for vlans. 01/29/01 v1.10 Added changes in PCI-X support. 01/26/01 v1.09 Fixed NESL bug. 01/19/01 v1.08 Fixed persistent driver mode bug. 01/05/01 v1.07 Added persistent driver mode. 12/29/00 v1.06 Added better checksum support. 12/21/00 v1.05 Added more user info. 12/15/00 v1.04 Fixed spurious interrupt reports. 12/11/00 v1.03 Made changes for better performance. 12/08/00 v1.02 Added better ipx w/802.3 support. 12/01/00 v1.01 Added console status messages for link up/down. 11/27/00 v1.00 1st release. 11/22/00 v0.26 Real update of lower module. 11/22/00 v0.25 Updated lower module for led change. 11/22/00 v0.24 Added support for 32 minimum receive buffers. 11/18/00 v0.23 Updated lower module for better flow control. Passes Novell certification. 11/17/00 -v0.22 Upgraded the checksum off load support & receive code. 11/08/00 -v0.21 Updated lower module. 11/06/00 -v0.20 Fixed link problem and unwanted messages. 11/03/00 -v0.19 Added support for new firmware. 11/01/00 -v0.18 Fixed vlan bug for large packets. Changed promiscuous mode support. 10/30/00 -v0.17 Added vlan support for BASP. 10/28/00 -v0.16 Added code to guard against ECB starvation. Enhanced code for speed parameter. 10/23/00 -v0.15 Added a custom NESL event for changing the MAC address to work with BASP. 10/20/00 -v0.14 Made adjustments for certification test. 10/16/00 -v0.13 New release. 10/13/00 -v0.12 Fortified reset code and isr. 10/6/00 - v0.11 Added support for sharing ints between multiple B57s. Added support for "auto" within the speed keyword. Displays line speed more consistently. 9/22/00 - v0.10 Changed allocated resources amount. Fixed bug in user defined parameters. 9/20/00 - v0.09 Change in reset and interrupt code (checks if initialized). 9/14/00 - v0.08a Changed interrupt enable/disable. 9/13/00 - v0.08- First Engineering Release.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.